owon PIR323 ZigBee Multi-Sensor User Guide

June 9, 2024
owon

owon PIR323 ZigBee Multi-Sensor

Safety Handling

WARNING: Failure to follow these safety notices could result in fire, electric shock, other injuries, or damage to the ZigBee Multi-Sensor and other property. Read all the safety notices below before using the ZigBee Multi- Sensor.

  • Avoid high humidity or extreme temperatures.
  • Avoid long exposure to direct sunlight or strong ultraviolet light.
  • Do not drop or expose the unit to intense vibration.
  • Do not disassemble or try to repair the unit on your own.
  • Do not expose the unit or its accessories to flammable liquids, gases or other explosives.

Technical Specifications

Wireless Connectivity

  • ZigBee
    2.4GHz IEEE 802.15.4

  • ZigBee Profile
    ZigBee 3.0

  • RF Characteristics

    • Operating frequency: 2.4GHz
    • Range outdoor/indoor: 100m / 30m (Open area)
    • Internal PCB Antenna

Physical Specifications

  • Battery
    DC 3V (Two AAA batteries)

  • LED
    2-color LED (Red,Green)

  • Operating environment

    • Temperature: -10℃ ~+55℃
    • Humidity: ≤ 85% non-condensing
  • Detecting range(PIR)

    • Distance: 5m
    • Angle: up/down 100°left/right 120°
  • Dimensions

    • 62(L) × 62 (W)× 15.5(H) mm
    • Line length of remote probe: External temperature: 2.5m (Optinal)
  • Mounting Type
    Tabletop stand or Wal mounting

Welcome

The Multi-sensor is used to measure the ambient temperature & humidity with built-in sensor and external temperature with remote probe. It is available to detect motion, vibration and allows you to receive notifications from mobile app. The above functions can be customized, please use this guide according to your customized functions. This guide will provide you with an overview of the product and help you get through the initial setup.

Features

  • ZigBee 3.0
  • PIR motion detection (Optional)
  • Vibration detection (Optional)
  • Environmental temperature & humidity measuring (Optional)
  • External temperature probe(Optional): Available for water measurement
  • Low power consumption

Installation

You can mount the multi-sensor to the wall, ceiling or keep your multi-sensor on a bookshelf or table.

  • Please ensure that the surface is clean and secure.
  • You can peel off the tape on the back or lock it with screws.

PIR/Vibration/Environmental temperature & humidity function:

  1. Avoid mounting the Multi-sensor close to pets, air conditioners, heaters, sunshine or places where the temperature varies.
  2. You need to pay attention to the distance and range of the sensor when installing.

External temperature probe
Please refer to the mounting example below. You can measure the temperature by touching the probe with the measured object. Such as water, floor, metal etc. But don’t put it in the environment with strong acid and alkali

Get to know your device

LED indicator
The LED status gives the following information:

Reset button

Reset: Press and hold the reset button for 10 seconds until the LED light flashes three times at third second, and it will flash for three times again at tenth second.

Configure Network

To get started, you will need:

  • A Zigbee Gateway.
  • A mobile phone with a mobile APP installed.

Adding to the gateway’s network

  1. Set your gateway to permit joining (see your gateway’s manual).
  2. Power on the Multi-sensor and press the reset button once to make sure the LED indicator is flashing red (If not, reset it to factory defaults).
  3. Make sure the Multi-sensor is in the range of gateway’s network. After few seconds the Multi-sensor will join the gateway automatically and the LED indicator will flash green when it successfully joined.
    Note: If the adding is failed, simply reset the Multi-sensor and retry.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals