KUCCHERO F10 Portable Bluetooth Speaker User Guide

June 6, 2024
KUCCHERO

KUCCHERO F10 Portable Bluetooth Speaker

Product Overview

How To Pair

  1. Long press the power button for 2 seconds, It will power on and automatically enter the Bluetoolh mode. You will hear a voice prompt “Bluetooth mode, Bluetocth pairing”. The LED light will quickly flash red and blue alternatively when it is wait for pairing.
  2. On your device, enable Bluelocth and tap “BEAT BOOM” and pair.
  3. Once paired successfully, you will hear a voice prompt “Bluetocth connected”. The LED light will tum to a color-changing breathing light that cycle through multiple colors.

How To Control

  1.  Short press the •+ • or• – • button to adjust the volume.
  2.  Long press the ” + ” or • – ” button to skip to the previous track or next track.
  3. After pailing or during playback, short press the light effect button on the back to enable or disable the light effect

Tapping Function (Adding Sound EffectSJ)

The BEAT BOOM speaker allows you to tap different surfaces of the speaker to add sound effects to your music. Long press both the • + “and • – • buttons lo enable or disable the tapping function. Short press both the• + •and” – • buttons to cycle through three sound effect modes: drumming sound, instrument sound, and nature sound. Tapping the five surfaces of the speaker will generate different sound effects in each mode. The type and volume of the sound effect change depending on which surface you tap and how strongly you tap it. When you tap the speaker, the speaker lights or the line light will fiash quickly.

Light Effects

EX-BASS Sound

  1.  Long press the -~ ” button to disconnect current Bl uetooth. Short press again to reconnect.
  2.  Short press the • ~ ” button, you will hear a prompt tone and it enters the EX-BASS mode. Short press again to exit the EX-BASS mode.

TWSMode

Pair two speakers in the following order.

  1. FirsUy, ensure the two speakers are powered off;
  2.  Secondly, turn on one BEAT BOOM ~ aker. Disconnect it from your device by long pressing the • BASS • button if you have paired them with your device;
  3.  Thirdly, tum on the other BEAT BOOM speaker. When the line light quickly flashes red and you hear the voice prompt ‘ Synced”, the two speakers are paired successfully;
  4.  On your device, enable Bluetocth and tap “BEAT BOOM’ and pair;
  5. Once paired successfully, you can control music playback from either speaker. Turn off one BEAT BOOM speaker, the other one will also be turned off.

Answer or End a Call

  1.  Short press the t> button to answer an incoming call. Short press the I> button again to end the call.
  2. . Long press the [> button to reject an incoming call.

Battery Indicator

KUCCHERO F10 Portable Bluetooth Speaker
1

To check the battery level, short press the power button

FCC Statement

This device complies with Part 1 5 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and c.an radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular inst.allation. If this equipment does cause harmful interference to rad io or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals