WARING COMMERCIAL WIH400 Commercial Induction Range Instruction Manual
- June 6, 2024
- WARING COMMERCIAL
Table of Contents
COMMERCIAL INDUCTION RANGE
WIH400, WIH400B
For your safety and continued enjoyment of this product, always read the instruction book carefully before using it.
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed, including the following:
- READ ALL INSTRUCTIONS.
- Unplug from outlet when not in use, before putting on or taking off parts and before cleaning.
- To protect against the risk of electric shock, do not put the appliance in water or other liquids.
- Do not touch surfaces that may be hot.
- Avoid contact with moving parts.
- Do not operate the Waring ™ Commercial Induction Range or any other electrical equipment with a damaged cord or plug, or after the unit malfunctions or is dropped or damaged in any manner. Return it to the nearest Waring Authorized Service Center for examination, repair, and/or adjustment.
- The use of attachments not recommended or sold by Waring may cause fire, electric shock, or injury.
- Do not use outdoors.
- Do not let the cord hang over the edge of the table or counter, or touch hot surfaces.
- The Waring™ Commercial Induction Range should always be on a stable countertop or table.
- Do not use appliances other than intended use.
- T his appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Do not cook on a broken cooktop – If the glass cooktop should break, cleaning solutions and spillovers may penetrate the broken surface and create a risk of electrical shock.
- Clean cooktop with caution – If a wet sponge or cloth is used to wipe spills on a hot cooking area, be careful to avoid steam burn; some cleaners can produce noxious fumes if applied to a hot surface.
- Do not place metal objects such as knives, forks, spoons and lids on the glass surface since they can get hot.
SAVE THESE INSTRUCTIONS APPROVED FOR COMMERCIAL USE
GROUNDING INSTRUCTIONS:
- For your protection, the Waring™ Commercial Induction Range is equipped with a 3-conductor cord set.
- 120-volt units are supplied with a molded 3-prong grounding-type plug and should be used in combination with a properly connected grounding-type outlet, as shown in Figure
- If a grounding-type outlet is not available, an adapter, shown in Figure 2, may be obtained to enable a 2-slot wall outlet to be used with a 3-prong plug.
As shown in Figure 3, the adapter must be grounded by attaching its grounding lug under the screw of the outlet cover plate.
CAUTION: Before using an adapter, it must be determined that the outlet
cover plate screw is properly grounded. If in doubt, consult a licensed
electrician. Never use an adapter unless you are sure it is properly grounded.
NOTE: Use of an adapter is not permitted in Canada.
SPECIAL CORD SET INSTRUCTIONS
A short power-supply cord is provided to reduce the risks resulting from
becoming entangled in or tripping over a longer cord.
Extension cords may be used if care is exercised in their use.
If an extension cord is used, the marked electrical rating of the extension
cord must be at least as great as the electrical rating of the appliance. If
the appliance is of the grounded type, the extension cord should be a
grounding-type 3-wire cord, and the longer cord should be arranged so that it
will not drape over the countertop or tabletop where it can be pulled by
children or tripped over.
PARTS
- Heat Mode Setting
- Temperature Mode Setting
- Timer Mode Setting
- LCD Display
- An adjustment Control for Temperature/Heat/Timer
- On/Off Power Button
- Stainless Steel Housing
- Schott® * Ceramic Glass Cooking Surface
SPECIFICATIONS
MODEL
| ELECTRICAL| PLUG TYPE| DIMENSIONS (inches)|
LISTING
---|---|---|---|---
WIH400| 120V, 15 AMP 1800 W| NEMA 5-15 P| 16.5″ (D) x 4″ (H)| ETLUS NSF
WIH400B| 208/240V, 12 AMP 2900/3300 W| NEMA 6-20 P| **** 16.5” (D) x 4” (H)|
TELUS NSF
NOTE: Your Waring™ Commercial Induction Range defaults to the Fahrenheit
setting.
Every time the unit is plugged in it will default to Fahrenheit.
To change to Celsius follow the directions on page 5.
- Schott is a trademark of the Schott Corporation.
OPERATION
NOTE: The Induction Range requires induction-ready cookware. If the pan is not induction ready, it will not register on the induction range. The LCD display will show “—–” and “STANDBY” will flash (as seen in figure 1) when attempting to select a heat mode without an induction-ready pan on the glass cooking surface. The unit will automatically shut off after 60 seconds of not having an induction-ready pot/pan.
-
Before turning on the power, make sure the cookware is on the ceramic cooking surface. Your Waring™ Commercial Induction Range is equipped with small-object detection which will prevent it from operating unless you have an appropriate sized induction-ready pan in place.
