Silex Technology SXPCEAN2 PCI Express Half Mini Card WLAN Module User Manual
- June 6, 2024
- silex technology
Table of Contents
User Manual
Since this module is not sold to general end users directly, there is no user manual of module.
For the details about this module, please refer to the specification sheet of module.
This module should be installed in the host device according to the interface specification (installation procedure).
The following information must be indicated on the host device of this module;
[for FCC]
Contains Transmitter Module FCC ID: N6C-SXPCEAN2
or
Contains FCC ID: N6C-SXPCEAN2
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
*If it is difficult to describe this statement on the host device due to the size, please describe in the user’s manual and also either describe on the device packaging or on a removable label attached to the device.
[for ISED(IC)]
Contains IC: 4908A-SXPCEAN2
The following statements must be described on the user manual of the host device of this module;
[for FCC]
FCC CAUTION
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Co-Location Rule
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter. However, Co-Location is allowed for where two
SX-PCEAN2 modules perform Co-Location.
List of applicable FCC rules
This device complies with below part 15 of the FCC Rules.
Part 15 Subpart C
Part 15 Subpart E
Information on test modes and additional testing requirements
silex technology, Inc. uses various test mode programs for test set up
which operate separate from production firmware. Host integrators should
contact silex technology, Inc. for assistance with test modes needed for
module/host compliance test requirements.
The modular transmitter is only FCC authorized for the specific rule parts
(i.e., FCC transmitter rules) listed on the grant, and the host product
manufacturer is responsible for compliance to any other FCC rules that apply
to the host not covered by the modular transmitter grant of certification.
The final host product still requires Part 15 Subpart B compliance testing
with the modular transmitter installed.
Additional testing, Part 15 Subpart B disclaimer
The modular transmitter is only FCC authorized for the specific rule parts
(i.e., FCC transmitter rules) listed on the grant, and the host product
manufacturer is responsible for compliance to any other FCC rules that apply
to the host not covered by the modular transmitter grant of certification.
The final host product still requires Part 15 Subpart B compliance testing
with the modular transmitter installed.
Summarize the specific operational use conditions
This module designed for mounting inside of the end product by us
professionally.
Therefore, it complies with the antenna and transmission system
requirements of §15.203.
RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines. This equipment should be installed and operated keeping the
radiator at least 20cm or more away from person’s body.
[for ISED]
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
1.This device may not cause interference.
2.This device must accept any interference, including interference that may
cause undesired operation of the device.
for indoor use only
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body ( ).
The following notice is not for end users but for the manufacturer of the host
device.
Therefore it isn’t described on the user manual of the host device.
This radio transmitter (4908A-SXPCEAN2) has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Antenna type
| 2.4GHz Gain| 5GHz Gain| Impedance
---|---|---|---
PCB
| +1.8dBi| +3.9dBi|
50hms
Rod| +2.0dBi| +2.1dBi|
50hms
Documents / Resources
|
Silex Technology SXPCEAN2 PCI Express Half Mini Card WLAN
Module
[pdf] User Manual
SXPCEAN2, N6C-SXPCEAN2, N6CSXPCEAN2, SXPCEAN2, PCI Express Half Mini Card WLAN
Module
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>