Alcatel-Lucent OAW-AP1351 OmniAccess Stellar Access Point Installation Guide
- June 6, 2024
- Alcatel-Lucent
Table of Contents
Alcatel-Lucent OAW-AP1351 OmniAccess Stellar Access Point Installation
Guide
Summary of Installation Steps
- WLAN Planning. Usually, a comprehensive site survey is required before installation, such as installation location, brackets, cables, power source, etc.
- Unpack the AP box and check all contents
- Install the AP bracket on ceiling or wall
- Installing the AP
- Connecting required cables
- Power connection
- Verifying post-installation connectivity
- AP provisioning
Access points are radio transmission devices and are subject to governmental regulation. Network administrators who are responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, access point must use channel assignments appropriate to the location where the access point will be deployed.
Package Contents
| Item | Name | Qty | Unit |
|---|---|---|---|
| 1 | Access Point | 1 | Pcs |
| 2 | Quick Start Guide | 1 | Pcs |
| Installation Guide | 1 | Pcs | |
| Regulatory Compliance and Safety Information | 1 | Pcs | |
| User Guide Info Card | 1 | Pcs |
Optional Accessories (To be ordered separately)
| Item | Name | Description |
|---|---|---|
| 1 | OAW-AP-MNT-B | Indoor mounting kit, Type B1(9/16″) and B2(15/16″) for T |
shaped ceiling rail.
2| OAW-AP-MNT-C| Indoor mounting kit, Type C1(Open
Silhouette) and C2 (Flanged Interlude), for other shaped ceiling rail mounting.
3| OAW-AP-MNT-W| Indoor mounting kit, Type W wall and ceiling mounting with screws.
Figure1: Product Packing
Inform your ALE sales representative of incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed. Additional mounting kits for use with the OmniAccess Stellar access points are sold separately. Contact your ALE sales representative for details.
Hardware Overview
The following sections outline the hardware components of the OAWAP1351 Series access point.
Figure 2: OAW-AP1351 Front View
LED
The OAW-AP1351 Series access point is equipped with hidden LED display that
indicates different status with different color.
For the details of the LED status, please refer to the Quick Start Guide.
Figure 3: OAW-AP1351 Back View
OAW-AP1351 series External Interfaces
| Interface | Specifications |
|---|---|
| 1 Gigabit Eth0 | 1x 10/100/1000BASE-T autosensing (RJ-45) port, Power over |
Ethernet (PoE). In case of only one WAN link，Eth0 would be preferred.
1 Gigabit Eht1| 1x 10/100/1000BASE-T autosensing (RJ-45) port, Power over
Ethernet (PoE). In case of only one WAN link， either of Eth0 and Eth1 could
work as WAN, Eth0 would be more preferred. In case of two WAN links，Eth0 +
Eth1 would be preferred.
Console| RJ-45 connector, default is RS-232 Console for Service & Support
only. Support software configure to RS-485 mode.
USB| USB 3.0 host interface (Type C, output current 0.5A )
DC Power Socket| DC 48V power jack, support powering AP through a designated
AC-DC power adapter.
Reset| Factory reset. Press reset button for 5s, AP LEDs will quickly flash
for 3s, then AP will restart and restore factory configurations.
Security Lock Slot| The AP is equipped with a security lock slot for
additional security.
Table 2
Ethernet Port Pinout
| Connector | Pin | Signal Name | PoE |
|---|---|---|---|
| 1 | RJ45_DA+ | PoE- | |
| 2 | RJ45_DA– | PoE- | |
| 3 | RJ45_DB+ | PoE+ | |
| 4 | RJ45_DC+ | PoE+ | |
| 5 | RJ45_DC– | PoE+ | |
| 6 | RJ45_DB– | PoE+ | |
| 7 | RJ45_DD+ | PoE- | |
| 8 | RJ45_DD– | PoE- |
Table 3
Console Port Pinout
| Connector | Pin | Signal Name | Function |
|---|---|---|---|
| 3 | TXD | Transmit | |
| 4 | GND | Ground | |
| 5 | GND | Ground | |
| 6 | RXD | Receive |
Pins not listed must be not connected.
