legrand WNRL43 Wake-Sleep Wireless Smart Switch Installation Guide
- June 6, 2024
- Legrand
Table of Contents
legrand WNRL43 Wake-Sleep Wireless Smart Switch Installation Guide
Catalog Number(s)
Country of Origin: Made in China
REGULATORY INFORMATION
FCC NOTICE: This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 90 mm between the transmitter’s radiating structure(s) and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly
approved by the manufacturer will void the warranty and the user’s authority
to operate the equipment.
Contains FCC ID: 2AU5D-WNZED
IC NOTICE: This device complies with Industry Canada licenseexempt RSS
standards. Operation is subject to the following two conditions: (1) this
device may not cause interference; and (2) this device must accept any
interference, including interference that may cause undesired operation of the
device.
RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits
given in RSS-102 Issue 5 requirements at the minimum separation distance of 90
mm to the human body. Note: Any changes or modifi cations to this device that
are not expressly approved by the manufacturer, will void the warranty and the
user’s authority to operate the equipment.
IC: 25764-WNZED
HVIN: WNRL43
BEFORE YOU START
Review this guide in its entirety. Consult an electrician with any questions or if you are unsure of your abilities.
WARNING: Incorrect installation could result in death, serious injury,
and/or
damage to your home or devices.
CAUTION: To reduce the risk of injury and/or overheating and damage to
other equipment:
- For dry, indoor use only.
- Do not use to power medical equipment – not suitable as a disconnecting means.
WHAT YOU NEED
Required:
- Phillips-head screwdriver
- Flat blade screwdriver
You May Also Need:
Voltage tester, pliers, wire cutter, wire stripper, electrical tape, and wire
nut.
INSTALLATION
-
Choose a place to install the device
This device can be installed on a flat wall surface or in any standard U.S. electrical wall box. It may also be installed over the wall next to a standard U.S. electrical wall box, if used with a multi-gang Legrand Radiant wall plate, catalog number beginning with RWP26-XXX.
INSTALLATION (on a wall surface) -
Use provided double sided stickers to install on a tiled or other smooth surface. Markings on the back of the device indicate location for the stickers.
-
Use provided mounting screws to install on dry wall or uneven surface where the sticker may not work. Do not remove label or pull out ground wire as device may not sit flush.
INSTALLATION (in an electrical box)
2. Turn off power to the box at circuit breaker.
Note: Ensure power is off to all devices in the electrical box. Remove old
device from box. Install wire nuts to terminate all the exposed wires that
were previously connected to the old device. Ensure complete electrical
insulation by securing the wire nuts making sure no bare wire is exposed.
3. Install and secure the device
a. Fold the wires into the electrical box, taking care not to pinch a wire.
b. Remove label on back of the device to expose ground wire and connect it to
the box ground.
c. Use included mounting screws to secure the device to the electrical box.
INSTALLATION (NEXT TO AN ELECTRICAL BOX)
2. Break off the tabs on device
Break off the tabs at the top and bottom of the device using pliers as shown
in image.
Mark the location of the device on the wall surface to the left or right of
existing device(s) installed in the electrical box by visually aligning it
with existing device(s)
3. Install and secure the device
a. Fold the wires into the electrical box, taking care not to pinch a wire.
b. Remove label on back of the device to expose ground wire and connect to the
box ground. Secure the connection with wire nut.
c. Use double sided stickers to install on tiled or any other smooth surface
next to the electrical box.
d. Use provided mounting screws if the surface next the electrical box is dry
wall or uneven surface where the sticker may not work.
e. Install the multi-gang subframe using sub-frame screws provided with the
radiant wall plate.
f. Snap-on the radiant wall plate.
If installing with a non-radiant wall plate, skip steps “e” and “f” above and
use screws provided with the other wall plate to secure this device.
SETUP
Remove battery insulation tab as shown in the image.
4. Set Up Your System
a. Download and launch the Legrand Home + Control app. The app is available on
the App Store or on Google Play.
b. Connect your smart device to your home network by following the step by
step instructions in the app.
c. Use the app to control your smart device.
For the most recent instruction sheets or more information on this product,
please see this link or scan the QR code: https://www.legrand.us/p/wnrl43wh
GETTING TO KNOW YOUR BATTERY POWERED SWITCH
LED Indicator Light Explanations
Reset To Factory Default
Deleting a device from the app will reset it to factory defaults.
To manually reset the device to factory defaults press and hold the EZ button
for 15 seconds until you see the LED blink green and red then release. The LED
will turn off when the reset is complete.
Legrand reserves the right to change specifications without notice.
LIMITED ONE YEAR WARRANTY
Legrand will remedy any defect in workmanship or material in Legrand products
which may develop under proper and normal use within one years from date of
purchase by a consumer:
(1) by repair or replacement, or, at Legrand’s option, (2) by return of an
amount equal to consumer’s purchase price. Such remedy is IN LIEU OF ANY AND
ALL EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Such remedy by Legrand does not include or cover cost of
labor for removal or reinstallation of the product. ALL OTHER FURTHER ELEMENTS
OF DAMAGE (INCIDENTAL OR CONSEQUENTIAL DAMAGES) FOR BREACH OF ANY AND ALL
EXPRESSED OR IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED HEREBY. (Some states do not
allow disclaimers or exclusion or limitation of incidental or consequential
damages, so the above disclaimer and limitation or exclusion may not apply to
you.) ANY IMPLIED WARRANTIES INCLUDING WHERE REQUIRED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE
one YEAR PERIOD SET FORTH ABOVE. (Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you.)
To ensure safety, all repairs to Legrand products must be made by Legrand, or
under its specific direction. Procedure to obtain performance of any warranty
obligation is as follows: (1) Contact Legrand, Syracuse, New York 13221, for
instructions concerning return or repair; (2) return the product to Legrand,
postage paid, with your name and address and a written description of the
installation or use of the Legrand product, and the observed defects or
failure to operate, or other claimed basis for dissatisfaction. This warranty
gives you specific legal rights and you may also have other rights which vary
from state to state.
For covering patents, see www.legrand.us/patents
Questions? We’re here to help.
Phone: 1-877-833-3303 8:00 a.m. to 8:00
p.m. EST (M-F)
Email: smartlighting@legrand.us
Chat: https://www.legrand.us/radiant/smart-lighting.aspx
(Click on the chat icon to open a dialogue box)
No: 341331 4/21
© Copyright 2021 Legrand All Rights Reserved.
800.223.4185
1.877.BY.LEGRAND
www.legrand.us
www.legrand.ca
Read More About This Manual & Download PDF:
References
- Patents | Legrand
- radiant® Sleep/Wake Wireless Smart Switch with Netatmo, White | Connect Directly with Netatmo | Smart Lighting | Wiring Devices
- Smart Lighting from the radiant Collection ⎸Legrand
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>