Alcatel-Lucent Enterprise AP1411 OmniAccess Stellar Instruction Manual

**Alcatel-Lucent Enterprise AP1411 OmniAccess Stellar Instruction Manual

**

Summary of Installation Steps

• WLAN Planning. Usually, a comprehensive site survey is required before installation, such as installation location, brackets, cables, power source, etc.
• Unpack the AP box and check all contents
• Install the AP bracket on ceiling or wall
• Installing the AP
• Connecting required cables
• Power connection
• Verifying post-installation connectivity
• AP provisioning

Access points are radio transmission devices and are subject to governmental regulation. Network administrators who are responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, an access point must use channel assignments appropriate to the location where the access point will be deployed.

Package Contents

• Optional Accessories（To be ordered separately）

spare ceiling rail mounting.
2| AP-MNT-IN-CE| Mounting kit, Type CE1 (Open Silhouette) and CE2 (Flanged Interlude), for other shaped ceiling rail mounting.
3| OAW-AP-MNT-W| Indoor mounting kit, Type W wall mounting with screws.

Figure1: Product Packing

Inform your ALE sales representative of incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed. Additional mounting kits for use with the OmniAccess Stellar access points are sold separately. Contact your ALE sales representative for details.

Hardware Overview

The following sections outline the hardware components of the OAWAP1411 access point.

**Figure 2: OAW-AP1411 Front View

**

LED

The OAW-AP1411 access point is equipped with hidden LED display that indicates different status with different color.

For the details of the LED status, please refer to the Quick Start Guide.

Figure 3: OAW-AP1411 Back View

• OAW-AP1411 External Interfaces

Ethernet (PoE) 802.3at compliant.
1 Gigabit Eht1| 1000BASE-T/ 100BASE-TX (RJ-45) port.
Console| RJ-45 connector, RS-232 Console for Service & Support only.
USB| USB 3.0 host interface (Type A, output current 0.5A )
DC Power Socket| DC 48V power jack, support powering AP through a designated AC-DC power adapter.
Reset| Factory reset. Press reset button for 5s, AP LEDs will quickly flash for 3s, then AP will restart and restore factory configurations.
Security Lock Slo| The AP is equipped with a security lock slot for additional secur

Table 2 Ethernet Port Pinout

Table 3 Console Port Pino

Pins not listed must not be connected

Power

The OAW-AP1411 access point supports direct DC power adapter (48V DC nominal, sold separately) and Power over Ethernet (PoE).
The DC power connector port is located on the back of the device, as shown in Figure 3.
The PoE allows the Ethernet port to draw power from an IEEE
802.3at source with full functionality.
Maximum (worst case) power consumption:

• 25W (singe input IEEE 802.3at PoE): Unrestricted functionality

Omni Access Stellar AP supports the power adapter provided by ALE ONLY.

Before You Begin

Refer to the sections below before beginning the installation process.

Pre-installation Checklist

Before installing your OAW-AP1411 Stellar access point, be sure that you have the following items:

• 8-conductor, CAT5e or better UTP cable of required length.
  • CAT5e or better supports 5GE up to 100meters
• One of the following power sources:
  • IEEE 802.3at compliant Power over Ethernet (PoE) source (PoE switch or PoE injector), with full functions.
  • AC-DC adapter (sold separately), output voltage DC 48V, output current ≥0.55A
• A terminal or a notebook

Identifying Specific Installation Locations

You can mount the OmniAccess Stellar AP on a ceiling rail or on a wall. You should first determine the location of the installation. The installation position is located at the center of the required coverage area and should be free from obstructions or obvious sources of interference.

• Minimize the number of obstructions (such as walls) between the AP and user terminals.
• Electronic equipment or devices (such as microwave ovens) which may produce radio frequency noise should be away from the installation position of the AP.

It is strictly prohibited to install around stagnant water, water seepage, leakage or condensation. Avoid cable condensation or water seepage along the cables connecting to the

AP Installation

Refer to mounting kits installation Guide.

