ESX QUANTUM QL800.1 Class D Mono Amplifier Owner’s Manual

June 5, 2024
ESX QUANTUM

QL800.1 Class D Mono Amplifier
Owner’s Manual

SPECIFICATIONS

MODEL QL800.1

CHANNELS
CIRCUIT| 1
CLASS D
Digital
OUTPUT POWER RMS @ 14.4 V
Watts @ 4 Ohms
Watts @ 2 Ohms
Watts @ 1 Ohm| 1 x 325
1 x 550
1 x 800
OUTPUT POWER MAX. @ 14.4 V
Watts @ 4 Ohms
Watts @ 2 Ohms
Watts @ 1 Ohm| 1 x 650
1 x 1100
1 x 1600
Frequency Range –3dB
Damping Factor
Signal-to-Noise Ratio
THD&N
Input Sensitivity| 10 – 150 Hz

220 dB
81 dB
< 0,01%
5 – 0,2 V
Various Subsonic Filter
Various Lowpass Filter
Various Bass Boost
Various Phase Shift| 10 – 40 Hz
40 – 150 Hz
0 – 18 dB @ 40 Hz
0 – 180°
Start-stop capability
High Level Inputs
Auto Turn On
Bass Remote
Fullrange Outputs (RCA)| 8,5 V
via DC or Signal
yes
yes
stereo
Fuse Ratings Dimensions
Width x Height x Length| 70 A (external)
226 x 43 x 120 mm

Technical specifications are subject to change! Errors are reserved!

