BOSCH F5CP32 Chassis Systems Control User Manual
- June 6, 2024
- Bosch
Table of Contents
BOSCH F5CP32 Chassis Systems Control
Description of F5CP32 parts
Operation principle of the F5CP32
The radar sensor‘s purpose is detection of objects and measurement of their
speed and position relative to the movement of the vehicle in which it is
mounted. F5CP32 senses targets by emitting many short frequency modulated
waves using the transmit antennas while receiving waves reflected by targets
using the receive antennas.
Distance and relative speed are determined by measurement of signal’s travel time and Doppler shift. Direction of the target is determined by using phase difference of the received signal between different Rx antennas. Using the Bosch chirp sequence radar modulation, the F5CP32 allows unambiguous determination of relative speed in a single measurement cycle. Therefore, no complex object models are needed for ambiguity resolution. The values calculated from detected radar reflections are basis for building a comprehensive model of the sensed environment.
User information
General description
The F5CP32 radar sensor and control unit (SCU) contains a FMCW radar
transceiver operating in the globally harmonized frequency range of 76.0 –
77.0 GHz. It senses targets by emitting many short frequency modulated waves
using the transmit antennas while receiving waves reflected by targets using
the receive antennas. Distance and relative speed are determined via beat
frequency (due to travelling time of the waves) and phase differences between
ramps (due to change of distance in short time). By using the antenna diagram,
the angles of departure and arrival of the radar waves can be determined.
Fitted in front of the vehicle, the F5CP32 monitors continuously vehicle
surroundings, supporting driver and vehicle systems with emergency braking,
cruise control and distance indicator.
Areas of application
The F5CP32 is the base for range of safety and driver assistance functions. In
particular, the F5CP32 can be used for the following functions: emergency
braking. If the driver does not react to the hazardous situation, the system
warns the driver via an audible and/or visual signal, followed by a short but
noticeable brake jerk.
The system then initiates partial braking to reduce the speed and give the driver valuable time to react. As soon as the driver presses the brake pedal, the system provides braking support. To do this, the system continuously calculates the degree of vehicle deceleration required to avoid the collision. If the system detects that the driver has failed to apply sufficient brake force, it increases the braking pressure to the required level so that the driver can attempt to bring the vehicle to a standstill before a collision occurs. If the driver fails to react to the immediate risk of collision, and the predictive emergency braking system detects that a rear-end-collision is unavoidable, it can – working conjunction with a video camera – automatically initiate full braking. As a result, the vehicle is traveling at significantly reduced speed when the collusion occurs, reducing the severity of the crash for the passengers of both vehicles.
If the predictive emergency braking system detects that the distance to a moving or stationary vehicle in front is becoming critically short, it prepares the braking system for a potential emergency braking procedure. If the driver fails to react to the critical situation, the system can automatically initiate full braking in an attempt to prevent the collision. If the rear-end collision is unavoidable, this action can at least minimize the severity of the collision, reducing the risk of injury to the passengers of both vehicles.
Adaptive cruise control (ACC)
The F5CP32 makes it possible to detect vehicles merging at an early stage –
making it the ideal extension of front radar (like FR5CP) for ACC systems. The
ACC system automatically maintains a set distance from the vehicle ahead by
automatically reducing the power to the engine, braking or accelerating. The
ACC stop & go variant can also automatically apply the brakes until the
vehicle comes to a standstill and will resume automatically when instructed by
the driver.
Heading distance indicator
This function measures the distance from the objects around vehicle and,
depending on the speed at which the vehicle is travelling, warns the driver
when the safe distance from the vehicle in front is not being maintained. The
function does not intervene independently, but instead informs the driver of
the distance from other vehicle via a visual and/or audible signal.
Sensor data fusion
The F5CP32 can support sensor data fusion without the need for additional
hardware. Sensor data fusion combines the benefits of different sensors and
measuring. principles in the most effective way possible, providing data that
individual sensors working in isolation are unable to generate. Fusion of
multiple sensors increases the measurement range, reliability and accuracy.
Video sensors, such as the multi-purpose camera or the stereo video camera
from Bosch, are the ideal supplement to radar technology. Using software
algorithms, the fusion of sensor data generates a detailed “image”, which
forms the basis for an interpretation of the vehicle`s surroundings.
Sensor fusion enables the implementation of additional assistance and safety functions, such as pedestrian protection (“AEB Pedestrian”). The function for predictive pedestrian protection meets the safety requirements as specified by Euro NCAP. It continually monitors, in combination with a video camera, the area around vehicle in order to detect impending collisions with pedestrians who are in the path of the vehicle or moving toward it in a way that is likely to present a risk. If the function detects that pedestrians are at risk, it can actively trigger application of the brakes in order to considerably reduce the risk and the consequences of the collision, or to prevent the accident altogether. Sensor data fusion can also be used to significantly improve the performance of the comfort functions. Thanks to the high degree of lateral measuring accuracy of a video camera, the ACC function is able, for example, to detect vehicles merging at an earlier stage, and therefore respond in a more dynamic manner. The system also ensures that vehicles in front are assigned to the correct lanes, which further enhances ACC functionality, especially when cornering.
