Zhongshan Kaisen Technology A01 Smart Door Lock User Manual

Zhongshan Kaisen Technology A01 Smart Door Lock

Introduction

Technical Parameter

Battery Type

| 4pcs 1.5V AA dry batteries (No include)

R echargeable batteries are not recommended, b ecause most rechargeable battery’s voltage is 1 .2V.

---|---
Working Voltage| 4.5~6v
Unlock Ways| Bluetooth, Fingerprint, Passcode, Access Card, Key, Alexa (Need to match the gateway sold

separately ).

Scanner Type| LED 3D Live fingerprint sensor
FRR, FAR| ≤1%，≤0.001%

Work Environment

| Temperature：-20～60℃

Humidity：0～95%

Passcode Capacity| 150
Fingerprint Capacity| 120
Card Capacity| 200
Center Distance| 60mm or 70mm (2-3/4” or 2-3/8”)
Door Thickness| 35~55mm (1-8/3”~2-1/8”)
Passcode Length| 6~12digits
Unlock response time| 0.3s

Private Lock

Private mode

Only the administrators can unlock it by password, fingerprint, card, and backup key.

General mode

Every added user can unlock it by password, fingerprint, card, and backup key.

**Backup Key

**

Remove the cover cap (2 ways).

• Method 1: Press the end of the outer handle to pry up the cap.
• Method 2: Insert a needle into the little hole to push the cap off.

Insert the key and turn right 90 degrees. Press down the handle to open the door.
Notice: Please put the backup keys in another place.

Initialization

Remove the battery cover and press the “SET” button for 5 seconds, lock will sound ‘Please enter the initialization passcode’. The initial passcode is “000+ ”. The lock will sound ‘Delete administrator successful’ means that you have initialized the lock successfully.

Installation Guide

• Change Handle Direction Change the Handle to the direction that you need. Use the L wrench which in the accessories bag to remove the hex socket screw and change the direction.

**Overview

**

1.  Outer Handle
2.  Outer Lock
3.  Screws Pillar
4.  Data Wire
5.  Square Spindle
6.  PVC Sheet
7.  Latch
8.  Strike Plate
9.  Bottom Case
10.  Metal Plate
11. . Inner Lock
12.  Battery Cover
13.  Pin (fixed square spindle)

**installation Diagram

**

**Install the latch

**

1.  Adjust the length of the latch according to the distance from the door hole center to the door edge. (60mm or 70mm)
2. Insert the latch in the hole and tighten the screws.
3.  Install the bottom case and strike plate on the door frame. (Accessories numbered 8 and 9 on the page 5 Overview)

Install the outer lock with a square spindle

1. Select the suitable square spindle that fit your door thickness. (shorter : 35~45mm; longer: 45~55mm)
2. Find the little pin in the accessories bag. Install the square spindle, through the little hole with the pin to fix the spindle on the outer lock. Bend the bottom of the little pin to hold it in place. (Please be sure align the position of the little hole)

Get the metal plate

1. Find the inner lock and take off the battery cover.
2.  Remove these 3 screws.
3. Get the metal plate and PVC sheet.(Numbered 10 and 6 on the page5 Overview)

Install the outer lock

Let the data cable goes on the top of the latch. Make sure the square spindle and 2 screws pillar through the latch holes.

Install the metal plate

1.  Select the suitable screws that fit your door thickness. (shorter : 35~45mm; longer: 45~55mm)
2.  Install the metal plate to the door and tighten these 3 screws.

**Install the inner lock

**

1.  Connect the data cable to the inner lock.

2.  Install the inner lock on the metal plate and fasten it with 3 short screws to fix it on the door.

3.  Install 4pcs AA dry batteries. (No include)
   (Warm Tips: Rechargeable batteries are not recommended, because most rechargeable batteries’ voltage is 1.2 volts.)

4.  Install the battery cover and fasten it with 1 screw to fix it on the lock.

5. Check the keypad, fingerprint, OLED display are on power and can work properly.

Operation Programming

Pairing Lock to Phone App

Android Mobile Phone—Search “TTLock” from Google Play. Apple Mobile Phone please search “TTLock” from App Store.

Register and log in to the Account

Match the Lock to the Application

Please follow the steps below when you match the lock. Please turn on the phone Bluetooth. When you add a lock, you need to touch the screen of the lock after installing the lock and installing the battery, match the blue icon lock, and set the name for the lock.

