KIDSJOY H9 Diy Unloading Into Door Drone User Manual

KIDSJOY H9 Diy Unloading Into Door Drone

Watch Gesture Remote ControlTechnical Parameters

• Battery Capacity: 3.7v 150mAh
• Charging time: 30 minutes
• Using time;10 hours
• After the remote control stays at the stand by for 1 minute, then it will shut down automatically.
• When the remote control goes into low voltage, the indicator light will flash slowly. Under this circumstance, the machine cannot be used. It should be charged.

UAV Parameters

• Length:155.0mm
• Width:113.5mm
• Height:36mm
• Battery Capacity: 3.7v 500mAh
• Charging time: 90 minutes
• Flying time: more than About 10 minutes
• Remote control distance: 80 meter

Thank you for purchasing our company’s product. In order to use the product correctly and ensure your own safety, please read this operation manual carefully before you use the products. Besides, please keep it well for future reference. If the picture in this operation manual does not match with the actual product, please refer to the actual product.

Get to know about your remote control

Conventional remote control

1. Fast and slow gear: The default for booting is 1 gear, press once for 2 gears “drip” twice; press again for 3 gears “drip” three times; press again for 1 gear “drip” once, repeat this cycle.
2. Obstacle avoidance mode: Press the function key to enter the obstacle avoidance mode, when the aircraft fuselage encounters obstacles, the aircraft will fly in the opposite direction, press it again to exit.(only the left and right have obstacle avoidance, not the front and back)
3. Gas rod: control the UAV to rise/fall, and turn left/right.
4. High-speed rotation: Press the function key and the aircraft will rotate at high
5. One-click take-off/emergency stop: A short press is for the aircraft to take off automatically, press for more than two seconds, and the aircraft stops immediately. During the flight of the aircraft, a short press is one-click to land.
6. Headless mode: With a short press of the function key, “drip” once, the indicator light of the UAV changes from constant light to flashing state, and the UAV enters the headless mode; after the UAV successfully enters the headless mode, short press the function button, and with a sound of “drip”, the indicator light of the UAV changes from flashing to constant bright state, and the UAV exits the headless mode; (after entering the headless mode, no matter where the UAV is facing, only the front before entering the headless mode is regarded as the front).
7. Tumble: Press the function key to enter the tumbling state, and the handle controls the tumbling direction.
8. When without operation, the aircraft is moving forward/backward automatically,then press button-8/10tomaketheflightstaystill.
9. Direction lever: Control the left, right, front and rear directions of the aircraft.
10. When without operation, the aircraft is moving left/right automatically, then press button-11/12tomaketheflightstaystill.

Accessories Table

Diagram for changing fan

Operation manual for normal remote control

Powering up the UAV

1. Assemble the battery into the battery slot on the bottom of the UAV to make sure that the battery is in the correct place.(Figure1)
2. Plug the power connector on the battery into the power connector on the bottom of the UAV.(Figure2)

Remote Control and UAV Pairing

A ft er connecting the UAV with electricity, turn on the remote control.Pushthegasrodtothehighest positionandthenpullittothelowestpositionand thenreleaseit.WhentheLEDlightoftheUAV changes from flashing to always-on,then it means that the UAV and the remote control have been successfully synchronized.

One Button Taking off

After the synchronization, short press the button, Taking off“. Then the fans of UAV will start to rota te. The UAV will automatically take off to a height of 1.2 meters.

In the hand throwing induction mode

Plug in the battery plug and put the aircraft on the ground. After the indicator light changes from fast flash to slow flash, pick up the aircraft and throw it out in parallel. The aircraft will hover in the air again. At the same time, the aircraft enters the obstacle avoidance mode. After sensing the obstacles, the aircraft will fly in the opposite direction. To make pairing with remote control, turn on the remote control, push the gas rod the highest position then pull it to the lowest position and release it, then quickly move the steering rod to control the aircraft. otherwise, the UAV will fall down. After successful pairing, it will exit the hand throwing mode. you need to restart the UVA to enter hand toss mode.

UAV Calibration

When UAV flight is unstable, When the synchronization is complete, place the UAV in a horizontal position and push the gas rod down 45 degree. Then push the gas rod to the right down 45 degree in order to complete UAV calibration. The two LED lights of the UAV will start to flash, it means that the calibration is in processing. When the LED light stops flashin g, it means that the calibration is successful fini shed.

Operation guidance for steering during flying Steering operation

Remote Control Battery Mount

Insert 3 AA batteries correctly according to the electrode instructions (batteries to be purchased separately), and then replace the battery cov er with a new one.

Caution

1. The positive and negative terminals of the bat tery must be identified when installing the batt ery, and must not be reversed.
2. Do not mix old and new batteries.
3. Do not mix different types of batteries.

UAV Battery Charging

Connect the battery to the charger socket, and t hen sow the USB port of the charger into the US B port of the laptop. The red light goes out when the battery is charging and light off when the b attery is fully charged.

Get to know about your remote control

Main button

1. First time short press to power up.
2. Second time short press of the reset button for taking off.
3. During flight, short press the butt on, then is the slow landing function.
4. Press and hold 1 second to stop and 3 seconds to turn off the machine.

Finger Button

1. First time short press for taking off to 1.2 meters
2. During flight, short press the button to enter the tumbling state,and turn hand left/right/forward/ backward to control the tumbling direction.
3. During flight, press three times quic kly to enter IR avoidance mode.
4. Long press is switch between (gas and steering)

Attention:

Obstacle avoidance sensing distance is around 1.2 meter. When the machine enters intoobstacle avoidance mode, it is forbidden to make the machine go into the space where is smaller than 1.2 meter.