SAFETY INSTRUCTIONS

PLEASE NOTE THE FOLLOWING ADVICE BEFORE THE FIRST OPERATION!
THE PURCHASED DEVICE IS ONLY SUITABLE FOR AN OPERATION WITH A 12V ONBOARD ELECTRICAL SYSTEM OF A VEHICLE
. Otherwise, fire hazards, risk of injury, and electric shock consist.
PLEASE DO NOT MAKE ANY OPERATION OF THE SOUND SYSTEM, WHICH DISTRACT YOU FROM A SAFE DRIVING. Do not make any procedures, which demand longer attention. Perform these operations not until you have stopped the vehicle in a safe place. Otherwise, the risk of accident consists.
ADJUST THE SOUND VOLUME TO AN APPROPRIATE LEVEL, THAT YOU ARE STILL ABLE TO HEAR EXTERIOR NOISES WHILE DRIVING. High performance sound systems in vehicles may generate the acoustic pressure of a live concert. The permanent listening to extreme loud music may cause the loss of your hearing abilities. The hearing of extreme loud music while driving may derogate your cognition of warning signals in the traffic. In the interests of the common safeness, we suggest to drive with a lower sound volume. Otherwise the risk of accident consists.
DO NOT COVER COOLING VENTS AND HEAT SINKS. Otherwise this may cause heat accumulation in the device and fire hazard consists.
DO NOT OPEN THE DEVICE. Otherwise fire hazard, risk of injury and electric shock consists. Also this may cause a loss of the warranty.
REPLACE FUSES ONLY WITH FUSE WITH THE SAME RATING. Otherwise fire hazard and risk of electric shock consists.
THE INSTALLATION OF A POWER CAPACITOR WITH SUFFICIENT CAPACITY IS RECOMMENDED. High-performance amplifiers cause high potential voltage drops and need a high power consumption at a high volume level. To relieve the vehicle’s on-board system, it is recommended to install a power capacitor between the battery and the device which works as a buffer. Consult your car audio retailer for the appropriate capacity.
INTERCONNECTION AND INSTALLATION SHOULD BE ACCOMPLISHED BY SKILLED STAFF ONLY. The interconnection and installation of this device demand technical aptitude and experience. For your own safety, commit the interconnection and installation to your car audio retailer, where you have purchased the device.
DISCONNECT THE GROUND CONNECTION FROM THE VEHICLE’S BATTERY BEFORE INSTALLATION. Before you start with the installation of the sound system, disconnect by any means the ground supply wire from the battery, to avoid any risk of electric shock and short circuits.
CHOOSE AN APPROPRIATE LOCATION FOR THE INSTALLATION OF THE DEVICE. Look for an appropriate location for the device, which ensures sufficient air circulation. The best places are spare wheel cavities and open spaces in the trunk area. Less suitable are storage spaces behind the side coverings or under the car seats.
DO NOT INSTALL THE DEVICE AT LOCATIONS, WHERE IT WILL BE EXPOSED TO HIGH HUMIDITY AND DUST. Install the device at a location, where it will be protected from high humidity and dust. If humidity and dust attain inside the device, malfunctions may be caused.
MOUNT THE DEVICE AND OTHER COMPONENTS OF THE SOUND SYSTEM SUFFICIENTLY. Otherwise, the device and components may get loose and act as dangerous objects, which could cause serious harm and damage in the passenger room.
ENSURE NOT TO DAMAGE COMPONENTS, WIRES, AND CABLES OF THE VEHICLE WHEN YOU DRILL THE MOUNTING HOLES. If you drill the mounting holes for the installation into the vehicle’s chassis, ensure by any means, not to damage, block, or tangent the fuel pipe, the gas tank, other wires or electrical cables.
ENSURE CORRECT CONNECTION OF ALL TERMINALS. Faulty connections may cause fire hazards and lead to damage of the device.
DO NOT INSTALL AUDIO CABLES AND POWER SUPPLY WIRES TOGETHER. Ensure while installation not to lead the audio cables between the head unit and the amplifier together with the power supply wires on the same side of the vehicle. The best is an areal separated installation in the left and right cable channel of the vehicle. Therewith an overlap of interferences on the audio signal will be avoided. This stands also for the equipped bass remote wire, which should be installed not together with the power supply wires, but rather with the audio signal cables.
DO NOT USE THE DEVICE ANY LONGER, IF A MALFUNCTION, WHICH REMAINS UNREMEDIED. Refer in this case to the chapter TROUBLESHOOTING. Otherwise risk of injury and the damage of the device consists. Commit the device to an authorized retailer.
ENSURE THAT CABLES MAY NOT BE CAUGHT UP IN CLOSE-BY OBJECTS. Install all the wires and cables as described on the following pages, therewith these may not hinder the driver. Cables and wires which are installed close by the steering wheel, gear lever, or the brake pedal, may be caught up and cause highly dangerous situations.
DO NOT SPLICE ELECTRICAL WIRES. The electrical wires should not be bared, to provide power supply to other devices. Otherwise, the load capacity of the wire may get overloaded. Use therefore an appropriate distribution block. Otherwise fire hazards and risk of electric shock consist.
DO NOT USE BOLTS AND SCREW NUTS OF THE BRAKE SYSTEM AS A GROUND POINT. Never use for the installation or the ground point bolts and screw-nuts of the brake system, steering system or other security-relevant components. Otherwise, fire hazards consist of the driving safety will be derogated.
ENSURE NOT TO BEND OR SQUEEZE CABLES AND WIRES WITH SHARP OBJECTS. Do not install cables and wires not close-by movable objects like the seat rail that may be bent or harmed by sharp and barbed edges. If you lead a wire or cable through the hole in a metal sheet, protect the insulation with a rubber grommet.
KEEP AWAY SMALL PARTS AND JACKS FROM CHILDREN. If objects like these will be swallowed, the risk of serious injuries consists. Consult promptly a medical doctor, if a child swallowed a small object.

INSTALLATION INSTRUCTIONS

NOTE
Before you start with the installation of the sound system, disconnect necessarily the GROUND connection wire from the battery to avoid any risk of electric shocks and short circuits.