-
To turn the power on, press the ON/OFF button and choose a cooking mode by pressing the HEAT or TEMP button.
NOTE: The unit will automatically shut off after 30 seconds if you do not choose a cooking mode.
a) The HEAT button allows you to choose how many watts of power to cook with.
b) The TEMP button allows you to choose the temperature at which you cook. -
Once you’ve chosen a cooking mode, use the + and – buttons to set the desired wattage or temperature.
EMPTY-PAN DETECTION
After extended periods of time with an empty pan, your Waring ™ commercial Induction Range will automatically shut off.
CHOOSING FAHRENHEIT OR CELSIUS
In TEMP mode, you can choose Fahrenheit or Celsius. When the unit is plugged
in and in the OFF position the LCD screen will be blank. Press and hold the
TEMP button for
three seconds. The screen will illuminate and display °C and °F, as seen in
figure 2. The current setting will blink. Use the + and – buttons to switch to
your desired setting. Once you’re desired to set is blinking, press the TEMP
button to confirm and then press the ON/OFF button.
NOTE: The induction burner automatically defaults to Fahrenheit once
unplugged.
SETTING THE TIMER
-
Turn the unit on and choose your cooking mode by pressing TEMP or HEAT.
-
Press the TIMER button and use the + and – buttons to adjust time anywhere from 1 minute to 10 hours. Once the timer display stops blinking, the timer will begin to
count down. NOTE: It will count down seconds when it reaches:59 seconds. -
When the time has counted down to “0” the unit will beep
-
times and the screen will blink. WARNING: The unit will not automatically shut off.
INDUCTION-READY POTS AND PANS
To use the Waring™ Commercial Induction Range, your pot or pan must have a flat bottom surface of 4.75 inches to 10 inches in diameter and be marked suitable for induction cooking.
SAFETY
CAUTION: UNPLUG FROM OUTLET WHEN NOT IN USE!
Please note that the unit will still be too hot to handle immediately after
use. The Waring ™ Commercial Induction Range has a thermal cutoff safety
device to avoid overheating. If the Induction Range shuts off automatically,
unplug it and allow it to cool for 20 minutes.
Plug back in and continue use.
CLEANING AND MAINTENANCE
Always unplug the unit after each use and before cleaning. Unplug the unit
when not in operation. The Waring™ Commercial The induction Range should be
cleaned after each use with warm soapy water. The exterior of the unit may be
cleaned by carefully wiping with a damp cloth.
Clean the cooking surface while the unit is warm, using warm soapy water. DO
NOT USE COLD WATER ON WARM SURFACES.
Do not immerse completely in water to clean. The appliance is not to be
cleaned with a water jet.
NOTE: The cooking surface will be hot after use. Use caution when
handling cooking utensils and cookware.
Any other servicing should be performed by an authorized service
representative.
TROUBLESHOOTING
Error Code List on LCD Display
Error Code| Description of Error|
Solutions
---|---|---
“—- ” and the unit beeps| There is no cookware, empty cookware or
suitable cookware on the range. The power will completely shut off within 60
seconds if there is no cookware or the wrong type of cookware on the unit.| •
Make sure your pot/pan is induction ready.
• Check the diameter of the pot/pan; it must have a flat bottom between 4.75″
and 10″ in diameter.
E1| Voltage is under 78V.| Check electrical specifications of power
source.
E2| Voltage is over 145V.
E3, E5| The heater is damaged.| Contact the nearest authorized service
facility for troubleshooting, repair and adjustment.
E6| The thermal protection has shut the unit off due to overheating in
the TEMP mode.| Unplug the unit and let cool for 20 minutes. Plug the unit
back in and continue use.
NOTE: When cooking in HEAT mode, the maximum temperature is 300˚F. To cook at temperatures between 300˚F – 500˚F, use HEAT mode.
E7| The temperature inside the unit is too hot.| Unplug the unit and let
cool for 20 minutes. Once the unit is completely cooled, be sure it is
positioned away from the wall and that there are no obstructions to the
airflow. Plug the unit back in and continue use.
E9| NTC (Overheat Protection Sensor) has been activated or triggered.|
Unplug the unit and let it cool for 20 minutes. Plug the unit back in and
continue use.
Trademarks or service marks of third parties used herein are the trademarks or service marks of their respective owners.
©2016 Waring Commercial
314 Ella T. Grasso Ave.
Torrington, CT 06790
waringcommercialproducts.com
Printed in China
WIH400 IB
15WC018849
IB-11918A
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>