NITECORE BR25 High Performance Ultra Compact Bike Light Instruction Manual
- June 6, 2024
- Nitecore
Table of Contents
BR25
High-Performance Ultra
Compact Bike Light
Instruction Manual
- Innovative Diffuse Reflection Design
- Bike Mount with Quick Dismounting
- Patented ATR Technology
Features
- Utilizes a Luminus SST-40-W LED with a max output of 1,400 lumens
- Utilizes an OP reflector for a wide range of soft beam
- Max peak beam intensity of 6,700cd and max throw of 163 meters
- Utilizes a diffuse reflection board to illuminate the blind spot underfoot with a close-range beam
- Powered by a 21700 high capacity Li-ion battery while compatible with 18650 and CR123 batteries, to provides a runtime of up to 60 hours
- A highly efficient constant current circuit provides a stable output
- One side switch controls 4 brightness levels and Warning Flashing
- The power indicator beneath the switch indicates the remaining battery power
- The power indicator can also display the battery voltage (±0.1V)
- NITECORE 21700 Li-ion battery included (NL2150R 5,000mAh)
- Incorporated Advanced Temperature Regulation (ATR) module (Patent No. ZL201510534543.6)
- Tube constructed from aero grade aluminum alloy with HA III military grade hard-anodized finish
- Bike mount included for quick dismounting
- Waterproof and dustproof rating in accordance with IP68 (2 meters submersible)
- Impact-resistant to 1 meter
Battery Options
| Type| Nominal Voltage| Compatibility
---|---|---|---
21700 Rechargeable Li-ion Battery
(Discharge Current Over 8A)| 21700| 3.6V/3.7V| Y (Recommended)
18650 Rechargeable Li-ion Battery
(Discharge Current Over 8A)| 18650| 3.6V/3.7V| Y (Compatible)
Primary Lithium Battery| CR123| 3V| Y (Compatible)
Rechargeable Li-ion Battery| RCR123| 3.6V/3.7V| Y (Compatible)
21700 Rechargeable Li-ion Battery
(Discharge Current Below 8A)| 21700| 3.6V/3.7V| N (Incompatible)
18650 Rechargeable Li-ion Battery
(Discharge Current Below 8A)| 18650| 3.6V/3.N| N (Incompatible)
Technical Data
Using a 5,000mAh 21700 Li-ion Battery:
FLI STANDARD| TURBO| HIGH| MID| LOW| WARNING
FLASHING
---|---|---|---|---|---
| 1,400 Lumens| 430 Lumens| 170 Lumens| 28 Lumens| 1,400 Lumens
| 2h 30min| 3h 15min| 12h| 60h| —
| 163m| 91m| 50m| 20m| —
| 6,700cd| 2,060cd| 630cd| 108cd| —
| lm (Impact Resistance)
| IP68, 2m (Waterproof and Submersible)
Note: The stated data is measured in accordance with the international
flashlight testing standards ANSI/PLATO FL 1-2019, using 1 x 21700 Li-ion
battery (5,000mAh) under laboratory conditions. The data may vary in real-
world use due to different battery usage or environmental conditions.
Using 2 x CR123 Batteries:
FL1 STANDARD| TURBO| HIGH| MID| LOW| WARNING
FLASHING
---|---|---|---|---|---
| 820
Lumens| 430
Lumens| 170
Lumens| 28 Lumens| 820
Lumens
| 1h 15min| 2h| 5h 15min| 26h| —
| 119m| 91m| 50m| 20m| —
| 3,540cd| 2,060cd| 630cd| 108cd| —
| lm ( impact Resistance)
| IP68, 2m (Waterproof and Submersible)
Note: The stated data is measured in accordance with the international flashlight testing standard ANSI/PLATO FL 1-2019, using 2 x CR123 lithium batteries (1,700mAh) under laboratory conditions. The data may vary in real- world use due to different battery usage or environmental conditions.
Specifications
Length: Head
Width: Tube
Diameter: Tail
Diameter:
Weight: 148.6mm (5.85″) 30mm (1.18″) 25.4mm (1″) 27.2mm (1.07″) 76g (2.68oz)
(Bike Mount Not Included) 144.5g (5.1oz) (Bike Mount Included)
Accessories
NITECORE 21700 Rechargeable Li-ion Battery (NL2150R 5,000mAh), USB-C Charging Cable, Bike Mount for BR25 (with 2 x Thin Mount Pads), 2 x Thick Mount Pads, 18650/CR123 Battery Magazine, Spare O-ring, Lanyard
Battery Installation
Mounting
Operating Instructions
Battery Installation
Insert the battery(s) as illustrated and screw to tighten the tail cap. Note:
After battery insertion, the power indicator beneath the switch will flash to
indicate the battery voltage. Please refer to the “Power Indication” section
of this manual for more details. Warnings:
- Ensure the battery(s) is/are inserted with the positive end towards the head. The product will not work if the battery(s) is/are incorrectly inserted.
