COLOR KINETICS C-Splash 2 Submersible Spotlight with Intelligent RGB Light Instruction Manual
- June 6, 2024
- COLOR KINETICS
Table of Contents
- Installation Instructions
- Confirm all components received.
- Verify the electrical plan and all necessary surge protection
- Record the location and a serial number of each luminaire for
- Make sure power is OFF.
- Drain before mounting.
- Mount luminaires
- Connect luminaire cable
- PDS-150e wiring
- Turn the power ON.
- Address luminaires with QuickPlay Pro 2 software.
- Rotate and aim luminaire.
- Lock luminaires in place.
- Fill
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
C-Splash 2
Installation Instructions
A Must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations.
PUB-000142-00 (R08)
15 November 2021
Before installing this product, please visit the product page at www.colorkinetics.com for the latest version of the installation instructions. Due to continuous improvements and innovations, installation instructions may change without notice.
Confirm all components received.
Important Surge Protection Requirement:
www.colorkinetics.com/KB/surge-protection
Verify the electrical plan and all necessary surge protection
requirements.
Configuration Calculator: www.colorkinetics.com/support/install_tool
Calculates the number of luminaires each circuit can support based on: a model of luminaires, line voltage, circuit load, and cable lengths.
Connect luminaire within the maximum length.
Record the location and a serial number of each luminaire for
addressing.
Make sure power is OFF.
Drain before mounting.
Mount luminaires
Quantity = 3 3/8 in – 16 Silicon bronze cap screw and washer
Connect luminaire cable
PDS-60 wiring
Power / Data Supply | Maximum number of C-Splash 2 luminaires |
---|---|
PDS-60 | 2 |
PDS-150e wiring
Power / Data Supply | Maximum number of C-Splash 2 luminaires |
---|---|
PDS-150e | 6 |
UL / CE
From C-Splash 2 luminaires
CQC
From C-Splash 2 luminaires
Turn the power ON.
Address and Configure: https://www.colorkinetics.com/global/support/install- tool
Address luminaires with QuickPlay Pro 2 software.
Rotate and aim luminaire.
Do not look into the beam.
Do not loosen sealing bolts.
Lock luminaires in place.
Fill
Not for use in the human-occupied pool
Ensure that the main power supply is off before installing or wiring a
luminaire.
Do not attempt to install or use a luminaire until you read and understand
the installation instructions and safety labels.
Do not use a luminaire if the lens, housing, or power cables are damaged.
Do not attempt to open the luminaire. Risk of electrical shock and damage to
the water seal. No user-serviceable parts.
Do not use a luminaire for any voltage for which it is not rated. Do not
exceed the specified voltage and current input for any luminaire.
Do not hot swap luminaires. Ensure that power to the series is off before connecting or disconnecting individual luminaires.
Do not install in human-occupied underwater locations, such as pools and spas.
Do not remove or loosen sealing bolts or cable compression fitting.
Doing so will destroy the water-tight seal.
This product contains a light source of energy efficiency class G. For additional Energy Efficiency Class Information, please refer to https://colorkinetics.helpdocs.io/article/cviis2p8qq.
© 2021 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed.
References
- Color Kinetics Official Website | Homepage
- Understanding Surge Protection For LED Lighting Systems - Knowledgebase
- Installation Tools | Color Kinetics
- Color Kinetics Energy Label information - Knowledgebase
- Installation Tools | Color Kinetics
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>