Wabtec ASMB0878 Mini RF TOF Module Nanopan Instruction Manual
- June 6, 2024
- Wabtec
Table of Contents
Wabtec ASMB0878 Mini RF TOF Module Nanopan
2020 Wabtec Corporation. All rights reserved. The information contained in this publication is the property of Wabtec Corporation. This publication shall not be reproduced, redistributed, retransmitted, translated, abridged, adapted, condensed, revised or otherwise modified, in any form, in whole or in part, without the express written consent of Wabtec.
By accessing this, you agree that the information contained herein does not purport to cover all details or variations in Wabtec products or to provide for every possible contingency with installation, operation or maintenance. Should further information be desired, or should particular problems arise that are not covered sufficiently for the user’s purposes, the matter should be referred to Wabtec Corporation. Any applicable Federal, State or local or company safety or operating rules must take precedence over any information or instructions given in the Technical Documentation. Wabtec has no obligation to keep regulations the material up to date after the original publication.
WABTEC CORPORATION EXPLICITLY DISCLAIMS ALL WARRANTIES OF ACCURACY, MERCHANTABILITY OR FITNESS FOR ANY PURPOSE IN CONNECTION WITH THIS PUBLICATION AND USE THEREOF..
MANUFACTURER INFORMATION
INTRODUCTION
The product or product family described under scope of this document will be
henceforth referred to as DEVICE. This manual provides the information on the
DEVICE, its variants, specifications, operation, maintenance, decommission and
disposal.
SAFETY INFORMATION
The safety section includes safety precautions which must be observed when
working on items that appear throughout the manual. Examples of safety
precautions and labels are outlined below:
- Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
- Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury.
- Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
- Indicates a potential for equipment damage.
DISCLAIMER
These materials are provided for information purposes only, “as is” without
express or implied warranty of any kind. Wabtec makes no ANY EXPRESS OR
IMPLIED WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE OR
ANY OTHER EXPRESS OR IMPLIED WARRANTY REGARDING ANY PRODUCTS DESCRIBED in
these materials.
To the maximum extent permitted by law, Wabtec disclaims any and all implied warranties that might otherwise arise or apply, including any implied warranty of merchantability or of fitness for a particular purpose. Wabtec further makes no representation or warranty of accuracy of these materials and neither Wabtec will have no responsibility or liability for any error or omission in these materials. These specifications are subject to change without notice.
COMPANY DETAILS
Manufacturer:| Industrea Mining Technology Pty Ltd (trading as Digital Mining Technology)
3 Co-Wyn Close
Fountaindale, New South Wales, 2258 Australia
Telephone +61 2 8863 4730 GETProductionIMT@wabtec.com www.wabteccorp.com
Industrea Mining Technology Pty Ltd is a registered business subsidiary of Wabtec Corporation
---|---
OVERVIEW
GENERAL FEATURES
The ASMB0878 is a digitally controlled “Time of Flight” (ToF) ranging radio
module implemented on an industry standard M2.xx style circuit board. This
module can use used in a host controller board to provide a short range, power
limited UHF radio link for a variety of applications.
Key features include:
- Nanopan 5375 digitally controlled radio
- Power supply regulation/conditioning
- Serial interface
- Dual RF antennae ports under firmware control for antennae diversity
ABBREVIATIONS
ABBREVIATION | DESCRIPTION |
---|---|
ToF | Time of Flight |
N/C | Not Connected |
SCOPE & SPECIFICATION
FEATURE | DETAIL |
---|---|
Operating Frequency Band | 2.400 – 2.4835 GHz |
Maximum Transmit Power | 10 dBm at MMCX Pins |
Chipset | Nanopan 5375 |
Modulation | CSS |
Antenna Type | Two MMCX antenna pins for antenna diversity |
Antenna Gain
| FCC/ISED/RCM standard Compliance: Peak Gain +8 dBi max
EN Standard Compliance: Peak Gain +3 dBi max
Rated Voltage| 3.3 Vdc
Operating Temperature| -40°C to +75°C
Module Dimensions| 42 mm x 22 mm
PIN CONFIGURATION AND FUNCTION
Pin | Signal | Type | Pin | Signal | Type | |
---|---|---|---|---|---|---|
