BRAYER BR1092 Electric Kettle Instruction Manual

: June 6, 2024
: BRAYER

Table of Contents

BRAYER BR1092 Electric Kettle
DESCRIPTION
SAFETY MEASURES AND OPERATION RECOMMENDATIONS
CLEANING AND MAINTENANCE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BRAYER BR1092 Electric Kettle

Thermopot is intended for boiling water and maintaining its temperature at a set level.
ATTENTION! For additional protection it is reasonable to install a residual current device (RCD) with nominal operation current not exceeding 30 mA into the mains. To install RCD, contact a specialist.

DESCRIPTION

BRAYER BR1092 Electric Kettle fig 2

Water level scale
Spout for pouring water
Control panel
Detachable lid
Lid opening button
Hand pump
Steam release openings
Hand pump mechanical lock
Carrying handle
Body
Power cord connector
Rotary base
Sealing gasket
Maximal water level mark «FULL»
Lid lock
Water boiling mode indicator «Boiling»
Keep warm mode indicators «Keep warm»
Reboil on button «Reboil»
Water dispense on button «Water dispense»
Power cord

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation instructions carefully before using the thermopot and keep it for future reference.

Use the thermopot for its intended purpose only, as it is stated in this manual.
Mishandling the thermopot can lead to its breakage and cause harm to the user or damage to his/her property and it is not covered by warranty.
The thermopot is intended for heating and boiling drinking water only, do not heat or boil any other liquids.
Make sure that operating voltage of the thermopot indicated on the label corresponds to your home mains voltage.
The power plug is equipped with a grounding contact, plug it into the socket with
reliable grounding contact. In case of short circuit the grounding reduces the risk of electric shock.
Contact an electrical technician, if you are not sure that your sockets are installed properly and grounded.
To prevent fire do not use adapters designed for connecting the plug to the mains socket without grounding contact.
In case of sparking in the mains socket and occurrence of smell of burning, unplug the unit and apply to the organization maintaining your home mains.
If smoke appears from the body of the thermopot, unplug the unit and take measures to prevent fire spreading.
Do not use the thermopot outdoors.
It is not recommended to use the unit during lightning storms.
Protect the unit from impacts, falling, vibrations and other mechanical stress.
Do not switch the thermopot on if the water tank is empty.
Do not fill the thermopot with water directly from the faucet; to fill the thermopot use a suitable bowl.
Do not place the thermopot next to the walls or close to the kitchen furniture.
Place the thermopot keeping at least 20 cm gap between the thermopot body and the wall and at least 50 cm gap above the thermopot.
Never leave the plugged-in thermopot unattended.
Do not use the thermopot in proximity to kitchen sink, in bathrooms, near swimming pools or other containers filled with water.
Do not use the thermopot near heating appliances, heat sources or open flame.
Do not use the thermopot in places where aerosols are used or sprayed, and in proximity to inflammable liquids.
Place the thermopot on a flat stable surface; do not place it on the edge of a table. Do not let the power cord hang from the edge of the table and make sure it does not touch hot surfaces or sharp edges of furniture.
Do not touch the power cord and the power plug with wet hands.Do not switch the thermopot on without water, after the thermopot is filled, close the lid tightly.
Ensure that the water level is not above the maximal mark «FULL». If the water level exceeds the maximal mark, boiling water can splash out of the thermopot during boiling.
To avoid burns by hot steam, do not bend over the steam release openings in the thermopot lid. Do not block the steam release openings with any objects.
Do not open the thermopot lid while water boiling.
Be careful while carrying the thermopot filled with boiling water.
Be very careful when pouring hot water out of the thermopot.
Unplug the thermopot before cleaning or when you are not using it. When unplugging the thermopot hold only the power cord plug and carefully remove it from the mains socket, do not pull the power cord — this can lead to damage of the power cord or the socket or cause short circuit.
To avoid electric shock do not immerse the thermopot into water or any other liquids.
Do not wash the thermopot in a dishwashing machine.
For children safety reasons do not leave polyethylene bags, used as a packaging, unattended.
ATTENTION! Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!
The thermopot is not intended for usage by children.
Do not leave children unattended to prevent using the unit as a toy.
Do not allow children to touch the unit and the power cord during the thermopot operation.
Place the unit out of reach of children during the operation and cooling down.
This unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
Check the integrity of the power cord, the power plug and the thermopot body periodically.
If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.
If the power cord is damaged, it should be replaced with a power cord received from the manufacture or service.
Transport the thermopot in the original package.
Keep the unit out of reach of children and disabled persons.