MECHANICAL INSTALLATION

Avoid any damage to the components of the vehicle like airbags, cables, board computers, seat belts, gas tanks,s or the like. Ensure that the chosen location provides sufficient air circulation for the amplifier. Do not mount the device into small or sealed spaces without air circulation near heat dispersing parts or electrical parts of the vehicle. Do not mount the amplifier on top of a subwoofer box or any other vibrating parts, whereby parts could loosen inside. The wires and cables of the power supply and the audio signal must be as short as possible to avoid any losses and interferences.
First, you need to find a suitable installation location for the amplifier. Ensure that enough space for the installation of the cables remains and that they will not be bent
and have sufficient pull relief.
Keep the amplifier at the chosen mounting location in the vehicle. Then mark the four drill holes with an appropriate pen or marking tool through the designated mounting holes at the amplifier.
Lay the amplifier aside and then drill the holes for the mounting screws at the marked locations.
Please ensure not to damage any components of the vehicle while you drilling the holes. Alternatively (depending on the material of the surface) you can also use self-tapping screws.
Then uphold the amplifier to the chosen position and fix the screws through the mounting holes into the drilled screw holes.
Ensure that the mounted amplifier is tightly fixed and can not come loose while driving.
INSTALLATION INSTRUCTIONS

ELECTRICAL INTERCONNECTION

BEFORE CONNECTING

For the professional installation of a sound system, car audio retail stores offer appropriate wire kits. Ensure a sufficient profile section (at least 25 mm2), a suitable fuse rating, and the conductivity of the cables when you purchase your wiring kit. Clean and remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection. Make sure that all screws are fixed tight after the installation because loose connections cause malfunctions, insufficient power supply or interferences. Do not set in the fuse until the installation is accomplished.

  1. GND
    Connect the GND terminal with a suitable contact ground point on the vehicle’s chassis. The ground wire must be as short as possible and must be connected to a blank metallic point at the vehicle’s chassis. Ensure that this ground point has a stable and safe electrical connection to the negative “­” pole of the battery. Check this ground wire from the battery to the ground point if possible and enforce it if required. Use a ground wire with a sufficient cross-section (at least 25 mm2) and the same size as the plus (+12V) power supply wire.

  2. REM IN/OUT
    Connect a turn-on signal (e.g. automatic antenna) or the turn-on remote signal of your head unit (REM) with the REM IN/OUT terminal of the amplifier. Use therefore a suitable cable with a sufficient cross-section (0,5 mm2). Hereby the amplifier turns on or off with your head unit.
    If you use the AUTO TURN-ON function, the REM IN/OUT terminal does not need to be connected. However, the REM IN/OUT terminal can then be connected to the REM terminal of another amplifier to provide a control signal to it (REM OUT function).

  3. +12V
    Connect the +12V terminal with the +12V pole of the vehicle’s battery. Use a suitable cable with a sufficient cross section (at least 25 mm2).

  4. FUSE
    The amplifier inherently has no internal device fuse. Use the supplied fuse (70 A) with the fuse holder and install it in the power cable between the 12 Volt positive pole of the vehicle battery and the +12V terminal of the amplifier. The distance between the fuse and the amplifier should not exceed 30 cm.

  5. ADDITIONAL CABLE FUSE (OPTIONAL)
    Install an extra fuse (at least 70 A, not included) for the +12V power cable near the battery. The distance between the fuse and the battery should not exceed 30 cm.
    Replace defective fuses only with a new one of the same type and with the same fuse rating.

FUNCTIONAL INSTRUCTIONS


OPERATING ELEMENTS

  1. Connect the INPUT RCA jacks with the head unit by using appropriate audio signal cables.

  2. The OUTPUT RCA jacks provide a linear full-range audio signal for driving additional amplifiers.

  3. If your head unit does not have RCA preamp outputs, you can use the amplifier’s HIGH-LEVEL INPUT as the signal input. To do this, simply connect the loudspeaker cables of the head unit to the enclosed cable plug as follows:
    White:………..Left front +
    White-Black:………………..Left front
    Gray:…………..­ Right front +
    Gray-Black:……………… Right front

  4. The LEVEL INPUT controller determines the input sensitivity (adaptation to the output signal of the head unit). The controller range is between 5 volts (MIN) and 0.2 volts (MAX).

  5. The SUB SONIC controller limits the ultra-low and not audible frequencies of the audio signal downwards to avoid mechanical and electrical overloading on the subwoofer. The cut-off frequency is adjustable from 10 to 40 Hz and depends on the size of the subwoofer.

