eta BLENDIC II Table Nutri Blender Instructions

eta BLENDIC II Table Nutri Blender

INSTRUCTIONS FOR USE

Dear customer, thank you for purchasing our product. Please read the operating instructions carefully before putting the appliance into operation and keep these instructions including the warranty, the receipt and, if possible, the box with the internal packing.

SAFETY WARNINGS

• Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.
• Check whether the data on the type label correspond with the voltage in your socket. The power supply plug has to be connected to a socket of electrical installation that conforms to respective standards.
• Never use the appliance if the power cord or power plug are damaged, if it is not functioning correctly or if it has fallen on the floor and been damaged or if it has fallen into water. In such cases take the appliance to a professional service centre to verify its safety and correct function.
• This appliance must not be used by children. Keep the device and its supply cord out of reach of children. The device may be used by persons with reduced physical or mental abilities or lack of experience and knowledge only if they are under
• supervision or they have been instructed about using the appliance safely and understand the potential dangers. Children must not play with the appliance.
• Be careful when pouring hot liquid into the food processing device or the mixer because it may spurt out of the appliance because of sudden boil.
• If the power cord of this appliance is damaged, the cord must be replaced by the manufacturer, their service technician or by a similarly qualified person, this will prevent the creation of a dangerous situation.
• Always unplug the appliance from power supply if you leave it unattended.
• Before replacing accessories or accessible parts, which move during operation, before assembly and disassembly, before cleaning or maintenance, turn off the appliance and disconnect it from the mains by pulling the power cord from the power socket!
• Be careful when handling the blender, the knife is very sharp!
• CAUTION: Do not use the appliance with a program, time switch or any other part that turns the appliance on automatically as there is a risk of fire if the appliance is not covered or placed properly.
• When the appliance is in operation, prevent pets, plants or insects to get in contact with it.
• Every time before the propulsion unit is switched on, the container needs to be attached properly.
• Never remove or attach the container while the propulsion unit is in operation. Thus you avoid the risk of injury or damage to the appliance.
• Maximum time of processing is 2 min. After that, keep the break for 3 min necessary for the motor unit to cool off.
• The appliance is equipped with thermal safety fuse which disconnects current supply incase of engine overloading. If it occurs, unplug the appliance and let the appliance getcooled at least 10 minutes.
• After finishing work and before cleaning, always switch off the appliance and disconnect it from power supply by taking the power cord connector out of the electric socket.
•  The product is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!
• not place any objects on the appliance.
• This appliance is not intended for outdoor use.
• The appliance must not be used in damp or wet environment and in any environment with the danger of fire or explosion (spaces where chemicals, fuels, oils, gases, paints and other flammable or volatile materials are stored).
• Correctly placing the bowl on the appliance will release the safety lock and the appliance may be turned on.
• Every time before the propulsion unit is switched on, the container needs to be attached properly.
•  Never leave the appliance unsupervised and check it during the whole time of preparing meals!
• Never immerse the drive unit into water and do not wash it in running water!
•  Do not switch on the appliance without ingredients put in!
• Before removing container, let the rotating part stop.
• Before preparation, remove possible packages from food (e.g. paper, a PE bag, etc.).
• Do not process ingredients of higher temperature than approx. 80 °C.
• If the processed ingredients start to stick on the accessory (e.g. the knife or blender dish), turn the appliance off and clean carefully with a spatula.
• Use the mixer only in its working position and at places where there is no risk of tipping and in sufficient distance from heat sources (e.g. heater, stove, cooker, grill etc.) and wet surfaces (sinks, basins etc.)
• Use the appliance only with accessory intended for this type of device. Using other accessory may pose danger for the user.
• Do not insert the appliance into any body holes.
• Check the condition of the power cord of the appliance regularly.
• Prevent the supply cord to hang loosely over the edge of the working desk where children could reach it.
• If you need to use an extension cord, it has to be uncorrupted and it has to comply with the valid standards.
• The power cord must not be damaged with sharp or hot objects, open fire, it must not be sunk into water or bent over sharp edges. Never put it on hot surfaces or do not let it hang over the edge of a table or work tables. Hitting, stumbling or pulling the power cord. by children can result in tilting over or drawing the appliance down and serious injury!
• Use the appliance only with original accessories from the manufacturer.
• Use the appliance only for the purpose it is intended for as specified in this manual. Never use the appliance for any other purpose.
•  WARNING: There is a risk of injury in case of incorrect use (not in accordance with the manual) of the appliance.
•  The manufacturer is not responsible for damage and injuries caused by improper use of the appliance and the accessories (e.g. food deterioration, injury, cutting) and its guarantee for the appliance does not apply in situations when the safety warnings above are not complied with.

