poly Blackwire 3300 Series User Guide
- June 6, 2024
- Poly
Table of Contents
PLANTRONICS + POLYCOM. NOW TOGETHER AS
Blackwire 3300 Series
User Guide
Overview
Standard LEDs
| Icons | Inline control | LEDs | What they mean |
|---|---|---|---|
| Call button | Flashing green | Incoming call | |
| Solid green | On a call | ||
| Slow flashing green | Call on hold | ||
| Volume up button | Increases the listening volume | ||
| Volume down button | Decreases the listening volume | ||
| Mute button | Solid red | Headset muted |
**Microsoft Teams LEDs***
| Icons | Inline control | LEDs | What they mean |
|---|---|---|---|
| Call button | Solid purple | Headset connected; Microsoft Teams |
connected
| | Flashing purple x3| Microsoft Teams failed to connect
| | Flashing blue| Incoming call
| | Solid blue| On a call
| | Slow flash blue| Call on hold
| | Pulsing purple| Microsoft Teams notification
| Volume up button| | Increases the listening volume
| Volume down button| | Decreases the listening volume
| Mute button| Solid red| Headset muted
**NOTE *** Requires Microsoft Teams variant and application
Setup and software
Power and setup
Power on your headset by connecting to your computer or mobile device.
• USB-A/USB-C connector
• 3.5 mm connector (Blackwire 3315/3325 only)
NOTE Headset call control functionality is not available.
Load software
Some softphones require the installation of Plantronics Hub for Windows/Mac to
enable headset call control (answer/end and mute) functionality.
Download Plantronics Hub for Windows/Mac by visiting poly.com/software.
Manage your headset settings on your computer with Plantronics Hub:
- Call control for softphones
- Change headset language
- Update firmware
- Turn features on/off
Fit
Adjust the headband
Lengthen or shorten the band until it fits comfortably. The cushions should
sit comfortably over the center of your ears.
Position the boom
This headset can be worn on the left or right side. Rotate the boom to align with your mouth.
CAUTION To avoid breaking the boom, only rotate it up and over 180°.
Adjust the boom
Gently bend the boom in or out so it is approximately two finger widths from the corner of your mouth.
Basics
Make/take/end calls
Headset call control is a software feature and dependent on a compatible softphone. If you have not installed Plantronics Hub or do not have a compatible softphone, press the headset call button first and then make/take/end the call using the softphone application. Download Plantronics Hub for Windows or Mac at poly.com/software.
Answer or end a call
Tap the Call button or use your softphone.
Make a call
Dial using your softphone application.
Redial
When not on an active call, double-tap the call button to redial the last
call.
Hold
To put a call on hold, press and hold the Call button until you hear a beep or
voice prompt.
Volume
Listening volume
Press the Volume up (+) or Volume down (-) button.
Adjust headset microphone volume (softphone)
Place a test softphone call and adjust softphone volume and PC sound volume
accord
Mute
During a call, briefly press the mute button to mute the microphone on the inline controller. To unmute press the button again.
Troubleshooting
Headset
I hear a high-pitched noise when wearing the headset.| Ensure that your 3.5 mm
connector is fully connected to the headset controller.
---|---
I cannot hear caller.| Listening volume is too low. Press the volume up button
on the headset. and/or ensure that the volume setting on your computer is set
accurately.
Your headset is not set as the default audio device. Use the audio settings in
your sound control panel/preferences to select your headset as the default
audio device.
Ensure that your 3.5 mm connector is fully connected to the headset
controller.
Callers cannot hear me.| Headset is muted. Tap the mute button to unmute the
microphone.
Headset microphone boom aligned incorrectly. Align the headset boom with your
mouth.
Your headset is not set as the default Voice device. Use the audio settings in
your sound control panel/preferences to change the input device.
Ensure that your 3.5 mm connector is fully connected to the headset
controller.
The sound in the headset is distorted.
I can hear an echo in the headset| Lower the listen volume on your softphone
until the distortion disappears.
Adjust volume on headset.
Ensure that your 3.5 mm connector is fully connected to the headset
controller.
When I use my headset with a softphone, the headset call control and mute
buttons don’t work.| Make sure the softphone you are using is supported by
viewing
www.plantronics.com/softphonecompatibility.
If required to enable headset control (answer/end and mute) functionality,
ensure you have Plantronics Hub for Windows/Mac installed. See Load software.
Your mobile device may not support call control functionality. Check with
device manufacturer.
The other headset I was using to listen to music does not work any more.| Your
headset will set itself as the default audio device in Windows. Use the audio
settings in your sound control panel/preferences to change the audio device.
My phone is not finding my headset during a call or while listening to music.|
When on a call or listening to music, make sure that audio is routing to the
desired headset by going to your settings and ensuring it is defaulted.
Support
NEED MORE HELP?
poly.com/support
Plantronics, Inc.
345 Encinal Street
Santa Cruz, CA 95060
United States| Plantronics B.V.
Scorpius 171
2132 LR Hoofddorp
Netherlands
---|---
©
2020 Plantronics, Inc. All rights reserved. Poly, the propeller design, and
the Poly logo are trademarks of Plantronics, Inc. Bluetooth is a registered
trademark of Bluetooth SIG, Inc. and any use by Plantronics, Inc. is under
license. All other trademarks are the property of their respective owners.
Manufactured by Plantronics, Inc.
215239-06 05.20
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>