  6. If the POWER/PROTECT is green, the amplifier is ready for operation. If the POWER/PROTECT is red, there is a malfunction. Refer in this case to the section TROUBLESHOOTING.

  7. The LOW PASS controller determines the frequency cut-off upwards. The crossover frequency is continuously variable from 40 Hz to 150 Hz (5 kHz).

  8. If your head unit does not have a turn-on signal (REM), you can use the automatic turn-on function of the amplifier. This works in two ways, which can be set at the AUTO TURN-ON switch:
    DC: This method only works if you use the amplifier’s HIGH-LEVEL INPUT. The amplifier then detects a voltage rise to 6 volts when the head unit is turned on by a so-called “DC offset” and then turns on the amplifier.
    VOX: Select this method when using the INPUT RCA jacks. The amplifier then detects a voltage increase in the incoming audio signal when switching on the head unit via the attached RCA cable and then switches on the amplifier.
    Note: As soon as the head unit is switched off again, the amplifier switches itself off. The terminal for the amplifier turn-on (page 17# 2, REM IN/OUT) can now be used to supply additional amplifiers with a turnon signal. Simply connect the REM terminals of the two amplifiers and make sure that the other amplifier is in “normal” turn-on mode, which means that the AUTO TURN ON function is disabled.

  9. The BASS BOOST controller adjusts the bass boost continuously from 0 dB to +18 dB at 40 Hz.
    NOTE: Always use this controller with care. A permanently too high bass boost could damage your speakers!

  10. The REMOTE port is for connecting the cable of the included bass level remote controller. With this, the bass level can be e.g. be adjusted from the driver’s seat. Only use the supplied bass remote controller and the associated cable.

  11. The PHASE SHIFT controller allows adjusting the phase between 0° and 180°. Hence, you are able to adjust the subwoofer perfectly to the vehicle’s acoustics.

NOTE
Installation of RCA/Audio signal cables and power supply cables.
Ensure while installation not to lead the audio cables between the head unit and the amplifier together with the power supply wires on the same side of the vehicle. The best is a real separated installation on the left and right cable channels of the vehicle to avoid interferences on the audio signal. This stands also for the enclosed bass-remote wire, which should not be installed together with the power supply wires.

INTERCONNECTION EXAMPLE

1-channel-mode: 1 x Mono Subwoofer

INTERCONNECTION

  • Connect the RCA outputs of the head unit with the RCA jacks INPUT (L /R) of the amplifier with appropriate high-value RCA cables. If a separate SUB OUT from your head unit is available, use this as line output.
  • Connect the subwoofer with the SPEAKER OUTPUTS + and -.
  • Always ensure that the total impedance load is not lower than 1 ohm. Too low impedance causes a high temperature and will shut down the amplifier operation.
  • Always ensure the correct polarity of the speakers. The interchange of plus and minus causes total loss of bass playback and could damage the speakers.

FILTER SETTINGS & BASS BOOST CONTROLLER 

  • The cut-off frequency is adjustable with the LOW PASS controller and should be set between 60 to 100 Hz, depending on the size of the subwoofer. The SUB SONIC controller eliminates the ultra-low, not audible frequencies to generate a bandpass signal. The subsonic frequency should be set between 15 to 40 Hz, depending on the size of the subwoofer.
    Note: If this value is higher than the LOW PASS setting, no sound is audible.

  • The BASS BOOST controller allows a bass enhancement up to +18 dB.

LEVEL CONTROLLER

  • Turn the LEVEL INPUT controller of the amplifier to the MIN position.
  • Turn the volume controller of the head unit to 80 – 90% of its full setting.
  • Turn the LEVEL INPUT controller clockwise until you hear some distortion.
  • Then turn back the LEVEL INPUT controller slightly until you hear a cleaner sound.

BASS REMOTE

  • The enclosed BASS REMOTE CONTROLLER adjusts the bass level e.g. from the driver’s seat. Please use only the enclosed bass remote controller and cable.

NOTE
Do not connect loudspeaker cables with the vehicle’s chassis. Always ensure the correct polarity of all connections.