Power
The OAW-AP1351 series access point supports direct DC power adapter (48V DC
nominal, sold separately) and Power over Ethernet (PoE).
The DC power connector port is located on the back of the device, as shown in
Figure 3.
The PoE allows the Ethernet port to draw power from an IEEE 802.3at compliant
source with full functionality.
OmniAccess Stellar AP supports the power adapter provided by ALE ONLY.
Before You Begin
Refer to the sections below before beginning the installation process.
Pre-installation Checklist
Before installing your OAW-AP1351 Stellar access point, be sure that you have the following items:
- 8-conductor, CAT5 or better UTP cable of required length.
- One of the following power sources:
- IEEE 802.3at compliant Power over Ethernet (PoE) source (PoE switch or PoE injector).
- AC-DC adapter (sold separately)，output voltage DC 48V, output current ≥1.1A
- A terminal or a notebook
Identifying Specific Installation Locations
You can mount the OmniAccess Stellar AP on a ceiling rail or on a wall. You should first determine the location of the installation. The installation position is located at the center of the required coverage area and should be free from obstructions or obvious sources of interference.
- Minimize the number of obstructions (such as walls) between the AP and user terminals.
- Electronic equipment or devices (such as microwave ovens) which may produce radio frequency noise should be away from the installation position of the AP.
It is strictly prohibited to install around stagnant water, water seepage, leakage or condensation. Avoid cable condensation or water seepage along the cables connecting to the AP.
AP Installation
Refer to mounting kits installation Guide.
Verifying Post-Installation Connectivity
The LED on the AP can be used to verify that the AP is receiving power and initializing successfully.
Introduction
This document contains domestic and international regulatory compliance information for the access point OAW-AP1351. To ensure that this device complies with the regulatory standards for your region, please refer to the content below.
FCC Part 15:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generate, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This product may not be collocated or operated in conjunction with any other antenna or transmitter This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.
For EU
ALE USA Inc., hereby declares that these models are compliant with the
essential requirements and other provisions of Directive 2014/53/EU. For the
complete CE DoC, please access the website below to get more information:
https://businessportal2.alcatel-lucent.com/
Waste Electrical and Electronic Equipment (WEEE) Statement
ALE products are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland when they are at end of life, and therefore are marked with the symbol shown. The treatment applied to these products in these countries shall be compliant with the applicable national laws which are under the implementing of Directive 2012/19/EU on Waste of Electrical and Electronic Equipment (WEEE).
European Union RoHS
ALE products are compliant with the EU Restriction of Hazardous Substances Directive 2011/65/EU (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. The restricted materials under the Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, equivalent Chromium, and Bromine.
Global RF health information:
RF Radiation Exposure Statement: This equipment complies with FCC and CE RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 20 cm between the equipment and a human’s body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The device is restricted to indoor use only when operating in the 5150 to 5350
MHz frequency range.
IC Radiation Exposure Statement for Canada
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent is otropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
User manuals for transmitters equipped with detachable antennas shall also contain the following notice in a conspicuous location:
This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
IMPORTANT NOTE
Radiation Exposure Statement:
This equipment complies with “Industry Canada RSS-102 for radiation exposure
limits set forth for an uncontrolled environment”.
This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
Industry Canada – Emissions compliance statement
https://www.al-enterprise.com
The Alcatel-Lucent name and logo are trademarks of Nokia used under license by
ALE. To view other trademarks used by affiliated companies of ALE holding,
visit: https://www.alenterprise.com/en/legal/trademarks-copyright. All other
trademarks are the property of their respective owners. The information
presented is subject to ALE without notice. Neither ALE
Holding nor any of its affiliates assumes any responsibility for inaccuracies
contained herein. (2021)
The Alcatel-Lucent name and logo are trademarks of Nokia used under license by ALE. To view other trademarks used by affiliated companies of ALE Holding, visit: www.al-enterprise.com/en/legal/trademarks-copyright. All other trademarks are the property of their respective owners. The information presented is subject to change without notice. Neither ALE Holding nor any of its affiliates assumes any responsibility for inaccuracies contained herein. (2020)
This Class B digital apparatus complies with Canadian ICES-003.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>