FEATURES OF THE DEVICE

• A – propulsion unit
  • A1 – propulsion shaft
  • A2 – button On/Off and program “MIX”  A3 – button “PULSE” program A4 – supply cord
• B – bowl 500 ml / 700 ml
  • B1 – seal
  • B2 – plastic container base  B3 – knife
• C – travel lid
  • C1 – lid plug    C2 – seal
  • Attachments for the respective ETA models:

Type / Acessories| B (500 ml)

(ETA401194000)

| B (700 ml)

(ETA401193000)

| C
---|---|---|---
ETA 4011-20| √ (2 x)| √ (2 x)| √ (4 x)
ETA 4011-30| √ (1 x)| √ (1 x)| √ (2 x)
ETA 4011-41| √ (1 x)| –| √ (1 x)

• Included
• Not included

PREPARATION FOR USE

Remove all packing material and take out the blender. Remove all possible adhesion foils, stick-on labels or paper from the appliance. We recommend washing the container before using it for the first time. The knife section is treated with oil not harmful to health for technological reasons. Therefore first fill in the container with warm water (max. 50 °C) with a small amount of detergent. Hold the knife (on the bottom) at the plastic base and slide
it (with the blade down) to the hole in the filled container, then turn it in the direction of the maximum position. Then put the container on and run for 15 sec. Then rinse the container and knife with clear water. Before the first use, wash the other parts that will be in contact with food in hot water with a detergent, rinse thoroughly with clean water and wipe till dry, or let dry the knife section is treated with oil not harmful to health for technological reasons. Put the blender on a flat, stable, smooth and clean work surface at the height of at least
85 cm, out of reach of children and incapacitated people. Make sure that the power cord is not damaged and that it does not lead through any sharp or hot surfaces. Plug power supply fork to the electric power. Possible short-time mild smoke when the appliance is operated for the first time is not a defect and the appliance is not subject to a complaint for this reason.

Warning

• If the dish is not fitted correctly on the propulsion unit, the safety switch will not allow to put the motor in operation. The standby mode is indicated by the signal lights.
• When the blender is in the state of idle operation, e.g. the blade fails to touch the foods, unplug the unit until the foods have been relaxed.

ACCESSORY INSTALLATION

Warning

•  Maximum time of operation is 60+60 sec.,., then the appliance rest and cool down for 3 min. and will not work. If you process big amounts of food, divide them in separate portions so that you keep) recommended times of operation and rest of the propulsion unit.

Bowl assembly and distribution (B)
Put sealing B1 on the contact surface of the plastic base of container B2. Hold the knife (on the bottom) at the plastic base and slide it (with the blade down) to the hole in the filled container B, then turn it in the direction of the maximum position and tighten with reasonable force. Remove the knife from the container in the opposite direction.

Warning

•  Check whether the sealing is put properly on its place in the bowl, is clean and is not leakage of fluid.

Attaching and removing the bowl (B)
Mount the bowl B on drive A1 so that it slides down, then secure it by turning it clockwise till you hear a snapping sound (at the same time, safety lock is unlocked). Pay special attention to this operation. You can remove the bowl in the opposite direction.
Control panel
Buton (A2) to start/end the processing program 1
Start the drive by pushing the button. Stop the drive by pushing the button or the appliance turns off automatically after 1 minute.

• During the blending the speed is reduced two times (approximately for 5 seconds) for better mixing of raw materials. This is normal situation and does not form the reason for warranty claim.
•  If you are not satisfied with the result, you can continue the mixing by pressing button A3, switch off the appliance, mix the ingredients with spatula, take some part of the ingredients or add a little liquid.

Buton (A3) to start processing programme “PULSE”

Start the drive by pushing the button (the motor runs only for the time when the button is pushed). While processing, we recommend using the pulses of operation. One pulse is 5 seconds at maximum. Process the foodstuffs as long till you will be satisfied with the result (the appliance turns off automatically after 1 minute).

Lights signaling

• the indicator light is off: the blender is off,
• the indicator lights is flashing: the blender is in standby state,
• the respectively indicator permanent light: the blender is on,
• Both control lights are on: the blender is turned off and the time for cooling down of the motor is running.

USING THE BLENDER

The blender is perfectly for preparation fresh fruit drinks, fitness & protein drinks, milkshakes, mixed alcoholic & non-alcoholic beverages, smoothies, but also for crushed ice. Excellent for salsa sauces snack for children, etc.. After mounting of the assembled blending bowl on the drive unit and after its filling with Ingredients. Check whether is not leakage of fluid from containers. Plug power supply fork A4 to the electric power and control.

