SHENZHEN SUNVEYTECH CO LTD MYTB703 Wireless 7 Inch Monitor with Cameras System User Manual

SHENZHEN SUNVEYTECH CO LTD MYTB703 Wireless 7 Inch Monitor with Cameras System User Manual

What’s in the Box?

1. 7’’ monitor
2. HD camera
3. Solar camera
4. Car charger
5. U-shaped bracket
6. Screw(x4)
7. Power cable（x3）
8. Sunshade
9. Antenna(X4)
10. Accessories
11. Bracket
12. Iron sheet and 3M glue

NOTE 1: The contents included may be different based on the kit you purchased. Please take the actual product as standard.
NOTE 2： Antenna is divided into 2.4G wireless/433 codepair remote control(Please install it to the corresponding position)

Introduction

Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty.

Thank you very much for purchasing a Rear View Backup Camera System. With this manual you will be able to properly install and operate the unit.
The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle. The Backup Camera System should not be used as a substitute for the standard rear view mirror or for any other mirror that exists in your vehicle. In some jurisdictions, it is unlawful for a person to drive a motor vehicle equipped with a TV viewer or screen located forward of the back of the driver’s seat or in any location that is visible, directly or indirectly, to the driver while operating the vehicle.

Monitor Operation

1. Power key (control camera)
2. Switch channel
3. 1.Enter the menu and move to the left 2. Reduce brightness
4. 1.Menu key/Back key 2.Long press to enlarge (1X 1.5X 2.X 3X)
5. 1.Brightness Plus 2.(Enter the menu) Right select 3.plus
6. 1.Confirm key 　2.Start/pause recording (after card insertion) 3.Long press to adjust the V/H/W mode of the vehicle ruler
7. Vehicle ruler shortcut key

Remote control function?

1. 1. Confirm key

2. After entering the menu for confirmation
3. Start/pause recording (after card insertion)
4. 1. Power on key
5. 1. Vehicle ruler shortcut key
6. 1. Enter the menu and move to the left
7. Reduce brightness
8. Enter the menu and select from the left
9. 1. Menu key
10. 1. Brightness Plus
11. (Enter the menu) Right select
12. Enter the menu and right select
13. 1. Switch channel
14. CH1—CH2—CH3—CH4 (Split screen)
15. 1. Display channel CH1 screen
16. 1. Display channel CH3 screen
17. 1. Display channel CH2 screen
18. 1. Display channel CH4 screen

Video recording function

Open the SD card slot on the monitor back with the small bluescrew-driver , insert the adapter and micro SD card for recordingHigh-speed SD card of class 10 or above ( Less than 128G ) isrecommended

Please make sure to UNLOCK the Adapter before inserting the SD CardThe format al location unit of the micro SD card should be set in EXFAT32 / 64KB , other value is not compatible for the recording function

Please format the memory card for the first time

Plug in the card to start recording(“ENTER” to turn on/off recording) Recording: REC

Installation Diagram

Monitor Installation

Choose a monitor location in your vehicle that does not block your view and complies with local laws for safe driving. Do not place in an area where it might interfere with driving.

Camera Installation

Suitable Installation Position

Connection method

1. Car charger connect to wireless receiver in the monitor
   

2. “+”ACC/Fuse/radio

3. Camera is rechargeable
   

Charging instructions

1. The indicator will flash when charging
2. The red light flashes when the battery is exhausted
3. Four lights are always on, which means the battery is full

Pairing the Camera and Monitor

1. Select the channel to be pairing
   

2. Enter the menu and select pairing and press “ENTER” to confirm
   

3. 

4. Waiting for matching and drawing successfully
   

NOTE: when you need pairing,please confirm the circuit is properly connected and powered.If you need to pairing multiple cameras, please switch to the corresponding channel.

Connection mode

2.4G image signal transmission monitor power on/off
Remote control of two camera signals

The camera is turned on and off under the control of the monitor switch (when the monitor power is turned off, the camera will enter the standby state)

Specifications

CAMERA

SOLAR CAMERA

MONITOR

Troubleshooting

Check the fuse in the Cigarette socket adapter
Camera and Monitor won’t pair| Check if the camera is receiving power
Make sure to follow the instructions to operate the Pairing
Weak Signal| Check if the camera and monitor antennas are installed
Distance between camera and monitor is too great. Reduce distance between camera and monitor
Large dense objects could be obscuring the signal. If possible, move the objects
Interference from overhear power lines may be affecting the signal
Try unpairing and pairing
Night Vision is poor| **** The night sensor on the camera may be dirty or obstructed
Ensure the camera is installed at least 2 inches away from rear lights
Dark Picture| Check whether brightness and contrast are adjusted correctly

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>