Verifying Post-Installation Connectivity

The LED on the AP can be used to verify that the AP is receiving power and initializing successfully.

Product Specifications

OAW-AP1411 Dimensions/Weight

Unboxed OAW-AP1411:

• Net Weight: 2.22lbs / 1.01kg
• Dimensions (HxWxD): 8.27 inches x 8.27 inches x 1.57 inches (21 cm x 21cm

Environmental

Operating :

• Temperature : 0°C to +45°C (+32°F to +113°F)
  • Humidity: 5% to 95% non-condensing
• Storage and transportation :
  • Temperature: -40°C to +70°C(-40°F to +158°F)

For additional specifications on this product, please refer to the Datasheet.

Contacting Alcatel-Lucent Enterprise

Website Support|
---|---
Main Site| https://www.al-enterprise.com/
Support Site.| https://myportal.al-enterprise.com
Support Email| ebg_global_supportcenter@al-enterprise.com Telephone Support
Telephone Support
North America| 1-800-995-2696
Latin America| 1-877-919-952
Europe| +800 00200100 (Toll Free) or +1(650)385
Asia P| +65 6240 8
Other Region| 1-818-878-4507

Introduction

This document contains domestic and international regulatory compliance information for the access point OAW-AP1431 and OAW-AP1411. To ensure that this device complies with the regulatory standards for your region, please refer to the content below.

FCC Part 15:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures.

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment

• FCC regulations restrict the operation of this device to indoor use only.
• The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet.
• Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems.

RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This product may not be collocated or operated in conjunction with any other antenna or transmitter.

This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.

For EU
ALE USA Inc., hereby declares that these models are compliant with the essential requirements and other provisions of Directive 2014/53/EU. For the complete CE DoC, please access the website below to get more information:
https://myportal.al-enterprise.com

Waste Electrical and Electronic Equipment (WEEE) Statement ALE products are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland when they are at end of life, and therefore are marked with the symbol shown. The treatment applied to these products in these countries shall be compliant with the applicable national laws which are under the implementing of Directive 2012/19/EU on Waste of Electrical and Electronic Equipment (WEEE).

European Union RoHS

ALE products are compliant with the EU Restriction of Hazardous Substances Directive 2011/65/EU (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. The restricted materials under the Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, equivalent Chromium, and Bromine.

For UK

This equipment complies with the essential requirements of following regulations: Radio Equipment Regulations 2017，

The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.

Declaration of Conformity may be obtained from: ALE

International 32 avenue Kléber – 92700 Colombes, France – ebgglobalsupportcenter@al-enterprise.com

Global RF health information:

RF Radiation Exposure Statement: This equipment complies with FCC and CE RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 20 cm between the equipment and a human’s body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The device is restricted to indoor use only when operating in the 5150 to 5350 MHz and 5945 to 6425 MHz frequency range.

[REMAINING SECTIONS INTENTIONALLY LEFT BLANK]

The Alcatel-Lucent name and logo are trademarks of Nokia used under license by ALE. To view other trademarks used by affiliated companies of ALE Holding, visit: www.al-enterprise.com/en/legal/trademarks-copyright. All other trademarks are the property of their respective owners. The information presented is subject to change without notice. Neither ALE Holding nor any of its affiliates assumes any responsibility for inaccuracies contained herein. (2022)

https://www.al-enterprise.com
The Alcatel-Lucent name and logo are trademarks of Nokia used under license by ALE. To view other trademarks used by affiliated companies of ALE holding, visit: https://www.alenterprise.com/en/legal/trademarks-copyright. All other trademarks are the property of their respective owners. The information presented is subject to ALE without notice. Neither ALE Holding nor any of its affiliates assumes any responsibility for inaccuracies contained herein. (2023)

References

• Trademarks Copyright | Alcatel-Lucent Enterprise
• myportal.al-enterprise.com
• myportal.al-enterprise.com/
• ALE Home | Alcatel-Lucent Enterprise
• ALE Home | Alcatel-Lucent Enterprise

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>