National Statements
Canada
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device must not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
United States
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by Robert Bosch GmbH may void the FCC authorization to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Radiofrequency radiation exposure Information:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Vehicle integration
This chapter describes the requirements for all parts mounted in front or
around the sensor, like painted bumper, unpainted cover and emblem/radome,
regarding RF integration at 77 GHz with FR5Plus radar sensors. If these
requirements are not met, the sensor performance can be degraded. Values are
marked with t.b.c. or t.b.d. showing that they have to be confirmed or defined
during the development process. As product development is an on-going process,
we reserve the right to make amendments in line with technical progress.
The radar sensor performance should be influenced as low as possible by the installation behind a fascia. Therefore the two-way radar loss by the fascia should be as low as possible and the reflection attenuation must fulfill the requirements listed below. Vertical misalignment will cause additional attenuation reducing the maximum range. Horizontal misalignment will cause reduced detection at higher azimuth angles. Ghost target detection caused by interference signals of multiple reflection at fascia and metallic parts of the vehicle must be avoided. A simulation can be offered to evaluate the risk and the need of using absorber material to suppress this unwanted signal. Because the threshold of detection is very low, a high attenuation is required. Plastic material can only achieve high enough attenuation, if carbon black is added.
Radar cone
The radar cone describes the zone where the fascia has to be optimized. Any
parts of the vehicle inside the radar cone may influence the radar
performance. Cables, brackets, bars etc. should not touch the radar cone. The
fascia in this zone may not have bends and edges as well as changes in
thickness or material or painting.
Based on the footprint on the top side of the radar PCB the cone is
characterized by a vertical and a horizontal opening angle. The footprint is
centered regarding to the sensor housing. A CAD model of the radar cone is
available. The footprint for radar cone has the following dimensions: (W x H)
55 mm x 55 mm.
The horizontal opening angle depends on the angle range that is evaluated by the sensor in azimuth and elevation, whereby the opening angle of the radar cone has to be larger than the angle range that is evaluated. For covered integration the radar cone is 10° larger than the used angle range that is evaluated by the sensor.
Radar cone:
- ±80° (1) (tbc) in horizontal direction (not including misalignment)
- ±20° (tbc) in vertical direction (not including misalignment)
- Valid for angle measurement range of ±70°.
Fascia design guidelines
Material
Material with low dielectric constant (εr) and low dielectric loss factor tanδ
at 77 GHz should be used. Recommended are materials based on polypropylene
(PP) and polymethyl methacrylate (PMMA), while materials like polycarbonate
(PC) and acrylonitrile butadiene styrene (ABS) are still ok. The material
shall be homogenous, compounds including glass fiber, carbon fiber or metal
particles are not recommended.
The fascia shall be designed for radar transparency. The thickness shall be a multiple of the half wavelength (in the material) to minimize the influence of the fascia. The quality criteria of radar transparency is the reflection coefficient of the radome/fascia. Tolerances of the overall thickness and the dielectric constant of the used material influence the amount of reflection at the radome/fascia. Additional influence occurs due to curvature of the fascia. Therefore the radius has to be as large as possible. With sharp edges the negative influence will increase significantly. Not allowed are ribs, structures and steps changing the thickness of the radome/fascia.
Painting
The layer structure of the painting, typically made of three painting layers consisting of primer, base coating and clear coating, will increase the effective permittivity value εr,eff and dielectric loss factor tanδ of the painted plate used as fascia.
Fascia Classification (F5CP32)
The two-way radar loss caused by the fascia should be as low as possilbe. High
losses decrease the sensor performance regarding range and angle estimation.
Therefore it is recommended to achieve a two-way radar loss below 4
dB(t.b.c.). This corresponds to a loss of 20% of sensor range.
Classification of reflection caused by the fascia
- Reflection coefficient <-10 dBis achieved when fascia has optimized thickness within a tolerance of ±0.2 mm and permittivity within a tolerance ±0.02. Dielectric loss factor tanδ shall be <0.03.2.Reflection coefficient <-6 dBis achieved when fascia has optimized thickness within a tolerance of ±0.2 mm and permittivity within a tolerance of ±0.
- Dielectric loss factor tanδ shall be <0.05. This is the case for painted bumper especially when various colors are used.
- Reflection coefficient >-6 dBis achieved when fascia has no optimized thickness or a painting with high metallic content is used. The attenuation may exceed the maximum allowed limit.