Note: If the smart lock is in a non-addable state, please initialize the lock.(Refer to Page 4 Initialization)

TT LOCK App Operating

Account Information Change
Once the lock is added successfully, the TTLock App account becomes the administrator of the lock. And an administrator passcode for the lock will be generated at the same time. You can change the administrator passcode follow the steps below. Each account can be added with multiple smart device Locks for management.
Note: When the inner lock switches to the privacy mode (Refer to the Page 2 to learn about Private Lock), only the administrator passcode and the administrator APP account can unlock the lock.
Lock/Unlock
Press for unlocking, long press for the lock. lt requires your smartphone and Bluetooth lock to be within a certain range.
Send ekey
You can add another account on the app. This way your family can also control the Bluetooth lock via the app-Support authorized users to Limit time, Permanent, One-time, Recurring control smart Lock.
Note: The users also need to register the TTLOCK APP Account.
Generate Passcode
Generate or customize the passcode of the Bluetooth lock. Generate or customize permanent, one-time, time-limited, recurring passcode.
Note: Generate the passcode to clear the passcode that Bluetooth lock stored by “Erase”. Once used, in addition to the admin passcode.
(You can unlock the lock by inputting the password you have set + ）
e keys
Manage the authorized accounts in “Send eKey”. Admin can clear eKey, reset eKey, send eKey, etc.

Passcodes
It records all passcodes stored by the Bluetooth lock you had set. In addition, it can also reset, generate, upload passcodes.
(You can unlock the lock by inputting the password you have set + ）
IC Cards
You can match two types of IC cards: Permanent or Timed. Place the card against the card reader sensor on the smart Lock(keypad panel).
Fingerprints
You will be required to Place and Remove your finger to the sensor 4 times please follow the prompts.
Authorize Admin
You can authorize other TTLock App accounts as admin. After authorization is successful they will have the same functions as admin except for authorized admin.
Records
It records the time and manner of the smart lock when someone opens or closes. Manage your Bluetooth lock safely and efficiently.
Settings
It have the function about the Bluetooth Lock function setting, lock information setting, remote unlocking, auto-off time, lock sound, time proofread, record reading, etc.
You can find the information about the lock such as battery power, admin passcode. Note: The admin passcode will not be cleared when erasing the passcode, other passcode will be cleared.

If you forget to lock your door often, you could set “Auto-Lock”.
Set the time for automatic locking in your needs, so you don’t have to worry about security accidents due to being unlocked.
Remote Control
Remote control support needs an extra additional Wi-Fi Gateway(sold separately). Match the gateway, smartphone, app then the smart Lock can support the remote control lock.
Note: If you want to connect with Amazon Alexa, you need to buy a WIFI Gateway.

Add user by the lock

Note: Except for adding users through the TTLock App, you can also add users directly on the lock following the steps below. Remove the battery cover and press the SET button. Then please verify administrator by pressing  admin passcode +  ( you can view or set the administrator passcode fellow page 10.) Please enter fingerprint, passcode, or access card Fingerprint: press the same fingerprint, four 4 times. Passcode: press 6~12digits Passcode + , for twice. Access card: put an access card close to the keypad, for 1 time. After you create the first user, the system will automatically proceed to register the next user. You can continue to register more or touch the key to cancel it. Note: For the users that you add directly with the lock, please synchronize the data through the TTLock App follow the step below, so that you can also manage the users in the App. Operation: Select Setting Upload Data Start

Application FAQ

1. Q1. How to do if I cannot match the door lock (the name is gray) in the TTLock?
   A1. Try to initialize the lock. Please find the initialization on page 3 of the manual. And follow the steps on page 9 to pair the lock to TTLock App.

2. Q2. How to set the account Passcode?
   A2. TTIock – Upper left corner(menu button) -Settings – Click on your profile picture(edit) – Reset Passcode.(Refer to Page 10 Account Information Change)

3. Q3. How to set/check the admin passcode?
   A3. TTLock – Settings – Basics- Admin Passcode.

4. Q4. How to set auto-lock time?
   A4. TTLock – Settings – Auto-Lock. Please Calibrate Time in [Lock Clock] and Enter the [Firmware Update] to confirm that your APP is the latest version.

5. Q5. What is [Send e-key]?
   A5. Send e-key to authorize to other accounts. The recipient also needs to download TTLock and register an account. Recipients will have permission to control the lock via their phone APP.

6. Q6. How to Erase/Edit the guest passcode?
   A6. Erase: Generate Passcode – Erase- Click Generate – Enter this passcode on the keyboard and all guest Passcodes will be erased. Edit: Passcodes – Click on a code – You can edit in [Passcode].

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>