Uolfin 5106195 13.8 Inch Black Incandescent Semi-flush Mount Light Instruction Manual

Uolfin 5106195 13.8 Inch Black Incandescent Semi-flush Mount Light Instruction Manual

Safety Instructions

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type B,Max 40W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture.

• Ladder

• Philips Head or Flat Blade Screwdriver

• Electrical Tape

• Pilers
  

• Wire Cutter/Stripper
  

PARTS TYPE & QTY INCLUDING

• (C) Mounting plate (1)
• (D) Green ground screw (1)
• (E) Hex nut (3)
• (F) Washer (3)
• (G) Stud (2)
• (H) Canopy (1)
• (I) Flat stent (3)
• (J) Nut (6)
• (K) Ring (2)
• (L) Bar (3)
• (M) Glass shade (3)
• (N) Stem (1)
• (O) Sockets assembly (1)

ACCESSORIES & QTY ENCLOSED:

• (A) Plastic wire connector (3)
• (B) Mounting screw (2)
• (J) Nut (Spare parts) (1)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Make pre-installation
   
   Step A1

   • Pass bars (L) through ring (K), then secure them with nuts (J).
   • Pass bars (L) through ring (K) and flat stents (I), then secure them with nuts (J).
     Step A2 » Pass flat stents (I) through canopy (H) and washers (F), then secure them with hex nuts (E).
     Step A3 » Screw stem (N) onto the top of sockets assembly (O).

3. Pass the fixture wires through canopy (H).

   • Screw stem (N) onto the bottom of canopy (H).
     

4. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.

5. Carefully pass the supply wires through mounting plate (C).

   • Secure mounting plate (C) to the outlet box with mounting screws (B).
     NOTE: the side of mounting plate (C) marked “GND” must face out.
     

6. Make wire connections
   Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
   Connect ground wires according to the below chart
   
   Connect wires according to the below chart
   ** Connect Black or Red Supply Wire to:| Connect White Supply Wire to:*
   ---|---
   Black| White
   Parallel cord (round & smooth)| *Parallel cord (square & ridged)
   Clear, Brown, Gold or Black without tracer| Clear, Brown, Gold or Black with tracer
   Insulated wire(other than green) with copper conductor| Insulated wire(other than green) with silver conductor

*Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

  * Twist wires together with plastic wire connectors until tightly joined.
  * Wrap each connector with approved electrical tape.
  * Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

7. Raise canopy (H) to the ceiling.

   • Secure canopy (H) in place by threading studs (G) into canopy (H) and mounting plate (C).
     

8. Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)

   • Carefully place glass shades (M) on the sockets as shown in the illustration.
     

9. Check everything is already installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

+1 850 296 2377
Working hours : Mon – Fri 9:00 – 16:00 EST
uolfin@newdecorworld.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>