RADWIN AP0263510 5 GHz SU/Alpha Assembly Boards User Guide
- June 6, 2024
- RADWIN
Table of Contents
AP0263510, AP0263530, AP0263540
5 GHz SU/Alpha Assembly Boards
REFERENCE GUIDE
Regulatory Compliance
FCC/ISED – Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and ISED RSS standards. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Warning
It is the responsibility of the installer to ensure that when using the
outdoor antenna kits, only those antennas certified with the product are used.
The use of any antenna other than those certified with the product is
expressly forbidden by FCC rules 47 CFR part 15.204 and ISED RSS standards.
Caution
Outdoor units and antennas should be installed ONLY by experienced
installation professionals who are familiar with local building and safety
codes and, wherever applicable, are licensed by the appropriate government
regulatory authorities. Failure to do so may void the product warranty and may
expose the end-user or the service provider to legal and financial
liabilities. Resellers or distributors of this equipment are not liable for
injury, damage, or violation of regulations associated with the installation
of outdoor units or antennas. The installer should configure the output power
level of antennas according to country regulations and antenna type.
Warning
The antennas used for this transmitter must be installed to provide a
separation distance of at least 24 cm from all persons
Warning
The module is granted to operate under FCC certification in the 5.2 / 5.3 /
5.4 / 5.8 GHz bands.
This device complies with Part 15 of the FCC rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada
Overview
The AP0263510, AP0263530, AP0263540 is a 5 GHz assembly board operating in the 5.2, 5.3, 5.4, and 5.8 GHz frequency bands. It is a TDD OFDM radio supporting 10, 20 MHz, 40 MHz, and 80 MHz channel bandwidths. It is a 2×2 MIMO transceiver.
The assembly board contains the power supply block, the CPU and peripheral block, the Ethernet communication interface, and the radio transceiver block on a single board. It is installed in a host enclosure manufactured by RADWIN.
The 5 GHz assembly board is certified as a limited modular approval type under the FCC ID: Q3K-SXSUALMOD. It is also certified under IC: 5100A-SXSUALMOD excluding the 5.2 GHz band.
Condition of Use
The AP0263510, AP0263530, AP0263540 5 GHz assembly board is a proprietary radio module manufactured by RADWIN. The module is not for sale to the general public or for installation in hosts not manufactured by RADWIN.
FCC rules and ISED Regulation Restrictions
The host firmware is factory programmed to operate under the FCC rules and ISED regulation restrictions. The firmware is locked and inaccessible by any third party. As a result of the above, the user interface allows both the installer and the user to control the host only within the boundaries of the regional restrictions.
Part 15 Subpart B disclaimer
The AP0263510, AP0263530, AP0263540 5 GHz assembly board is the only FCC
authorized for FCC rules Part 15E.
The final hosts into which the assembly boards have been installed were tested
to Part 15 Subpart B.
The final hosts are:
- SU Integrated
- Alpha Integrated
- SU Connectorized
- Alpha Connectorized
Antennas
The AP0263510, AP0263530, AP0263540 5 GHz assembly board is certified with a wide range of antenna types covering both Point-to-Point and Multipoint systems up to 32 dBi gain.
Antennas
Following is the list of antennas supported by the 5 GHz SU/Alpha boards:
Antenna Type| Manufacturer| Model Number| Antenna Gain
(dB)
---|---|---|---
Flat Panel Dual Pole External| RADWIN| RW-9105-5159| 13
Flat Panel Dual Pole External| RADWIN| RW-9105-4958| 16
Flat Panel Dual Pole Integrated| RADWIN| MR0204670| 22
Flat Panel Dual Pole External| RADWIN| RW-9613-4960| 23
Flat Panel Dual Pole Integrated| RADWIN| MT0268450| 25
Flat Panel Dual Pole External| RADWIN| RW-9622-5001| 28
Dual Pole Dish| RADWIN| RW-9721-5158| 28
Dual Pole Dish| RADWIN| RW-9732-4958| 32
Maximum Output Power
5725 – 5850 MHz band – FCC Part 15 Subpart E, RSS 247
The maximum output power is set as follows, under FCC and ISED regulations.
The power values are for PtP systems with 13 dBi antenna gain. The highest
conducted output power shall be limited on all channel bandwidths as per the
table below
10 MHz: 28.0 dBm
20 MHz: 28.0 dBm
40 MHz: 29.0 dBm
80 MHz: 28.0 dBm
5150 – 5250 MHz band – FCC Part 15 Subpart E
The maximum output power is set as follows, under FCC regulations. The
power values are for PtP systems with 13 dBi antenna gain
10 MHz: 26.0 dBm
20 MHz: 29.0 dBm
40 MHz: 29.0 dBm
80 MHz: 18.0 dBm
5250 – 5350 MHz band – FCC Part 15 Subpart E, RSS 247
The maximum output power is set as follows, under FCC and ISED regulations.
The power values are for systems with 13 dBi antenna gain not exceeding the 30
dBm EIRP limit
20 MHz: 17.0 dBm
40 MHz: 17.0 dBm
80 MHz: 17.0 dBm
5470 – 5725 MHz band – FCC Part 15 Subpart E, RSS 247
The maximum output power is set as follows, under FCC and ISED regulations.
The power values are for systems with 13 dBi antenna gain not exceeding the 30
dBm EIRP limit
20 MHz: 17.0 dBm
40 MHz: 17.0 dBm
80 MHz: 17.0 dBm
Labeling Requirements
The assembly board is labeled with the identification numbers as follows:
FCC ID: Q3K-5XSUALMOD
IC: 5100A-5XSUALMOD
The host into which the assembly board is assembled is labeled as follows:
Contains FCC ID: Q3K-5XSUALMOD
Contains IC: 5100A-5XSUALMOD
Hosts Test Mode Configuration
Integration in various hosts requires power limitations per antenna assembly gain used with the host to comply with the FCC/ISED requirements (5.15-5.25 GHz only for FCC)
Host| Antenna Gain (dBi)|
Max Output Power per Band
(dBm, Glitz)
---|---|---
5.15-5.25| 5.25-5.35| 5.47-5.725| 5.725-5.85
SU Connectorized and Alpha Connectorized| 13| 29.0| 17.0| 17.0| 29.0
SU Connectorized and Alpha Connectorized| 16| 26.0| 14.0| 14.0| 26.0
SU Integrated and Alpha Integrated| 22| 23.0| 7.0| 7.0| 27.0
SU Connectorized and Alpha Connectorized| 23| 22.0| 8.0| 8.0| 26.0
SU Connectorized and Alpha Connectorized| 25| 20.0| 5.0| 5.0| 24.0
SU Connectorized and Alpha Connectorized| 28| 15.0| N/A| N/A| 15.0
SU Connectorized and Alpha Connectorized| 32| 10.0| N/A| N/A| 13.0
AP0263510/..30/..40 Reference Guide
Documents / Resources
|
RADWIN AP0263510 5 GHz SU/Alpha Assembly
Boards
[pdf] User Guide
5XSUALMOD, Q3K-5XSUALMOD, Q3K5XSUALMOD, AP0263510, AP0263530, AP0263540,
AP0263510 5 GHz SU Alpha Assembly Boards, 5 GHz SU Alpha Assembly Boards
---|---
|
RADWIN AP0263510 5 GHz SU/Alpha Assembly
Boards
[pdf] User Guide
AP0263510 5 GHz SU Alpha Assembly Boards, AP0263510, 5 GHz SU Alpha Assembly
Boards, SU Alpha Assembly Boards, Alpha Assembly Boards, Assembly Boards,
Boards
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>