INTERCONNECTION EXAMPLE
1-channel-mode: 2 x Mono Subwoofer
INTERCONNECTION

  • Connect the RCA outputs of the head unit with the RCA jacks INPUT (L /R) of the amplifier with appropriate high-value RCA cables. If a separate SUB OUT from your head unit is available, use this as line output.

  • Connect each subwoofer with the SPEAKER OUTPUTS + and -.

  • Always ensure that the total impedance load is not lower than 2 ohms.
    Too low impedance causes a high temperature and will shut down the amplifier operation.

  • Always ensure the correct polarity of the speakers. The interchange of plus and minus causes total loss of bass playback and could damage the speakers.

FILTER SETTINGS & BASS BOOST CONTROLLER

  • The cut-off frequency is adjustable with the LOW PASS controller and should be set between 60 to 100 Hz, depending on the size of the subwoofer. The SUB SONIC controller eliminates the ultra-low, not audible frequencies to generate a bandpass signal. The subsonic frequency should be set between 15 to 40 Hz, depending on the size of the subwoofer. Note: If this value is higher than the LOW PASS setting, no sound is audible.
  • The BASS BOOST controller allows a bass enhancement up to +18 dB.

LEVEL CONTROLLER

  • Turn the LEVEL INPUT controller of the amplifier to the MIN position.
  • Turn the volume controller of the head unit to 80 – 90% of its full setting.
  • Turn the LEVEL INPUT controller clockwise until you hear some distortion.
  • Then turn back the LEVEL INPUT controller slightly until you hear a cleaner sound.

BASS REMOTE

  • The enclosed BASS REMOTE CONTROLLER adjusts the bass level e.g. from the driver’s seat.
    Please use only the enclosed bass remote controller and cable.

NOTE
Do not connect loudspeaker cables with the vehicle’s chassis. Always ensure the correct polarity of all connections.

TROUBLESHOOTING

ELECTRICAL INTERFERENCES
The reason for interferences is mostly the routed cables and wires. Especially the power and audio cables (RCA) of your sound system are vulnerable. Often these interferences are caused by electric generators or other electrical units (fuel pump, AC, etc.) of the car. Most of these problems can be prevented by correct and careful wiring.
Here are some courtesy notes :

  1. Use only double or triple shielded audio RCA cables for the connection between the amplifier and head unit. A useful alternative is represented by anti-noise devices or additional ancillary equipment like Balanced Line transmitters, which you can purchase at your car audio retailer. If possible do not use anti-noise filters, which are splicing the ground of the RCA audio cables.
  2. Do not lead the audio cables between the head unit and the amplifier together with the power supply wires on the same side of the vehicle. The best is a real separated installation on the left and right cable channels of the vehicle. Then the overlapping of interferences on the audio signal will be avoided. This stands also for the enclosed bass-remote wire, which should not be installed together with the power supply wires.
  3. Avoid ground loops by connecting all ground connections in a starlike arrangement. The suitable ground center point is ascertainable by measuring the voltage directly on the vehicle’s battery by a multi-meter. You should measure the voltage with turned-on ignition (acc.) and with other turned-on power consumers (e.g. headlights, rear window defroster, etc,). Compare the measured value with the voltage of the ground point you have chosen for the installation and the positive pole (+12V) of the amplifier. If the voltage has just a little difference, you have found a suitable ground point. Otherwise, you need to choose another ground point.
  4. Use if possible only cables with added or soldered cable sockets or the like. Gold-plated or high-value nickel-plated cable sockets are corrosion-free and own a very low contact resistance.