The examples described in the classification of reflection are derived from evaluation of flat plates with constant thickness and homogeneous material. Deviations from this situation may cause a change in classification and the vertical tilt angle of fascia has to be increased.
Surface Properties of the fascia
The surfaces of the fascia shall not exceed an average roughness height of 20
μm (corresponding to ISO 1302 class N10; VDI 3400 class 45).
Installation hints
To enable the full performance of the radar sensor, it is recommended to use
the following installation hints and guidelines for the RF integration of the
sensor.
Maximum angle between radar cone and fascia
The angle α between the radar beam inside the radar cone and the fascia may
not be larger than 80° anywhere inside the radar cone.
Minimum distance between sensor and fascia
The minimum distance between the sensor radome and the fascia or any other
part of the vehicle may not be smaller than 5 mm. This is valid for fascia
parts fulfilling the following requirements.
Vertical tilt of fascia (F5CP32)
The vertical tilt angle between the sensor normal and the surface normal of
the fascia shall be in the range according to the following table.
Vertical tilt angle for high level functions (e.g. HWP, fCTA…):
Vertical tilt
| reflection
coefficient
| max. tolerance
thickness
|
tolerance ε r
|
tanδ
|
application
---|---|---|---|---|---
|
<-10 dB
|
±0.1 mm
|
±0.02
|
<0.01
| unpainted, (black) painting,
embleme
8°
|
-10 dB
|
±0.2 mm
|
±0.02
|
<0.03
| unpainted, (black) painting,
embleme
±0.1 mm
|
±0.2
|
<0.03
| painted
bumper
18°
|
-6 dB
|
±0.2 mm
|
±0.2
|
<0.05
| painted
bumper
Table: minimum vertical tilt angle of fascia to sensor normal for High Level functions (e.g. HWP, fCTA…)
Vertical tilt angle for low level functions (e.g. BSD, LCA A, DOW,…)
Vertical tilt
| reflection
coefficient
| max. tolerance
thickness
|
tolerance ε r
|
tanδ
|
application
---|---|---|---|---|---
|
-10 dB < -6 dB
|
±0.2 mm
|
±0.02
|
<0.03
| unpainted, (black) painting,
embleme
±0.1 mm
|
±0.2
|
<0.03
| painted
bumper
8°
|
-6 dB
|
±0.2 mm
|
±0.2
|
<0.05
| painted
bumper
| | | | |
Curvature of fascia for F5CP32
Curvature of the fascia may influence the radar performance, especially with
low vertical tilt angles. The minimum radius of the curvature shall be
according to the following rules:
- R > 350 mm, no significant influence expected
- R < 350 mm, significant influence possible, has to be evaluated
- R < 200 mm, significant influence expected, not recommended.
Absorber around the sensor
It is highly recommended to use a cone made of absorber material around the
radar cone of the sensor to prevent ghost targets. The design of the absorber
cone must fulfill the following design guidelines (reflection from outside the
radar cone, multipath reflection).
Reflection from outside the radar cone
Reflections from structures located outside the radar cone have to be avoided.
Furthermore interference signals picked up by the sensor antennas should be
avoided by keeping a minimum distance (d) of 5 mm to 10 mm for parts in front
of the sensor. Even with compliance to the radar cone, reflections at parts
outside the radar cone may disturb the received signal. Reflections at parts
causing an interference signal to the receiving antenna and reflections at
parts getting to the receiving antenna after a second reflection at the fascia
(multipath reflection). Closed surfaces of brackets and masks made of metal or
high reflecting material need a tilt angle being arranged that the reflection
is not received by the receiving antennas of the sensor.
For closed surfaces (masks) in azimuth, the angle γ between mask surface and the normal vector n of the sensor shall be above 75° for parts outside of the radar cone. For closed surfaces (masks) in elevation, the angle γ between mask surface and the normal vector n of the sensor shall be above 20° for parts outside of the radar cone.
Multipath reflection
Reflections of incoming signals at bracket or shielding absorber are coming
back to the sensor if reflection at the bumper occurs. The figure below shows
the situation which should be avoided. The worst case happens if the
combination of the vertical tilt angles of shielding and bumper is γ1 = γ2 / 2
. For a low interference signal the condition shall be:
γ1 > γ2 / 2 +10°
or
γ1 < γ2 / 2 -10°
The same requirements are valid for a horizontal tilt of the fascia.
Calibration
No manual alignment procedure is necessary, as the sensor performs it’s own
internal SW calibration.
References for Chapter 5 & 6 of this document:
TCD_F5CP32_Preliminary.doc
Version –preliminary- with date: –
Technical Data
- Product model name: F5CP32
- Frequency Band: 76-77 GHz
- Maximum Transmit Power: Nominal mean EIRP 21.4 dBm
- Maximum Transmit Power: Measured mean EIRP 21.23 dBm
- Maximum Transmit Power: Measured peak EIRP 30.25 dBm
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>