Accessories Table

Diagram for changing fan

Flying preparation of watch remote control

Place the UAV flat on the grou nd and plug in the battery, then the light will change from flashi ng fast to slow when the UAV is turned on. Indicates waiting for coding

Press the gravity sensing rem ote control power switch briefl y, the remote control light blin ks slowly 3 times and then tur ns on normally, indicating the end of coding. The indicator li ght willchange from slow flash to long light, which means the coding successful.

Start flight, short press the re mote control finger button, the UAV takes off to 1.2 meters.

Operation manual for watch remote

While the UAV is in flight, press and hold the remote control finger button. When the fist is lifting up, the UAV will fly up. When the fist is moving down, the UAV will fly down.

While the UAV is in flight, press and hold the remote control finger button. When the fist is turning left, the UAV will turn left. When the fist is turning right, the UAV will turn right.

While the UAV is in flight, release the remote control finger button. When the fist is lowing down, the UAV will go forward. When the fist is lifting up, the UAV will go backward.

When the UAV is in flight1. While the UAV is in fli ght, release the remote control finger button. W hen the fist is turning left, the UAV will fly to left. When the fist is turning right, the UAV will fly to right.

IR obstacle avoidance mode

By default, the UAV does not have an IR obsta cle avoidance function when the UAV is turned on. When in flight, press the finger button three times quickly and the UAV indicator will flash th ree times to activate the IR avoidance mode. P ress the finger button three times quickly to exit the IR obstacle avoidance mode. (Only left and right obstacle avoidance, no front and back).

Rollover function

Press the finger button of the remote control briefly in flight, the indicator light flashes, and the remote control is tilted in four directions to realize the rollover function in the corresponding direction. When there is no movement of the remote control for 2 seconds, then the roll function will exit.

Slow decline

Press the main button of the remote control briefly during the flight, the UAV slowly descends to the ground and stops flying. 2. Rollover function 3. Slow decline Note: The sensing distance is 1.2 meters, please do not operate in a space smaller than 1.2 meters.

Emergency stop function

If you can’t control the UAV during flight, press and hold the main button of the remote control for 1 second to stop the UAV immediately.

Low voltage protection for flight instruments

When the UAV enters the low voltage protection, the UAV light will flash slowly, and then slowly descend to the ground and stop flying after about 30 seconds Note: Press and hold the UAV po wer button for 1 second to turn off the UAV and press the gravity-sensing remote control main button for 3 seconds to turn off the UAV.

Maintenance and Repairment

1. Use a clean, soft cloth to clean this product.
2. Avoid exposing this product to sunlight or heat.
3. Do not immerse the product in the water because this may lead to electronic components.
4. Please regularly check the plug and other accessories. If any there is any damage, please stop using the UAV immediately until it is completely repaired.

Security Rules

1. Keep small parts of the UAV out of the reach of small children in order to avoid accidents.
2. This UAV has full power. By first time flying, slowly push up the left-hand shift rod of the remote control, inorder to prevent UAV from flying up rapidly and causing damages.
3. After the flight, the remote control should be powered off first before approaching the UAV to power off the UAV.
4. Never leave the battery in a hot, heated place (such as in a fire or near a heating device
5. Pay attention to the UAV and the user or other people when flying to maintain a distance of 2 to 3 meters, to avoid the UAV flight landing UAV hit the head, face or body of other people and so on.
6. Children should be guided by an adult when they operate the UAV. Please make sure that the U AV is within the sight of the operator (or instructor), in order to control easily.
7. Non-rechargeable batteries cannot be recharged. Please pay attention to the polarity when the batteries are installed or replaced. It is forbidden to mix up with the old and the new batteries or di fferent types of batteries.
8. Turn off the power of the remote control when the UAV is not in use. Moreover, please remove the batteries from the remote control.
9. The power terminal must not be shorted.

Matters needing attention

1. Remote control distance is affected when the power of the remote control or UAV is low.
2. Insufficient altitude or difficulty in takeoff if the UAV is undercharged.
3. If the UAV is damaged or deformed, please repair it in time. Otherwise it (e.g. broken spiral fan) may result in severe injuries.
4. Remove the batteries from the remote control if it is not used for a long period of time. In order to avoid the leakage of liquid from the battery, the product will be damaged.
5. Never let the UAV from high altitude drop off or happen a serious collision, as this could damage the UAV or shorten the life of the UAV.
6. This UAV model contains all kinds of aluminum components. Be careful not to get cut by the aluminum components when children are playing with the UAV.

Solutions to common problems

Number

| Reasons for the problem| Teason| Solutions
---|---|---|---
1|

Remote Control Failure

| Whether the frequency alignment with the UAV is successful and whether the remote control battery is charged.The wind is too strong.| Please follow the instructions for frequency conversion to replace the battery.Do not fly in a windy environment
2
3| UAV underpowered| Insufficient battery power| Please use the original factory BSB charger to charge the UAV.
4| UAVs out of control| Is the wind too strong for

the effective remote control distance?

| Do not fly in a windy environment. Make sure

the flight clearance is at the optimum distance of 50 meters.

5| UAVs don’t fly| Whether the fans are severely damaged or deformed| Please follow the instructions for the replacement of the fans and please use the blade splitter to replace the fans
6| UAV Flight Instability| Fan deformation or severe motor seat deformation| Please follow the instructions in the instruction manual for fan replacement, and please use the propeller disassembler to replace the fan correctly.

Warning: aircraft in flight Do not touch the aircraft.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>