WARNING: To activate press and hold (approx 3 sec.) the A2 button. The blender is switched automatically to the stand-by regime is indicated by the indicators coming o flashing. When working, hold with one hand the driving unit and press the switch with the other hand. Choose the amount of the processed food so that the maximum volume of the containers marked with the gauge line is not exceeded. Bigger amount of processed food has to be divided into several doses and the volume of the containers has to be checked regularly. Always set the program with regard to the kind and amount of ingredients being processed, and particularly with regard to ripeness of fruit and vegetables. Select the required processing program by A2 – A3 buttons. We recommend stopping work from time to time, switching off the appliance and removing possible food that was stuck onto the knife or containers. After finishing work, disconnect the appliance from power supply by taking the connector of power cord A4 out of the electric socket. Unscrew the plastic container base B2 and replace it with the jar travel cover C. If you open the cap C1, you can drink directly from the jar.

Recommendation

• It is recommended to cut tough ingredients into small pieces. Do not process very hard materials (e.g. cinnamon,, spices, , nutmeg,, turmeric, , bean coffee or only ice cubes etc.)! The knife would be blunt soon.
• Nuts, and cheese will chop / grind better if thoroughly chilled first.
• Hard ingredients (e.g. legumes, soya beans, etc.) should be soaked in water before processing.
• The longer you process the food with the mixer, the smoother the result will be.
• If you prepare a small amount of ingredients for beverages, doughs or purees, it is recommended to pour a small amount of liquid in the container before you start mixing
• Sometimes during processing, the ingredients clump together. If this happens, remove the cup from the motor unit and shake it. Refit the cup to the motor unit and carry on processing.
• The inner side of the container might change colour (become matt) and the container might give out a characteristic smell in the process with hard ingredients but this does not affect the function of the appliance and it is not a reason for a claim. Therefore we recommend using the same container for processing hard ingredients

PROCESSING GUIDE FOP DISH

Food| Maximum amount| Approximate time (seconds)| Preparation (cm)
---|---|---|---
Children‘s food, soups, sauces| 100 – 400 ml| 60| –
Shakes and cocktails| 100 – 500 ml| 50| –
Food and vegetables| 100 – 300 g| 30| 2 x 2 x 2
Ice cubes with water| max. 5 pcs| 30| 1.5 x 1.5 x 1.5

STORAGE

Store the appliance and acessories after cleaning at a dry, dustfree and

safe place, out of reach of children and incapacitated people.MAINTENANCE

Do not use rough and aggressive detergents! Clean drive unit A with a soft and wet cloth with a little detergent. Make sure that water does not get inside the appliance! Wash the accessories in hot water with a detergent right after use, rinse it in clean water and wipe till dry (you can also wash the accessories in a dishwasher). Knife cleaning procedure: pour about 0.3 l of clear water in the container, switch on the appliance and remove the impurities by several pulses. In the case of larger amount of impurities, repeat the procedure several times, or pour 0.3 litre of water, add a small amount of detergent and switch on the blender for 15 sec. Be very careful when cleaning the knife! Make sure that the cutting edges of the accessories are not in contact with hard objects that make them blunt and thus they reduce their effectiveness. If sealing B1, C2 is worn out or damaged, replace it with a new one (of a similar type). Some food can colour the accessories in some way. But this does not affect the function of the appliance and it is not a reason for a claim. This colouring usually disappears after some time. Never dry plastic moldings over a heat source (e.g. heater, electric / gas stove).
Please make sure that the contact surface and sealing elements are clean, undamaged and properly placed.

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for production of packing, components and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electric or electronic products must not be disposed of together with municipal waste. For proper disposal of the product, hand it over at special collection places where it will be taken over free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Ask for more details at the local authorities or in the nearest collection site. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. If the appliance is to be put out of operation for good, after disconnecting it from power supply we recommend cutting off the power cord and thus it will not be possible to use the appliance again.

More extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by professional service!
Failure to comply with the instructions of the manufacturer will lead to expiration of the right to warranty repair!

TECHNICAL DATA

• Voltage (V)                                        shown on the type label of the appliance
• Input (W)                                          shown on the type label of the appliance
• Container volume (mI) about            500 / 700
• Weight (kg) about                                3
• Protection class of the appliance         II.

Inputin in off mode is < 1.0 W.
Noise level: Acoustic noise level of 80 dB (A) re 1pW
The manufacturer reserves the right to change the technical specifications and accessories for the respective models.
WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING OR IN THE INSTRUCTIONS MANUAL: HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS.
TO AVOID THE DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

Documents / Resources

| eta BLENDIC II Table Nutri Blender [pdf] Instructions
BLENDIC II, Table Nutri Blender, BLENDIC II Table Nutri Blender, Blender
---|---

References

• AEG Hausgeräte | Setzen Sie auf Qualität | AEG
• ElektroEko – Odbiór odpadów elektro
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>