Shenzhen Cenwapet Technology C-collar S08 No-Bark Collar User Manual
- June 5, 2024
- Shenzhen Cenwapet Technology
Table of Contents
C-collar S08 No-Bark Collar
User Manual
Features
- Rechargeable: Rechargeable Transmitter and Receiver, with premium and efficient Li-Battery
- Waterproof: Transmitter is IPXS level, and Receiver is IPX7 level
- Multi-Modes: Shock, vibrate and beep are all available
- Dual Channels: One transmitter can control two receivers
- Easy Operation: Once turn on and pair successfully, begin to work
- Power Saving: If no operation within five minutes, change into standby state automatically
- Large Scope: Without any block, the valid distance can reach 650 yards
General Tips
- Please charge before first using, with the USB-micro5P wire in the Package
- Eliminate one misbehavior or obey one order at one time. If training gets too fast. your pet may become confused, even repel
- Before using shock mode, try to choose vibration to notice your pet
- Observing your pet s reaction, make sure the training intensity moderate
- Check the skin of your pet to avoid any hurt caused by shock
Key Definition
-
Antenna
-
Power Button
-
Channel 1/ Channel 2
-
LCD Screen
-
“+””-“
Shock Mode
Vibration Mode
Beep Mode -
Power Button
-
Belt Slot
-
Contact Points
Transmitter Instruction
- Short press the Power button to turn it on, and long press for 3 seconds to turn it off.
- In a power-on state, the following functions are available: shock, vibration, beep, level adjust by ‘+/- change the channel via the ‘ 1/2 ‘ button.
- In the power-on state, “+/- “is only available for shock level selection. Once press vibrates button. you can adjust the vibration level within 5 seconds. Then it will exit automatically.
- In power•on state, press an action button, and the corresponding symbol, and the indicator will flash on the LCD.
- In the power-on state. LCD will display the battery volume, if the battery bar is empty and keep flashing, it means low battery and need to be charged.
- In charging. the LCD battery bar will bounce one by one. Once charging is finished, the battery bar will show full and stop beating, meanwhile, the charger will be turned off automatically.
Receiver Instruction
- The short press the power button, the sound will beep once /twice
- In a power-on state, shock, vibration, and beep are all available
- In the standby state, the green light flashes every 3 seconds If no order is received within 5 minutes, it will change into deep sleep automatically, and the wake-up time is 3 seconds. Long press the action button on the remote transmitter for 3-5 seconds, it will be waked up.
- If battery power is lower than 3.2V, the red light will flash to remind you to charge it. Once battery power is lower than 3V, it will turn off automatically to protect the battery from over- discharged.
- During charging the green light is in a breathing state, once the charge is finished, the green light will keep on for 10 seconds and then extinguish automatically, which means full-charged, and then the charger will be turned off automatically.
How to pair the Transmitter with the Receiver?
- Ensure the remote transmitter and receiver are both on
- Long press the ON/OFF button on the receiver for 3 seconds, with the green light flashing slowly. Then press any action button on the remote transmitter, once the signal is received by the receiver, the green light will extinguish with one beep, which means successful pair. now you can control the receiver with your remote transmitter.
- One remote transmitter owns two channels, each channel can pair with several receivers.
- One receiver can only be paired with one channel, once you choose another channel to pair, the previous ID will be covered automatically.
Notice: Please remember the paired channel, if not paired you can’t control it.
Install the Contact Points & Conductive Silicone
-
Select the correct Contact Points and Conductive Silicone length for your dogs’ coat type:
a)For dogs with thicker coats, use 2 pcs longer Contact Points and Conductive Silicone
b)For dogs with shorter coats, use 2 pcs shorter Contact Points and Conductive Silicone -
Insert the Contact Points into the ports of the collar, use the Test Lamp with the inner hex key to rotate clockwise to tighten them
-
Install the Conductive Silicone onto the Contact Points to make it softer, which will be better for dogs’ skin
How to test the static shock function?
-
Take out the test bulb from the package, then put it on the Receiver Collar” s contact points
-
Press the shock button, if the test bulb lights, it means shock mode is available
-
Besides, the inner hex key on the test bulb, with the same size of the contact points, is designed to tighten or lose them.
Notice: Two sizes of contact points are available, please choose the right column according to your pet and its hair length.
How to Assemble the Collar Strap?
- Unhitch the nylon belt and take off the Slide Buckle
- Thread the strap through the Receiver Collar
- Thread the slide buckle through the strap
- Thread the strap through the side release buckle
- Thread the remaining strap through the slide buckle to make sure the collar strap is tight
FAQ
Q: The length of the belt collar? A: 25 inch
Q: How weight dogs do this training collar suit for?
An Over 20 pounds
Q: Is the receiver waterproof?
A YES
Q: How long my dog get training each time?
A.10-15 minutes
Q: What should I do if the training collar set does not work well? A
- Check the battery of the remote and receiver, if low power, please charge it
- Check the receiver, make sure it is opened
- Check the channel, if choose another, press 1/2 button to adjust
- Check the Contact Points, if too short, change to install longer ones
- Pair the transmitter and receiver again
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.