74 | Vsupply (+3.3V) | PWR | 75 | GND | PWR | |
72 | Vsupply (+3.3V) | PWR | 73 | RESERVED | N/C | |
70 | VIO | PWR | 71 | RESERVED | N/C | |
68 | VSTDBY | PWR | 69 | GND | PWR | |
66 | PWREN/#SDN | CMOS | 67 | RESERVED | N/C | |
64 | RESERVED-DBG | N/C | 65 | RESERVED | N/C | |
62 | I2C-BUSEN | CMOS | 63 | GND | PWR | |
60 | I2C-SCA | CMOS-OD | 61 | RESERVED | N/C | |
58 | I2C-SDA | CMOS-OD | 59 | RESERVED | N/C | |
56 | ID-CATEGORY | Passive | 57 | GND | PWR | |
54 | ID-VARIANT | Passive | 55 | RESERVED | N/C | |
52 | #RESET | CMOS-OD | 53 | RESERVED | N/C | |
50 | CLK32K | CMOS | 51 | GND | PWR | |
48 | RESERVED | N/C | 49 | RESERVED | N/C | |
46 | RESERVED | N/C | 47 | RESERVED | N/C | |
44 | RF_COEX | CMOS-OD | 45 | GND | PWR | |
42 | SYNC OUT | CMOS | 43 | RESERVED | N/C | |
40 | SYNC IN | CMOS | 41 | RESERVED | N/C | |
38 | UART-DTR | CMOS | 39 | GND | PWR | |
36 | UART-RTS | CMOS | 37 | RESERVED | N/C | |
34 | UART-CTS | CMOS | 35 | RESERVED | N/C | |
32 | UART-TXD | CMOS | 33 | GND | PWR | |
30 | MECH E KEY | 31 | MECH E KEY | |||
28 | MECH E KEY | 29 | MECH E KEY | |||
26 | MECH E KEY | 27 | MECH E KEY | |||
24 | MECH E KEY | 25 | MECH E KEY | |||
22 | UART-RXD | CMOS | 23 | RESERVED | N/C | |
20 | UART-DSR | CMOS | 21 | RESERVED | N/C | |
18 | GND | PWR | 19 | RESERVED | N/C | |
16 | WAKE/#LPMODE | CMOS | 17 | RESERVED | N/C | |
14 | SPI-MOSI | CMOS | 15 | RESERVED | N/C | |
12 | SPI-MISO | CMOS(HiZ) | 13 | RESERVED | N/C | |
10 | SPI#SS | CMOS | 11 | RESERVED | N/C | |
8 | SPI-SCK | CMOS | 9 | RESERVED | N/C | |
6 | #IRQ | CMOS-OD | 7 | GND | PWR | |
4 | RESERVED | N/C | 5 | RESERVED | N/C | |
2 | RESERVED | N/C | 3 | RESERVED | N/C | |
1 | GND | PWR |
APPROVED ACCESSORIES LIST
The below table outlines the accessories that are approved for operation with this Module: For ToF Radio operation, this module has been tested and approved for use with the antenna listed below. The module may be integrated with other antennas of the same type and antenna gains of less than or equal than the approved.
For Countries using FCC/ISED/RCM Standard Compliance testing & test reports:
ANTENNA PART NO. | FREQUENCY | ANTENNA TYPE | PEAK GAIN |
---|---|---|---|
WA2-0243-N01SJ4-080 | 2.4 GHz | Omni-directional | +8dBi Max |
PROD0832 | 2.4 GHz | Omni-directional | +3dBi Max |
MISC0483 | 2.4 GHz | Omni-directional | +3dBi Max |
For Countries using EN Standard Compliance testing & test reports:
ANTENNA PART NO. | FREQUENCY | ANTENNA TYPE | PEAK GAIN |
---|---|---|---|
PROD0832 | 2.4 GHz | Omni-directional | +3dBi Max |
MISC0483 | 2.4 GHz | Omni-directional | +3dBi Max |
WARNINGS:
- Keep this Integration Manual for later reference.
- Do not leave this Module in an uncontrolled environment where the storage temperature is below-40°C (-40°F) or above 85°C (185°F). This may damage the DEVICE.
- Do not operate this Module outside specified temperature range. Refer to specification table for further information.
GENERAL INFORMATION
INTEGRATION
Module Integration should be in accordance with the procedures defined by
Digital Mining Technology and only performed by the manufacturer or authorized
representative. Host equipment must be configured to the modulation schemes to
comply with the modular approval listed in Sec. 2.3 and adhere to all local
regulations appropriate for automotive Installations in the end-user
geographic region.
MAINTENANCE
This equipment is not intended to be maintained by the end user. Opening the
enclosure should not be attempted, will void any warranty and could compromise
the safe operation of the unit. No user-serviceable parts. Contact your local
authorized representative for service arrangements.
DECOMMISSION AND DISPOSAL
Power should be disconnected before decommissioning. The unit must not be treated as general waste. By ensuring that this product is disposed of correctly, you will be helping to prevent potentially negative consequences for the environment and human health which could otherwise be caused by incorrect handling of this product.
Waste Disposal Method: Recycling is encouraged. Dispose of in accordance
with local, state and federal laws and regulations.
USA: Dispose of in accordance with local, state and federal laws and
regulations.
Canada : Dispose of in accordance with local, state and federal laws and
regulations.
EC : Dispose of in accordance with relevant EC Directives.