THERMOPOT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE COFFEE MAKER FOR COMMERCIAL OR LABORATORY PURPOSES. BEFORE USING THE THERMOPOT

After unit transportation or storage at low temperature keep it for at least 3 hours at room temperature before switching on.

Unpack the thermopot and remove all the packaging materials.
Keep the original package.
Read the safety measures and operating recommendations.
Check the delivery set.
Examine the thermopot for damages, in case of damage do not plug it into the mains.
Make sure that the specifications of power supply voltage specified on the label correspond to the specifications of your mains. When using the thermopot in the mains with 60 Hz frequency, the unit does not need any additional measures.
Wipe the outer surface of the unit body (10) with a clean, slightly damp cloth to remove dust.
Open the lid (4) by pressing the button (5) and holding it (pic. 1).
Wipe the inner surface of the thermopot flask with a clean, slightly damp cloth to remove dust. Close the lid (4).

SWITCHING THE THERMOPOT FOR THE FIRST TIME AND USING THE UNIT

Place the thermopot on a dry flat surface keeping at least 20 cm gap between the thermopot body and the wall or furniture and at least 50 cm gap above the thermopot.
Open the lid (5) by pressing the button (5) and holding it (pic. 1).
Fill the thermopot with water using a suitable bowl, do not exceed the maximal water level mark (14) «FULL» (pic. 2). Do not fill the thermopot with water directly from the faucet; to fill the thermopot use a suitable bowl.
Notes : to reduce the mineral deposit (scale), we recommend using the water cleaned with domestic filters.
Close the lid (5) until the lock clicking, make sure that the lid (5) is closed.
Notes : when using the thermopot, always check the sealing gasket (13). If you find any cracks on the sealing gasket (13), stop using the thermopot and apply to the service center to replace the gasket (13).
Insert the power cord (20) jack into the connector (11) on the thermopot body, and the power cord (20) plug into the mains socket.
The boiling mode indicator «Boiling» (16) will light up on the control panel (3) and the keep warm indicator (17) «Keep warm» will light up.
After long water boiling the thermopot will switch to the keep warm mode, the indicator (16) «Boiling» will go out and the keep warm mode indicator (17) «Keep warm» will glow constantly.
Notes : the thermopot uses a long boiling technology which significantly reduces the chlorine level in water.
To avoid burns by hot steam, do not bend over the steam release openings (7) in the thermopot lid (4). Do not block the steam release openings (7) with any objects.
Drain the water after the first boiling. Hot water resulting from the first boiling is not recommended to consume, you may use it for domestic needs.

ATTENTION! Be careful when pouring out water to avoid burns by hot water.

To drain the water you can do the following: First option: place a suitable bowl, for instance, a cup under the spout for pouring water (2) and press
the water dispense button with a rim of the cup (pic. 3). Second option: place a suitable bowl under the spout for pouring water (2) and press the water dispense button (19) «Water dispense» (pic. 4).

Third option:

in case of power cut use the hand pump (6);
remove the hand pump lock by setting the block (8) to the position « »;
place a suitable bowl under the spout for pouring water (2);
press the hand pump (6), the water will be pouring from the spout (2);
after you finish pouring water, set the block (8) to the position « » (pic. 5).
To switch the thermopot off disconnect the power cord (20) plug from the mains socket.
Open the thermopot lid (4) and wait until it cools down completely.
Always drain the remaining water from the thermopot flask, to do this remove the lid (4).
Before removing the lid (4) open it, press on the lock (15) above, take the button (5) and remove the lid (4) by pulling it towards the control panel (3) (pic. 6).
Carefully tilt the thermopot to drain the remaining water (pic. 7).
Install the lid (4) back to its place. To do this, set the lid (4) at a small angle, press the lock (15) and insert the lid (4) to its installation place. Release the lock (15). Before using the thermopot make sure that the lid (8) is fixed properly with the lock (15).

