HENG LONG 3810 63cm 2.4G RC Boat Paddle with Water Cooling Toy Instruction Manual
- June 6, 2024
- HENG LONG
Table of Contents
(Not suitable for children under 14 years old)
(Product Size)
(Length, : 580mm
Width1 210mm
Hight1 I 400mm
EIECTROMOTION POWERED RACIO
SPRAY pedan t
Warning
Choking hazard! This product contains small parts. NOT suitable for children under 3 years. Regularly check the battery charger wires, plugs and shell and other components for damage DO NOT use if any part is damaged. Replace any damaged components before reusing
(Caution proceeding)
-
Detachable small parts should be stored safely and out of reach of children.
-
If interference is experienced. turn the tank off and try it again in a different area.
-
Remote control will not function correctly if the batteries are low. Please replace the batteries.
-
Please discard old/used batteries in a safe manner. Consider your environment!
-
Please store the remote control in cool, dry place.
-
DO NOT expose to fire or high temperatures. moist storage.
-
Should the battery get wet, wipe immediately with a soft dry cloth.
-
Work boat body uses a set of 7.4V rechargeable batteries.
-
Remote control uses a 9V x1 battery.
-
Please pay attention to correct polarity when replacing batteries.
-
Rechargeable batteries should be charged under adult supervision.
-
DO NOT use a mix of old and new or different types of batteries.
-
Low. or exhausted batteries should be removed from the unit.
-
DO NOT short circuit any terminals. 8. DO NOT attempt to recharge non-rechargeable batteries.
-
Remove batteries from the unit when recharging.
-
DO NOT put batteries into a fire or into water.
-
The rated input voltage battery charger MUST be suitable for your mains power voltage
-
During charging it is quite normal for the charger and batteries to heat up.
Battery charging)
- Insert the USB cable into the USB socket of the computer or plug into the cell phone charger USB socket (as shown) At this time, the indicator of the USB cable red light is on
- Connect the battery plug with the USB charging plug according to the correct polarity as shown) At this time, the green light of the USB charging indicator starts flashing, This is the charging state About 4 hours later, the green charging indicator will turn on from flashing, the red light is off, charging is completed.
Warning
- Built-in battery intelligent protective board.
- This USB charging wire is special for 7.4V lithium batteries with a protective plate. It is forbidden to charge any other batteries, otherwise, it will cause danger and the company won’t bear the consequences.
- The rated input voltage battery charger with the home must be in line voltage.
- When charging, it is normal that the transformer and the battery may get mild heat.
- During the insertion or removal of the transformer, please pay attention that the finger should not be contacted to the end of the transformer.
- The plug connection. must recognize the positive and negative pole.
- If the battery connection is made the opposite, battery leakage or device malfunction may be caused
- Li-ion batteries after use, be sure to switch off or remove the Li-ion batteries from the work boat to prevent over discharge. otherwise, it will result in permanent damage to the Li-ion battery!
(Remote controller-Battery installation)
First use the screwdriver turns anti-clockwise, take out the screw. Then open
the battery cover
Remove the battery cover on the controller, place 1’9V battery into the
battery compartment with correct polarity
Close the battery cover, then use a screwdriver turn clockwise. lock the
screw.
(Model boat-Battery installation)
Open the battery cover with a”+” screwdriver turn anti-clockwise, take out the screw and turn the rotary switch as shown, then install the battery in.
Install the battery with the correct electrode.
Lock the screw and knob after you cover the battery.
(Self-assembly parts-installation)
PARTS LIST
2.4GIlz Instruction on decoding confirmation):
First turn on the remote controllers power, at the moment the indicator lamp
lights on. Then press and hold the”spray water” button, put the boat in the
water, the LED starts flashing(Start building connecting). After a while when
the LED lights are on without flashing, connecting succeed. After that the
boat becomes operational. When the boat moves out of controlling range (around
80 meters). The LED will flash slowly.
(7). Spray water: Press the “spray water button, the water cannon will spray out water on the top of the observation tower; Press the button one more time to stop spraying.
(Fine turning)
If the boat didn’t go straight when you press the trigger, you can open the fine turning cover to adjust with a screwdriver till it goes straight.
Caution:
When you adjust the fine turning switch to the end with the “-” screwdriver.
Stop turning at this time, Otherwise will damage the switch.
-
If the boat goes a little left side. You can turn to anti-clockwise direction lightly with the’-‘screw driver until it goes straight.
-
If the boat goes a little right side. You can turn to clockwise direction lightly with the–“screwdriver until it goes straight.
(To clean up the water in the rescue boat)
If the water goes into the boat by accident, please tilt the hull and open the stopper let the water goes out.
(Out of water functions)
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party
responsible for compliance could void the user s authority to operate the
equipment.
RF operating band: 2405-2475MHZ
Maximum transmitted power (EIRP): -5.87dBm (for EU Compliance)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>