kranzle K1505P Round Cleaner UFO Light Instruction Manual
- June 6, 2024
- kranzle
Table of Contents
kranzle K1505P Round Cleaner UFO Light
Round Cleaner UFO light
Operating pressure, max. | 160 bar |
---|---|
Flow rate, max. | 10 l/min |
nozzle system | 03 |
Temperature max. | 40 °C |
Weight | 1,25 kg |
Order no. | 41870 |
Safety notes
- Never touch the bottom of this appliance if it is connected and ready for operation! Never touch the rotating rotor!
- Never direct the high-pressure jet at people or animals! Never direct the high-pressure jet at yourself or other persons, not even to clean clothing or shoes.
- Never allow children or untrained persons to use the Round Cleaner INOX or to play with it! Children must be kept under supervision to prevent them from playing with the equipment.
Explanatory symbols used on the accessories
Read and observe safety instructions in the operating manual before use! There is a risk of injury from the rotating arm of the Round Cleaner light. Never reach under the Round Cleaner light when the high-pressure cleaner is running. After switching off the high-pressure cleaner, the rotating arm continues to rotate for a few seconds. After switching off the high-pressure cleaner, wait until the rotating arm stops and then unplug the high-pressure cleaner from the mains before working on the Round Cleaner light.
Assembly
- Pull out the clip with needle-nose pliers or alternatively lever out the clip with a screwdriver.
- Then insert the stainless steel tube from above and then reinsert the clamp. Inserting the clamp requires some force, as it must be firmly connected to both components to ensure a firm hold.
Application
Floor cleaning
The Round Cleaner is particularly suitable for cleaning plane surfaces like
carriage gateways, terraces etc. Mount the Round Cleaner instead of the spray
lance to the high-pressure gun of your HP-cleaner. Place the Round Cleaner to
a non-sensitive surface, e.g. asphalt. When cleaning sensitive surfaces try
out the Round Cleaner on a barely visible spot first and adjust the pressure
so that the surface is not damaged. Do not exceed the max. pressure (see
technical data)
Taking out of operation
- Switch off the high-pressure cleaner
- Cut off the water supply
- Open the trigger gun with safety catch briefly until the pressure is released
- Apply safety catch on the trigger gun
- Remove Kränzle Round Cleaner
- Check if the rotor is tangled with threads etc.
- Use a paper clip to check if the nozzles are clogged
Cleaning and care
Put the Round Cleaner onto the floor in such a way that the splash protection
brush cannot be deformed due to rough ground.
Small repairs – do it yourself
Problem
No water comes from the nozzle but the pressure gauge shows full pressure.
Cause
Most probably the nozzle is clogged.
- Straighten a paper clip.
- Clean the nozzle with the straightened paper clip. Rinse the high-pressure hose. And you can proceed with the high-pressure cleaning as before!
Warranty
Our warranty obligation is understood to exclusively cover material and manufacturing defects, wear is not covered by warranty. The machine is to be operated in conformity with this Operating manual. The operating manual is deemed to be part of the warranty provisions. This warranty shall only apply on the condition of proper use of original-Kränzle component parts and original-Kränzle replacement parts. With regard to legal warranty claims, the limitation periods of the respective countries shall apply. In the event of any warranty claims, please have your accessories and purchase voucher ready before contacting your local dealer or the nearest authorized customer service point, which you can also find in the internet under www.kraenzle.com. The machine is designed for private purposes only; no warranty shall be provided in case of industrial use. In case of any modifications on the safety installations or in case of exceeding the temperature and speed limit, any warranty claims shall become invalid – this shall also apply to the use of wastewater as well as any other faulty or inappropriate operation of the machine. Pressure gauge, nozzle, valves, sleeves, high-pressure hose, and spray equipment are wear parts and are not covered by the warranty obligation.