silex technology WDCU3310 Wireless E84 Digital Communication Unit User Manual
- June 5, 2024
- silex technology
Table of Contents
silex technology WDCU3310 Wireless E84 Digital Communication Unit
WDCU-3310 is a device that E84 interlock communication by wireless communication during FOUP transfer between the OH Overhead Hoist Transfer and semiconductor manufacturing equipment. The WDCU-3310 is equipped on the OHT.
Parts and Functions
Parts and Functions|
---|---
POWER LED| Green light on| Power On
Green light flashing| Program changing
Orange light on| Initializing process
Red light on| Hardware error
STATUS LED| Green light on| Power On
Green light flashing
| Setting various parameters of wireless E84 communication unit from wireless converter or OHT controller
Orange light flashing
| During PIIO data communication between the wireless converter or OHT control unit and the wireless E84 communication unit
Red light on
| Communication error occurred between wireless converter or OHT control unit
and wireless E84 communication unit
W-E84 LED| Green light on| Power On(2.4GHz)
Green light flashing| Communicating in the 2.4 GHz band
Orange light on| Power On(5.8GHz)
Orange light flashing| Communicating in the 5.8 GHz band
Red light on| An error occurred in communication with the wireless E84 device
3pin connector | Debug port |
---|---|
5pin connector | CPU internal ROM writing only used in the factory |
10pin connector | Connect to Wireless LAN converter (FBR-3250) or OHT |
Antenna connector | Connect the antenna |
Push Switch | Used to initialization settings |
Setup
Use a dedicated cable to connect the 10-pin connector to FBR-3250 or OHT. Power supplied from OHT and the WDCU-3310 is controlled by the OHT controller.
Basic configration|
---|---
Wireless Frequency Band| ISM(2.4GHz,5.8GHz)
Wireless Channel| Ch3~Ch80(2.4GHz) Ch2~Ch100(5.8GHz)
Wireless Channel Width| 1MHz
Channel Power setting| 20dBm~0dBm(2.4GHz)
20dBm~+2dBm(5.8GHz)
Channel Period| 10,20,30,40,50ms
Receive timeout| 100~60000ms
Commnication timeout| 100~5000ms
Pairing threshold level| 80~-24dB No threshold
SPECIFICATION
Specification|
---|---
Operating environment| Temperature 0~+40℃
Humidity 20~80%RH(Non condensing)
Strorage environment| Temperature 10~+50℃
Humidity 20~90%RH Non condensing
Power supply| DC24V
Wireless I/F| short-range wireless(2.4GHz/5.8GHz)
Push Switch| initializaition swtich ×1
LED
| POWER LED Green/Red/Orange
STATUS LED Green/Red/Orange
W-E84 LED Green/Red/Orange
- Supplier’s Declaration of Conformity
- 47 CFR 2.1077 Compliance Information Unique Identifier: WDCU-3310
- Responsible Party – U.S. Contact Information
- Responsible Party Name : silex technology America, Inc.
- Responsible Party Address:East Sandpointe, #245 Santa Ana, CA 92707
- Phone: 657-218-5199
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions
- This device may not cause harmful interference, and this device must accept any interference received, including interference undesired.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Compliance with FCC requirement 15.407
Data transmission is always initiated by software, which is the passed down
through the MAC, through the digital and analog baseband, and finally to the
RF chip. Several special packets are initiated by the MAC. These are the only
ways the digital baseband portion will turn on the RF transmitter, which it
then turns off at the end of the and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction packet.
Therefore, the transmitter will be on only while one of the aforementioned
packets is being transmitted. In other words, this device automatically
discontinue transmission in case of either absence of information to transmit
or operational failure.Frequency Tolerance: ±60 ppm. This transmitter must not
be co-located or operated in conjunction with any other antenna or
transmitter. This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment and meets the FCC radio frequency (RF)
Exposure Guidelines as this equipment has very low levels of RF energy.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>