AUTHORIZED REPRESENTATIVES
Australia Industrea Mining Technology Pty Ltd,
Telephone +61 (2) 8863 4730
Trading as Digital Mining Technology
3 Co-Wyn Close
GETProductionIMT@wabtec.com
Fountaindale, NSW, 2258
www.wabteccorp.com Australia
Brazil Wabtec Brasil Fabricação e Manutenção
Telephone +55 (31) 2103 5348
de Equipamentos Ltda
Avenida General David Sarnoff
Fax +55 (31) 2103 5100
n 4600 Cidade Industrial Contagem, MG
www.wabteccorp.com 32210-110 Brazil
Canada Wabtec Transportation Canada Inc
Telephone +1 (905) 251 0074
27047 Oakwood Road, Oakbank, Manitoba, R0E 1J2 www.wabteccorp.com Canada
India Wabtec India Industrial Private Ltd
Telephone +91 (080) 6838 7816 ITC Green Centre
6th Floor, Southwest Tower www.wabteccorp.com No.18, Banaswadi Main Road, Maruthisevanagar Bangalore, Karnataka, 560005, India
Indonesia PT Intecs Teknikatama Industri
Telephone +62 (21) 729 3351 Jl. Ciputat Raya No. 18D
Kebayoran Lama Selatan, Jakarta, 12240
Fax +62 (21) 729 3352 Indonesia www.intecs.co.id
Mexico Comercializadora Minera Norte, S.A. DE
Telephone+52 (878) 783 8215
C.V +1 (830) 352 5519 Ave. H. Colegio Militar No. 2000-B Col. Las Fuentes
Piedras Negras, Coahuila
Fax+52 878-783-8218 México. C.P. 26010
www.cominsa.com.mx
North **America Digital Mining
** Telephone +1 (480) 264 2063 2901 East Lake Road Erie, Pennsylvania, 16531
Fax+1 (480) 264 6402 USA
www.wabteccorp.com
Sub **Saharan ****Africa Probe Integrated Mining Technologies** Telephone+27 (11) 453 0924
(PTY) Ltd 245 Albert Amon Road
Fax +27 (11) 453 2141
Meadowdale, Germiston, 1614 South Africa
www.probebattery.co.za
PRODUCT APPROVALS AND REGULATORY INFORMATION
ASMB0878 module have modular approval and comply with FCC Part 15 and Canada Innovation, Science and Economic Development Canada (ISED) RSS-247 and RSS- Gen.
FCC ID: | YIY-ASMB0878 |
---|---|
IC: | 8903A-ASMB0878 |
Caution : Modifications to this product without written consent from the manufacturer or its designated authorized representatives could void the user’s authority to operate the equipment.
DECLARATION OF CONFORMITY 47 CFR § 2.1077 COMPLIANCE INFORMATION
We, Industrea Mining Technology Pty Ltd, T/A Digital Mining Technology, at 3 Co-Wyn Close, Fountaindale, NSW, 2258, Australia declare under our sole responsibility the products:
Trade Name: | Digital Mining Technology |
---|---|
Model Number: | ASMB0878 |
Product Name | Mini RF TOF Module Nanopan |
FCC ID: | YIY-ASMB0878 |
Responsible Party: | Digital Mining |
2901 East Lake Road Erie, PA, 16531 814-875-2234
Complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC INTERFERENCE STATEMENT FOR CLASS B DEVICES
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
A shielded type Ethernet cord is required to meet FCC Class B emission limits and prevent interference to the nearby radio and television reception. This device and its antenna(s) must not be co-located or operate in conjunction with any other antenna or transmitter. The antenna is considered an integral system component. Use of any antenna other than those specified in the installation manual or supplied with the product may void the product’s compliance.
FCC RADIATION EXPOSURE STATEMENT
To comply with FCC RF exposure limits for general population / uncontrolled
exposure, the antennas used for this transmitter must be installed to provide
a separation distance of at least 20 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter.
INDUSTRY CANADA COMPLIANT
This Class B digital apparatus complies with Canadian ICES-003. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CONCERNING RADIO TRANSMITTERS
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
INDUSTRY CANADA – RADIATION EXPOSURE STATEMENT
To comply with Industry Canada RF exposure limits for general population /
uncontrolled exposure, the antennas used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter.
AUSTRALIAN RADIO COMMUNICATIONS EQUIPMENT – RADIATION EXPOSURE STATEMENT
The equipment complies with the Radiocommunications (Electromagnetic Radiation
– Human Exposure) Standard 2014 for General Public Exposure, Non-Aware User,
for a Compliance Level 2 Radiocommunications Equipment, when the minimum
safety distance is adhered to, and shall bear the RCM.
DOCUMENT REVISION
DOCUMENT NO | REVISION |
---|---|
ASMB0878-HARDWARE INTEGRATION MANUAL- R1 | Original document |
ASMB0878-HARDWARE INTEGRATION MANUAL- R2 | Sec 2.3 & 2.5: Clarified antenna |
gain based on test standards
ASMB0878-HARDWARE INTEGRATION MANUAL- R3| Sec 2.1: Replaced Software design
radio to Digitally controlled
radio
|
DOCUMENT SIGN OFF
DOCUMENT REVISION NO.: Rev. 2
POSITION
| ****
Certification Engineer
DATE CREATED: By P C Shivalingam at 8:41 pm, Jan 28, 2022
POSITION
| ****
Design Engineer
DATE REVIEWED: By Peter O’Donnell at 4:32 pm, Jan 31, 2022
POSITION
| ****
Engineering Manager
DATE APPROVED: By Steve Clifton at 3:40 pm, Feb 01, 2022
References
- Inicio – Cominsa
- Home - Intecs Teknikatama Industri
- Renewable Energy - Inverters & Batteries | Probe Group
- Homepage | Wabtec Corporation
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>