Alcatel-Lucent AP1301 Series OmniAccess Stellar Access Point Installation Guide

June 6, 2024
Alcatel-Lucent

AP1301 Series OmniAccess Stellar Access Point
Installation Guide

Summary of Installation Steps

  • WLAN Planning. Usually, a comprehensive site survey is required before installation, such as installation location, brackets, cables, power source, etc.
  • Unpack the AP box and check all contents
  • Install the AP bracket on the ceiling or wall
  • Installing the AP
  • Connecting required cables
  • Power connection
  • Verifying post-installation connectivity
  • AP provisioning

Access points are radio transmission devices and are subject to governmental regulation. Network administrators who are responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, the access point must use channel assignments appropriate to the location where the access point will be deployed.

Package Contents

Item Name Qty Unit
1 Access Point 1 Pcs
2 Quick Start Guide 1 Pcs
Installation Guide 1 Pcs
Regulatory Compliance and Safety Information 1 Pcs
User Guide Info Card 1 Pcs

Optional Accessories(To be ordered separately)

Item Name Description
1 OAW-AP-MNT-B Indoor mounting kit, Type B1(9/16″) and B2(15/16″) for

T-shaped ceiling rail.
2| OAW-AP-MNT-C| Indoor mounting kit, Type C1(Open
Silhouette) and C2 (Flanged Interlude), for other shaped ceiling rail mounting.
3| OAW-AP-MNT-W| Indoor mounting kit, Type W wall and ceiling mounting with screws.

Figure1: Product Packing

Inform your ALE sales representative of incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed. Additional mounting kits for use with the OmniAccess Stellar access points are sold separately. Contact your ALE sales representative for details.

Hardware Overview

The following sections outline the hardware components of the OAWAP1301 Series access point.
Figure 2: OAW-AP1301 Front View

Alcatel Lucent AP1301 Series OmniAccess Stellar Access Point - figure
2

LED
The OAW-AP1301 Series access point is equipped with a hidden LED display that indicates different statuses with different colors.
For the details of the LED status, please refer to the Quick Start Guide.
Figure 3: OAW-AP1301 Back View

Table 1

1 Gigabit Eht1| lx 10/100/1000BASE-T autosensing (RJ-45) port, Power over Ethernet (PoE). In the case of only one WAN link, either EthO or Eth1 could work as WAN, EthO would be more preferred. In the case of two WAN links, EthO

  • Eth1 would be preferred.
    ---|---
    1 Gigabit LAN| lx 10/100/1000BASE-T autosensing (RJ-45) port.
    Console| RJ-45 female connector, default is RS-232 Console for Service Et Support only. Support software configures to RS-485 mode.
    USB| USB 2.0 host interface (Type C, output current 0.5A )
    DC Power Socket| DC 48V power jack, support powering AP through a designated AC-DC power adapter.
    Reset| Factory reset. Press the reset button for 5s, AP LEDs will quickly flash for 3s, then AP will restart and restore factory configurations.
    Security Lock Slot| The AP is equipped with a security lock slot for added security.

Table 2
Ethernet Port Pinout

Connector Pin Signal Name Function
1 RJ45_DA+ PoE-
2 RJ45_DA- PoE-
3 RJ45_DB+ PoE+
4 RJ45_DC+ PoE+
5 RJ45_DC- PoE+
6 RJ45_DB- PoE+
7 RJ45_DD+ PoE-
8 RJ45_DD- PoE-

Table 3

Console Port Pinout

Connector it Pin Signal Name Function
3 TXD Transmit
4 GND Ground
5 GND Ground
6 RXD Receive

Pins not listed are not connected.

Table 4
RS-485 Port Pinout

Connector

| Pin| Signal Name|

Function

---|---|---|---
| 1| RS4853| Data-
2| RS485_A| Data+
4| GND| Ground
5| GND| Ground
Pins not listed are not connected.

Note: The serial console port allows you to connect the AP to a serial terminal or a laptop for direct local management. This port is an RJ-45 female connector with the pinouts described in Table 3.
Currently for use by Service & Support only.
Note: The RS-485 port allows you to connect the AP to a RS-485 terminal. The maximum allowable current of PSE 12V power output is 300mA. In addition, PSE 12V power output can be turned on and off by software. This port is an RJ-45 female connector with the pinouts described in Table 4.

Power
The OAW-AP1301 series access point supports a direct DC power adapter (48V DC nominal, sold separately) and Power over Ethernet (PoE).
The DC power connector port is located on the back of the device, as shown in Figure 3.
The PoE allows the Ethernet port to draw power from an IEEE 802.3at compliant source.
OmniAccess Stella AP supports the power adapter provided by ALE ONLY.

Before You Begin

Refer to the sections below before beginning the installation process.
Pre-installation Checklist
Before installing your OAW-AP1301 Stellar access point, be sure that you have the following items:

  • 8-conductor, CAT5, or better UTP cable of the required length.

  • One of the following power sources:◼
    • IEEE 802.3at compliant Power over Ethernet (PoE) source (PoE switch or PoE injector).
    • AC-DC adapter (sold separately), output voltage DC 48V, output current ≥0.6A

  • A terminal or a notebook

Identifying Specific Installation Locations
You can mount the OmniAccess Stellar AP on a ceiling rail or on a wall. You should first determine the location of the installation. The installation position is located at the center of the required coverage area and should be free from obstructions or obvious sources of interference.

  • Minimize the number of obstructions (such as walls) between the AP and user terminals.
  • Electronic equipment or devices (such as microwave ovens) which may produce radio frequency noise should be away from the installation position of the AP.

It is strictly prohibited to install around stagnant water, water seepage, leakage, or condensation. Avoid cable condensation or water seepage along the cables connecting to the AP.

AP Installation
Refer to the mounting kits installation Guide.

Verifying Post-Installation Connectivity
The LED on the AP can be used to verify that the AP is receiving power and initializing successfully.

Product Specifications

OAW-AP1301 series Dimensions/Weight
Unboxed OAW-AP1301:

  • Net Weight: 1.64lbs / 0.74kg
  • Dimensions (HxWxD): 7.1 inches x 7.1 inches x 1.42 inches (18 cm x 18cm x 3.6cm)

Environmental

  • Operating :
    ▪ Temperature: 0°C to +50°C (+32°F to +122°F)
    ▪ Humidity: 10% to 90% non-condensing

  • Storage and transportation :
    ▪ Temperature: -40°C to +70°C(-40°F to +158°F)

For additional specifications on this product, please refer to the Datasheet.

Contacting Alcatel-Lucent Enterprise

Website Support


Main Site| https://www.al-enterprise.com/
Support Site| https://businessportal2.alcatel-lucent.com
Support Email| ebg_global_supportcenter@al- enterprise.com

Telephone Support

North America| 1-800-995-2696
Latin America| 1-877-919-9526
Europe| +800 00200100 (Toll Free) or +1(650)385-2193
Asia Pacific| +65 6240 8484
Other Region| 1-818-878-4507

https://www.al-enterprise.com
The Alcatel-Lucent name and logo are trademarks of Nokia used under license by ALE. To view other trademarks used by affiliated companies of ALE Holding, visit https://www.alenterprise.com/en/legal/trademarks-copyright. All other trademarks are the property of their respective owners. The information presented is subject to ALE without notice. Neither ALE Holding nor any of its affiliates assume any responsibility for inaccuracies contained herein. (2020)

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Alcatel-Lucent User Manuals

Related Manuals