Additional information

The thermopot is equipped with rotating base (12). You can turn the thermopot body (10) in the required direction.
Check the water level in the thermopot using the scale (1).
Timely refill the thermopot.
If the water temperature goes significantly below the preset temperature (for example, if you added cold water), the boiling mode will switch on and the indicator (16) «Boiling» will light up.
You can switch the reboiling mode on by pressing the button (18) «Reboiling», the indicator (16) «Boiling» will light up. After boiling the water the indicator (16) «Boiling» will go out and the keep warm mode will switch on.

CLEANING AND MAINTENANCE

Before cleaning the thermopot unplug it, open the lid (4) and wait until the thermopot cools down completely.
Always drain the remaining water from the thermopot flask, to do this remove the lid (4).
Before removing the lid (4) open it, press on the lock (15) above, take the button (5) and remove the lid (4) by pulling it towards the control panel (3) (pic. 6).
Carefully tilt the thermopot to drain the remaining water (pic. 7).
Install the lid (4) back to its place. To do this, set the lid (4) at a small angle, press the lock (15) and insert the lid (4) to its installation place. Release the lock (15). Before using the thermopot make sure that the lid (8) is fixed properly with the lock (15).
Clean the outer surface of the thermopot body (10) with a slightly damp cloth and then wipe it dry.
Use neutral detergents to remove dirt, do not use metal brushes, abrasives and solvents.
Do not immerse the thermopot and the power cord (20) into water or other liquids.
Do not put the thermopot in a dishwashing machine.

Stains on the inner surface of the thermopot flask

Water contains various minerals that can cause stains on the inner surface of the thermopot flask, the stains do not affect the operation of the thermopot, stains are not covered by the warranty.
You can remove the stains from the inner surface of the thermopot flask with citric acid solution or table vinegar.
To remove the flavour of citric acid or vinegar, boil water and pour it out.
Repeat this procedure until the smell and foreign taste vanish completely.

Removing the mineral deposits (descaling)

Scale, appearing inside the thermopot flask, influences the water taste and disturbs the heat exchange between water and the heating element. It also risks damaging the heating element. Burning of the heating element caused by the large amount of scale in the thermopot flask is not covered by warranty.
To remove the scale fill the thermopot with a mixture of one part ordinary vinegar and two parts water up to the maximal level mark (15) «FULL».
Insert the power cord (20) jack into the connector (11) on the thermopot body, and the power cord (20) plug into the mains socket.
The thermopot will be switched on in the boiling mode. After the water boiling disconnect the power cord (20) plug from the socket and leave the thermopot filled with the vinegar solution overnight.
In the morning pour out the vinegar solution, fill the thermopot with water up to the maximal level «FULL», boil it and pour out the water.
You can use special descaling agents for
electric kettles, strictly following the instruction.
Clean the thermopot from scale regularly.

STORAGE

Before taking the thermopot away for long storage, disconnect it from the mains, let the unit cool down and pour out the water.
Clean the thermopot.
Keep the thermopot out of reach of children and disabled persons.

DELIVERY SET

Thermopot – 1 pc.
Power cord – 1 pc.
Manual – 1 pc.

TECHNICAL SPECIFICATIONS

Power supply 220-240 V, ~ 50-60 Hz
Rated input power: 900 W
Max capacity: 4 l

RECYCLING

To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, take the unit and the batteries to specialized stations for further recycling. The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner. For further information about recycling of this product apply to a local municipal administration, a household waste disposal service or to the shop where you purchased this product. The manufacturer reserves the right to change the design, structure and specifications not affecting general operation principles of the unit, without prior notice.

The unit operating life is 3 years
The manufacturing date is specified in the serial number. In case of any malfunctions, it is necessary to apply promptly to the authorized service center.