SVEN SRP-100 Portable Radio User Manual

SVEN SRP-100 Portable Radio

SPECIAL FEATURES

•  8 inch LED display withwith four brightness levels
•  Built-in clock and alarm
• Built-in FM radio 87.5~108khz
•  Sleep function
• Wake up mode of buzzer or radio

Description

• ALM1/VOL -: volume decrease; Alarm settings
• ALM2/VOL+: volume increase; Alarm settings
• SNOOZE/DIMMER brightness control button; Disabling the alarm
• TUN-/MEM- : station switching – (short pressing); Setting hours and minutes. Station search, frequency – (long pressing)
• TUN+/MEM +: station switching + (short pressing); Setting hours and minutes. Station search, frequency + (long pressing)
• Battery charge indicator. (Constantly lit in charge mode. Blinking-low battery) g FM mode indicator (Radio)
• Indicator PM (afternoon)
• LED display
• Indicator SLEEP («sleep» function)
• Indicator ALM1 (alarm clock 1 is on)
• Indicator ALM2 (alarm clock 2 is on) m Telescopic swivel antenna
• Battery cover
• 12H/24H/TIME SET/DELETE: clock setting button
• SLEEP/SAVE: sleep mode setting button/memorizing radio station
• ON/OFF/SCAN : On/off button; Scan FM band
• DC IN: Type-C jack for connecting radio to the charger, the USB port of laptop/PC (battery charging)

CONNECTION AND OPERATION

Attention! The built-in battery must be charged completely prior to the application.
Battery charging

Connect radio to a USB port of PC or USB charger using Type-C to USB cable (included). When charging, the indicator f lights up. Indicator f goes out if thebattery is charged. When the battery is low, the indicator light starts blinking.

OPERATION MODES

Clock function
The product has two basic operating modes:

1.  Radio mode. Radio listening mode.
2. Standby mode. Mode when the radio is off.

Time setting

• In standby mode, press and hold button o for 3 seconds, the hour value will start blinking, use buttons d and e to set the desired value. Then press button o the minute value will start blinking, use buttons d and e to set the desired value.
• To complete the time setting, press button o again. If no operation is performed for 5 seconds during this operation, the unit will return to standby mode.In standby mode, press button o to switch 12/24H mode.
• Default time display mode is 12H. (in the afternoon the PM indicator is on).

Alarm function

• In standby mode, press and hold button a for 3 seconds, the hour value will start blinking, use buttons d and e to set the desired value. Then press button a the minute value will start blinking, use buttons d and e to set the desired value.
•  Press button a again, then use buttons d and e to choose Buzzer or FM alarm mode.
•  Press button a, use buttons d and e to set the maximum volume for the alarm.
•  Finally, press button a, again to complete the setting of the Alarm and the ALM1 indicator k will light up.
• If no operation is performed for more than 5 seconds during setup, the unit will return to Watch mode.
• The second alarm is set similarly to button b.
• LED activity indicator alarm k/l respectively.
• Pause the alarm signal with button c, while the LED indicator of the corresponding alarm clock lights up intermittently. The repeated signal will turn on in 10 minutes.
• The signal is turned off by pressing button a/b in accordance with the alarm number.

Radio mode

•  In standby mode, press button q to switch to FM mode, the station frequency will appear on the display and the FM indicator g will light up.
• In FM mode, press and hold button q for 3 seconds – the auto search mode is activated (stations in the range from 87.5 MHz to 108 MHz), all stations found will be automatically saved.
• After completing the tuning, you can select the desired station using buttons d and e.
• If no operation is performed for more than 5 seconds during setup, the unit will switch to the current time display mode.

Searching for stations manually

• Press and hold for 3 seconds button d turns on station search down the range, press and hold for 3 seconds button e, turn on station search up the range.
• To store the station, press and hold the button SLEEP p for 3 seconds, the display i will show «P##», press the button d or e to select the station number you want to store. Press the SLEEP p button to end the manual storage of stations.

Volume control

•  Adjust the volume using buttons a and b.

Adjusting the brightness of the LED display

•  Press button c to select the desired brightness of the LED display, 4 levels: bright – medium – dark – off. By default, the brightness level is medium.

TECHNICAL SPECIFICATIONS

3.7В/1200 mAh USB/            5V

Rated current, A| 0.074
Colour| black
Dimensions, mm| 157 × 44 × 88
Weight, kg| 0.22

NOTES

• Technical specifications given in this table are supplemental information and cannot giveoccasion to claims.
• Technical specifications and package contents are subject to change without notice due to the improvement of SVEN production.

Portable Radio

Model: SRP-100
Importer: Tiralana OY, Office 102, Kotolahdentie 15, 48310 Kotka, Finland.

Manufacturer: SVEN PTE. LTD, 176 Joo Chiat Road, № 02-02, Singapore, 427447. Produced under the control of Oy Sven Scandinavia Ltd. 15, Kotolahdentie, Kotka, Finland, 48310. Made in China.

Registered Trademark of Oy SVEN
Scandinavia Ltd. Finland.

Documents / Resources

| SVEN SRP-100 Portable Radio [pdf] User Manual
SRP-100, Portable Radio
---|---
| SVEN SRP-100 Portable Radio [pdf] User Manual
SRP-100, Portable Radio

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>