Wise Ally Holdings AP83 Rapid Response Button User Guide
- June 6, 2024
- Wise Ally Holdings
Table of Contents
AP83 Rapid Response Button
Rapid Response Button User Guide
The Rapid Response Button is designed to improve employee safety by providing
indoor location information of employees upon emergency leveraging PwC’s
Indoor Geolocation Platform (IGP).
(1) Lanyard Ring
(2) Left Button with LED (4) USB Port and Reset Pin
(5) Recessed Area for Badge
(3) Right Button
Reserved for back image of the Device
(4a) Reset Pin (4b) USB Charging Port
(6) Device Label
(7) USB Charging Cable
(1) Lanyard Ring
Attach lanyard with the ring to wear the device
(2) Left Button with LED
The left button is smooth and translucent with LEDs inside it
(3) Right Button
The right button is orange and textured
Trigger / Stop Alerts Press and hold both the left button and the right button
to trigger alerts and location reports. The LED will flash when an alert is
triggered.
Press and hold both buttons again to stop alerts.
Silent / Audible Alert Mode
When the silent alert mode is triggered, the device will vibrate once and the
LED will flash green. Once a location report is sent, the device will vibrate.
When the audible alert mode is triggered, the device will beep and the LED
will flash red. Once a location report is sent, the device will vibrate.
Device Specs:
Model: AP83 SigFox Radio Frequency Band: 902.1375MHz to 904.6625MHz WiFi Band:
2.4GHz Bluetooth Version: 4.2
If an alert is triggered and not stopped, the device will send a location
report every one minute
Check Silent / Audible Alert Mode
Press and release the right (orange) button. If the LED flashes green, the
device is in the silent alert mode. If the LED flashes red, the device is in
the audible alert mode
Switch Between Silent / Audible Alert Modes
Press and hold the right (orange) button for 3 seconds to switch between
silent / audible alert modes
The device will beep and flash green LED when it is switched to the silent
alert mode
The device will beep and flash red LED when it is switched to the audible
alert mode
(4) USB Port and Reset Pin
(4a) Micro USB Port for charging and device update (by device managers)
(4b) Reset pin. Device can be power cycled by pressing the reset pin with a
paperclip
(5) Recessed Area for Badge
Optionally stick an employee badge photo in the recessed area
(6) Device Label
DevEUI: LoRa Device Extended Unique Identifier
Address: Device MAC address Serial No. Device serial number Part No. Device
part number FCC ID: Device FCC ID QR Code: Scanning of the QR
code renders a concatenated DevEUI, Address, Serial No. and Part No.
(7) USB Charging Cable
Charging Micro USB cable for the device
Dimensions: 2.6 x 4.5 x 0.4 inch Weight: 62g Battery: 500mAh Operating Temperature: 0-45C Relative Humidity: 0-95%
Rapid Response Button User Guide
Caution: The user is cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment. Note: This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna. –Increase the separation between
the equipment and receiver. –Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. –Consult the dealer or
an experienced radio/TV technician for help.
This equipment complies with FCC`s RF radiation exposure limits set forth for
an uncontrolled environment. End user must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not
be co-located or operating in conjunction with any other antenna or
transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>