PROTECTION CIRCUIT

This amplifier owns a 3-way protection circuit. On overloading, overheating, shorted loudspeakers, too low impedance, or insufficient power supply, the protection circuit turns off the amplifier to prevent serious damage. If one of these malfunctions is detected, the POWER/ PROTECT LED lights up red.
In this case, check all connections to detect short-circuits, faulty connections, or overheating. Refer to the notes on the next page.
If the reason for the dysfunction is eliminated, the amplifier is ready for operation again.
If the red POWER/PROTECT LED does not stop to light up in red, the amplifier is damaged. In this case, return the amplifier to your car audio retailer with a detailed malfunction description and a copy of the proof of purchase.
WARNING: Never open the amplifier and try to repair it by yourself. This causes a loss of warranty. The repairing service should be made only by skilled technicians.
INSTALLATION AND OPERATION IN NEWER VEHICLES!
In many vehicles (since approx. 2002) computer-controlled diagnosis- and controlling systems are applied – like CAN-BUS or MOST-BUS interfaces. With the installation of a car audio amplifier, a new appliance will be added to the 12V onboard electrical system, which may cause under several circumstances error messages or may interrupt the factory-made diagnosis system, as a result of high-stress peaks and higher power consumption. Thus, depending on the model and manufacturer, the driving safety or important security systems like airbags, ESC or others could be interrupted.
If you plan to operate the amplifier in a vehicle like described above, please follow these instructions:

  • Let the installation be made only by a skilled specialist or a service station, which is specialized in the maintenance of your vehicle.
  • After the installation, we suggest making a computer diagnosis of the onboard system, to detect possible malfunctions or errors.
  • If the onboard system is interfered with by the installation of the amplifier, an additionally installed power capacitor can stabilize the electrical onboard system to ensure a proper and stable operation.
  • The best solution is the integration of an own additional 12 V electrical system for the sound system, which can be operated independently with its own battery supply.

CONSULT YOUR CAR SPECIALIZED SERVICE STATION!

Malfunction: no function

Reason:
1. The power supply connection of the device is not correct
2. The cables have no mechanical or electrical contact
3. The remote turn-on connection from the head unit to the amplifier is not correct
4. Defective Fuses. In case of replacing the fuses, ensure the correct fuse rating| Remedy:
Recheck
Recheck
Recheck
Replace Fuses
---|---

Malfunction: no signal on loudspeakers, but the POWER/PROTECT LED lights up green

Reason:
1. The connections of the speakers or the RCA audio cables are not correct
2. The speaker cables or the RCA audio cables are defective
3. The loudspeakers are defective
4. SUB SONIC controller is adjusted too high
5. No signal from the head unit| Remedy:
Recheck
Replace cables
Replace speakers
Turn down the controller
Check head unit settings
---|---

Malfunction: one or more channels/controllers are without function / faulty stereo stage

Reason:
1. The balance or fader controller of the head unit is not in the center- position
2. The connections of the speakers are not correct
3. The loudspeakers are defective
4. SUB SONIC controller is adjusted to high| Remedy :
Turn to center-position
Recheck
Replace speakers
Turn down the controller
---|---

Malfunction: distortions on the loudspeakers

Reason: 1.
The loudspeakers are overloaded| Remedy:
Turn down the level
Turn down the level on the head unit
Switch off loudness on the head unit
Reset bass EQ on the head unit
---|---

Malfunction: No bass or stereo sound

Reason:
1. Interchange of loudspeaker cable polarity
2. The RCA audio cables are loose or defective| Remedy:
Reconnect
Reconnect or replace the cables
---|---

Malfunction: amplifier runs into protection mode (POWER/PROTECT LED lights up red)

Reason:
1. Short circuit on the loudspeakers or cables
2. Overheated by too low speaker impedance
3. Insufficient air circulation by a inappropriate mounting position of the amplifier
4. Overloaded by insufficient power supply (too small profile section on the power cables)| Remedy:
Reconnect
Choose a higher impedance
Use a new speaker setup
Change the mounting position
Ensure air circulation
Use a bigger profile section
---|---

Malfunction: hiss or white noise on the loudspeakers

Reason:
1. The level controllers are turned up to loud
2. The treble controller on the head unit is turned up
3. The speaker cables or the RCA audio cables are defective
4. The hissing is caused by the head unit| Remedy:
Turn down the level
Turn down the level on the head unit
Replacing the cables
Check the head unit
---|---

Audio Design GmbH
Am Breilingsweg 3
D-76709 Kronau/Germany
Tel. +49 7253 – 9465-0
Fax +49 7253 – 946510
www.esxaudio.de
www.audiodesign.de
© Audio Design GmbH, all rights reserved.
Technical changes, errors, and mistakes reserved.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals