HINKLEY 902744FMM-LWD 44 Inch Trey Ceiling Fan Instruction Manual

HINKLEY 902744FMM-LWD 44 Inch Trey Ceiling Fan Instruction Manual

GENERAL INSTALLATION & OPERATION INSTRUCTIONS

1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning.
2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and products, secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installation(s) and connections.
3. WARNING: To reduce the risk of fire, electric shock, or other personal injury, mount fan only on an outlet box or supporting system marked acceptable for fan support of 35 lbs (15.9 kg) or less and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
4. Make sure that your installation site will not allow rotating fan blades to come in contact with any object. Blades should be at least 7 feet from floor.
5. Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in the carton until ready to be installed to protect its finish. If you are installing more than one ceiling fan, make sure that you do not mix fan blade sets, as each blade is part of a weighted set.
6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be spread apart with the common conductor and the grounding conductor on one side of the outlet box, and the “HOT” wires on the other side.
7. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed and should be installed per the light kit’s installation instructions.
8. After fan is completely installed, check to make sure that all connections are secure to prevent fan from falling and/or causing damage or injury.
9. The fan can be made to work immediately after installation – the bearings are adequately charged with grease so that, under normal conditions, further lubrication should not be necessary for the life of the fan.
10. To operate the reverse function on this fan, press the reverse button while the fan is running.

IMPORTANT SAFETY PRECAUTIONS

WARNINGS:

• Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting.
• Support directly from building structure.
• To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked “acceptable for fan support” and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
• Do not use an incandescent light dimmer. Do not use this fan with any transformer type fan speed control device.
• To reduce the risk of personal injury, do not bend the blade arms when installing them, balancing the blades or cleaning the fan. Do not insert any object(s) between rotating fan blades.

NOTE:
The important precautions, safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and carefulness are factors which cannot be built into this product. These factors must be supplied by the person(s) installing, caring for and operating the unit.

TOOLS & MATERIALS REQUIRED

• PHILLIPS SCREWDRIVER
• FLAT SCREWDRIVER
• WRENCH OR PLIERS
• WIRE CUTTER
• STEPLADDER
• WIRING SUPPLIES AS REQUIRED BY ELECTRICAL CODE

UNPACKING YOUR FAN

UNPACK YOUR FAN AND CHECK THE CONTENTS.

• Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged.
• Examine all parts. You should have the following:

| TREY PACKAGE CONTENT
---|---
1| Blade Set of 3| BL902744Fxx
2| Blade Support Plates| In Hardware Bag
3| Mounting Bracket| MB902752
4| Decorative Ring| CT902752Fxx
5| Fan Housing with Motor*Remove rubber shipping supports around motor, if applicable. Save the screws.| X
6| Adapter Plate| X
7| 16W LED Assembly| E902752LED
8| Glass Shade| GL902752OPET
9| Receiver Incl. 5 Wire Nuts| CN902744
10| Wall Control w/12v Battery Wall Plate, Face Plate,2 Sets of Mounting Screws,and Machine Screws| 980013FAS
11| Hardware Bag
Bracket Mounting  Hardware (wood screws, screws, lock washers,star washers, flat washers, wire nuts),Blade to Motor Screws w/Lock Washers, Balance Kit,Safety cable hardware (wood screw, flat washer)|

HW902752Fxx

NOTE: Design of parts shown above may look slightly different for your specific model of fan.| XX=FAN FINISH

PREPARATION

Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box.
DO NOT LAY MOTOR HOUSING ON ITS SIDE AS THIS COULD RESULT IN SHIFTING OF MOTOR IN DECORATIVE ENCLOSURE.

INSTALLING THE MOUNTING BRACKET

CAUTION: To avoid possible electrical shock, be sure electricity is turned off at the main power box before wiring. All wiring must be in accordance with National and Local Electrical Codes and the ceiling fan must be grounded as a precaution against possible electric shock.

1. Locate ceiling joist where fan is to be mounted, being sure location agrees with the requirements in the minimum clearance section of this guide. Wood joist must be sound and of adequate size to support 35 lbs. (See Page 1, Items 3 and 4).
2. If not already present, mount a UL listed outlet box marked “suitable for fan support” following the instructions provided with the outlet box. The outlet box must be able to support a minimum of 35 pounds.
3. Attach mounting bracket to outlet box using screws provided with the outlet box.

FAN INSTALLATION

DO NOT FORGET to turn off the power. Follow the steps below to properly hang your fan. Carefully lift the blower motor assembly (without the blades) into position by hooking the motor assembly onto the hook on the ceiling mounting plate, allowing it to hang freely. You are now ready to make the electrical connections.

ELECTRICAL CONNECTIONS

REMEMBER -Turn off the power! NOTE – Control must be installed within 30 feet of fan. Use the wire nuts supplied with your fan when making connections. Secure the connectors with electrical tape and make sure there are no loose connections or wire strands.

1. Insert the receiver into the top of the fan housing. (Fig. 1) For best performance, make sure the Black Antenna, on the end of the receiver, remains extended and not tangled with any of the electrical wires.
2. Make wire connections from the fan to the receiver unit. For this step use the bundle of 5 wires on the receiver. (Fig. 2)
   • Connect the YELLOW fan wire to the YELLOW receiver wire.
   • Connect the GRAY fan wire to the GRAY receiver wire.
   • Connect the RED fan neutral wire to the RED receiver neutral wire.
   • Connect the WHITE fan neutral wire to the WHITE receiver neutral wire.
   • Connect the BLUE fan neutral wire to the BLUE receiver neutral wire.
3. Connect the wiring from the ceiling to the receiver unit. (Use the 2 wire bundle on the receiver.) Secure with supplied wire nuts.
   • Connect the BLACK building supply wire to the BLACK receiver wire.
   • Connect the WHITE receiver neutral wire to the WHITE building neutral wire.
   • Connect the COPPER building ground wire to the YELLOW/GREEN fan ground wire. Also connect the two GREEN wires (from fan) to building ground wire.

FINISHING THE INSTALLATION

1. Move fan into position over the mounting bracket and secure with the 4 screws provided. (Fig. 1)
2. Raise the decorative ring up against the mounting bracket, the four supports inside the decorative ring should be placed against the four slots on mounting bracket, twist the decorative ring clockwise until snug (Fig. 2).

INSTALLING THE BLADES

NOTE: Remove any rubber supports that are installed for shipping.

WARNING: To reduce the risk of personal injury, do not bend the blades while installing, balancing the blades, or cleaning the fan. Insert the blade through the slot in the housing. Align the holes in the blade and the fan motor assembly and secure with the blade support plates and blade attachment screws with lock washers. Repeat this procedure with the remaining blades.

INSTALLING THE ADAPTER PLATE

1. Remove one of the three screws on the mounting hub located on the fan motor.
2. Loosen the other two screws.
3. Install adapter plate to mounting hub.
4. Line up the two slotted holes with the two loose screws on the  mounting hub located on fan motor.
5. Re-install the third screw removed and tighten all three

INSTALLING THE LED ASSEMBLY AND GLASS SHADE

WARNING: Before starting installation, disconnect the power by  turning off the circuit breaker or removing the fuse at fuse box. Turning power off using the fan switch is not sufficient to prevent electric shock.

1. Remove the 1 of 3 screws from the posts of the light kit decorative housing and keep it for future use. Loosen the other 2 screws. (Do not remove)
2. While holding the LED assembly under your fan, make the polarize plug connections: (Fig. 2)
   • Red to white
   • Black to black
3. Place the key holes on the LED assembly over the 2 screws previously loosened, turn the LED assembly until it locks in place at the narrow section of the key holes. Secure by tightening the 2 screws previously loosened and the one previously removed. (Fig. 1)
4. Raise glass shade up against adapter plate and secure it to the fan by turning the glass shade clockwise until snug. DO NOT OVERTIGHTEN.
5. Restore power and your light kit is ready for operation.

 INSTALLING THE WALL CONTROL

REMEMBER to turn off the power before you begin.
NOTE – Control must be installed within 30 feet of fan.

1. Remove the existing wall plate and the old switch from the wall outlet box. (Fig. 1)

2. Connect the wiring from the wall switch receptacle to wall transmitter unit
   Connect one BLACK wire from the wall to one BLACK wire (labeled “TO FAN”) from the wall transmitter.
   Connect the other BLACK wire (labeled “TO POWER SUPPLY”) from the transmitter to the remaining BLACK wire from the wall (A/C supply source).

3. Connect the green ground wire form the switch to the ground wire on the wall outlet box.

4. Install the wall transmitter on the existing wall outlet box using the screws provided. Attached the wall plate with the mounting screws to finish the installation. (Fig. 2)

OPERATION

Your DC brushless motor is equipped with an automatically learned type remote control. There is no frequency switches on the receiver or transmitter. The fan can start to use once the pairing process is done. Remove the panel from the transmitter and then install one 23A/12V battery (included). To prevent damage to transmitter, remove the battery if not use for long periods of time (Fig. 16).

1. I, II, III, IV, V and VI button: These six buttons are used to set the fan speed as follows:
   I = minimum speed
   II = low speed
   III = medium low speed
   IV = medium speed
   V = medium high speed
   VI = high speed

2. button: This button turns the fan off.

3. Reverse button: This button is to control fan direction. This button must be pressed while fan is running (suggested speed IV)

4. Light button: This button is to control optional light. Switch the “D” and “ON” dip switch on the front of transmitter to decide the light in “ON/OFF” or “Dimmable” condition.

5. “SET” code setting button: Follow the below steps to use the set button. (Fig. 1)

6. ON – OFF Slide button: Power switch. (Fig. 2)

7. Signal light (Fig. 2)

Summer Mode and Winter Mode Operation

Summer Mode (forward):
A DOWNWARD airflow creates a cooling effect as shown in Figure 3. This allows you to set your air conditioner on a warmer setting without affecting your comfort.

Winter Mode (Reverse):
An UPWARD airflow moves warmer air off the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler setting without affecting your comfort

CARE AND CLEANING

Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking or humming sound during operation. This is especially true in climates with broad temperature and humidity ranges.
When dusting the blades, you must support the blade to prevent bending – no pressure should be applied to the blades. If you experience any flaws in the operation of your fan, please check the following points.

TROUBLESHOOTING

CAUTION: Switch off power supply before carrying out any of these checks.

FAN WILL NOT START

1. Check circuit fuses or breaker
2. Check wall control LED indicator light. If LED is not illuminated when pushing a button, it is not transmitting signal. Please check power to wall control/circuit breaker and all electrical connections.
3. Assure there are no more than 2 fans operating on a circuit through the wall control. Assure that there are more than 12 fans operating on a circuit through an on/off wall switch or a breaker (not through a wall control).
4. Assure that the fan in within range of the WiFi (150 ft.) or wall control (30 ft.
5. Check to assure only one fan is installed in the power circui.

FAN SOUNDS NOISY

1. Allow a 24-hour “breaking-in” period. Most noise associated with a new fan will disappear during this time.
2. Make sure all motor housing screws are securely fastened.
3. Make sure the screws that attach the fan blade to the fan are tight.
4. Make sure your ceiling box is secure and rubber isolator pads are used between the mounting bracket and outlet box

FAN WOBBLES

1. Check that all blade and blade arm screws are secure.
2. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smoother operation.
3. Check to assure all dowrods to motor hardware and/or hanger ball are tight.
4. Make sure ceiling box is secure.

ENERGY GUIDE

AVERAGE PERFORMANCE AND ENERGY INFORMATION

ENERGY GUIDE

Estimated Yearly Energy Cost $5$3                          $34Cost Range of Similar Models (19” – 84”)• Based on 12 cents per kWh and 6.4 hours use per day• Yo u r co s t depend s o n rat e s an d use • Energy Use: 19 Watts| Airflow 2,918Cubic Feet Per Minute
• The higher the airflow, the more air the fan will move• Airflow Efficiency: 154 Cubic Feet Per Minute Per Watt
All estimates based on typical use, excluding lights| ftc.gov/energy
Airflow Shown Is a Weighted Average of High and Low Cubic Feet per Minute Based on Downrod

SPECIFICATIONS

SMART BY BOND

HINKLEY SMART FAN OPTIONS (SOLD SEPARATELY): https://bondhome.io/app In addition to the included wall control, you can control your Hinkley fan through the Bond app using the smart technology accessory controls SOLD SEPARATELY.

• To use the app, download it for free from the App Store or Google Play.
• Open the app to create your account. You can also login with your Facebook or Google account.
• Next, set up a WiFi connection. You will need the SSID and WiFi password for the network you want to connect to.
• You will receive a prompt to choose the finish of your fan and name your fan device.
• The app will walk you through the main screen and show you how to change fan speeds, dim the light, set timers or utilize breeze mode.

NOTE: Maximum of 2 fans can operate on a circuit through the wall control. Maximum of 12 fans can operate on a circuit through an on/off switch or breaker when utilizing the app for the fan control (without the wall control in the circuit)

HINKLEY IS PROUD TO PROVIDE YOU WITH CEILING FAN PRODUCTS THAT ENHANCE YOUR SPACE WITH COMFORT, PURPOSE AND STYLE. AS A FAMILY COMPANY, WE ARE COMMITTED TO DESIGN, PERFORMANCE AND QUALITY, AND WHAT’S IMPORTANT TO YOU IS PARAMOUNT TO US. FOR A COMPLETE ASSORTMENT OF OUR PRODUCTS AND SOURCE BOOKS, VISIT HINKLEY.COM.

GLOBAL HEADQUARTERS
33000 Pin Oak Parkway | Avon Lake, Ohio 44012
T (440) 653 5500 | F (440) 653 5555 | hinkley.com

References

• How To Use the EnergyGuide Label To Shop for Home Appliances | Consumer Advice
• HINKLEY - Lighting and Ceiling Fans
• Bond Home app | Bond

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>