- Please use the battery magazine when using 1 x 18650 / 2 x CR123 batteries to avoid battery rattling and to ensure stable contact.
- CAUTION! Possible dangerous radiation! Don’t look into the light! May be dangerous for your eyes.
- When the power level is low, please stop using the product and replace or recharge the battery to prevent damage to the battery.
- When the product is kept in a backpack or left unused for a prolonged time, please remove all batteries to prevent accidental activation or battery leakage.
Mounting
- Loosen the screw of the handlebar mount and adjust the handlebar mount before clamping the mount to the handlebar by securely tightening the set screw.
- Slide the bike light into the bike mount as illustrated until it clicks into position.
Note:
- Please use proper mount pads provided according to the diameters of the handlebar. (34-38mm bar requires no pads; 29-35mm bar requires 2 thin pads: 25-29mm bar requires 1 thin pad and 1 thick pad; 20-25mm bar requires 2 thick pads)
- Please adjust the beam angle of the bike light accordingly before clamping the mount to the handlebar to avoid affecting the oncoming vehicles.
Quick Release of the Bike Light
Press and hold down the pedal on the back of the bike mount and pull out the
light towards the opposite direction when mounting the light.
On / Off
On: When the light is off, long-press the Power Button to turn it on. Off:
When the light is on, long-press the Power Button to turn it off.
Brightness Levels
When the light is on, short press the Power Button to cycle through the
following brightness levels: LOW MID HIGH TURBO. (The BR25 has mode
memory. When reactivated, it will automatically access the previous memorized
brightness level.)
Direct Access to TURBO
When the light is on (TURBO and Warning Flashing excluded), double press the
Power Button to directly access TURBO. Short press the Power Button again to
return to the previous brightness level, or it will automatically return to
the previous brightness level if there is no operation in 30 seconds.
Warning Flashing
When the light is on, triple press the Power Button to access Warning
Flashing. Short press the Power Button again to return to the previous
brightness level, or long-press the Power Button to turn off the light.
Power Indication
- When the battery is inserted, the power indicator will flash to show the battery voltage (±0.1V). For example, when the battery voltage is at 4.2V, the power indicator will flash 4 times followed by a 1.5-second pause and 2 more flashes. Different voltages represent the corresponding remaining battery power levels:
1×18650/ 21700 battery
2×CR123 batteries
Note: when using two CR123/RCR123 in series, the indicator will show the
average voltage between the two batteries.
When the Power Button is pressed when the light is off, the power the
indicator will flash to indicate the remaining power of the battery:
- Flashing three times indicates that the power is above 50%.
- Flashing twice indicates that the power is below 50%.
- Flashing once indicates that the power is below 10%.
- When the light is on and the power level is close to 50%, the power indicator will flash slowly to inform the user. When the light is on and the power is close to depleted, the power indicator will flash quickly and continuously to inform the user. The batteries should be replaced when the output appears to be dim or the bike light becomes unresponsive due to low power.
ATR (Advanced Temperature Regulation)
The integrated ATR technology regulates the output of the BR25 according to
the working condition and ambient environment to maintain optimal performance.
Maintenance
Every 6 months, threads should be wiped with a clean cloth followed by a thin
coating of silicone-based lubricant.
Warranty Service
All NITECORE® products are warranted for quality. Any DOA / defective product
can be exchanged for a replacement through a local distributor/dealer within
15 days of purchase. After that, all defective/malfunctioning NITECORE®
products can be repaired free of charge within 60 months from the date of
purchase. Beyond 60 months, a limited warranty applies, covering the cost of
labor and maintenance, but not the cost of accessories or replacement parts.
The warranty will be nullified if 1. the product(s) is/are broken down,
reconstructed, and/or modified by unauthorized parties; 2. the product(s)
is/are damaged due to improper use; (e.g. reversed polarity installation) 3.
the product(s) is/are damaged due to battery leakage.
For the latest information on NITECORE® products and services, please contact
a local NITECORE® distributor or send an email to
service@nitecore.com
All images, text and statements specified herein this user manual are for
reference purposes only. Should any discrepancy occur between this manual and
information specified on www.nitecore.com, Sysmax
Innovations Co., Ltd. reserves the right to interpret and amend the content of
this document at any time without prior notice.
SYSMAX Innovations Co., Ltd.
TEL: +86-20-83862000
FAX: +86-20-83882723
E-mail: info@nitecore.com
Web: www.nitecore.com
Address Rm 2601-06, Central Tower, No.5 Xiancun Road,
Tianhe District, Guangzhou, 510623, Guangdong, China
Please find us on Facebook: NITECORE Flashlight
Thanks for purchasing NITECORE!
Made in China BR27122521
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>