hama 00176588 WLAN LED Built-In Spotlight Instruction Manual

: June 6, 2024
: Hama

Table of Contents

WiFi LED-Downlight
Operating instruction
Explanation of symbols used on the product label
Explanation of warning symbols and notes
Package contents
Safety instructions
- Removal
Getting started
Care and Maintenance
Warranty Disclaimer
Recycling Information Note on environmental protection:
RF exposure information
Declaration of Conformity
Technical data
Service & Support
Documents / Resources

hama 00176588 WLAN LED Built-In Spotlight

WiFi LED-Downlight

Step 1: cut the hole on ceiling

Step 2: connect power (AC 220 – 240V)

Step 3: Vertically put the spring buckle and then release on the hole of ceiling

Step 4: Finish installation

Operating instruction

| Important information – Quick-reference guide:

This quick-reference guide contains the most important basic information, such as safety instructions and the steps necessary to operate the product.
The full text of the manual is available at the following internet address:
www.hama.com -> 00176578/79/88/89 -> Downloads
Save the manual on your computer for reference and print them out if possible.

---|---

Explanation of symbols used on the product label

| Electrical device of safety class II.
Protection against electric shock thanks to reinforced or double insulation of live parts.
---|---
| The product is intended only for use inside buildings.
| Only use in a dry environment.
| No heat-insulating materials must be in contact with the light.
| The product must only be used with alternating current.
| Non-dimmable. The lamp is not suitable for use with a conventional dimmer.
| The article may only be connected by a qualified electrician who complies with national regulations and those of the local energy supply company, and who has sufficient knowledge regarding installation locations, fire protection and electrical installation work.

Explanation of warning symbols and notes

| Risk of electric shock
This symbol indicates a risk of electric shock from touching product parts carrying hazardous voltage.
---|---
| Warning
This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.
---|---
| Note
This symbol is used to indicate additional information or important notes.
---|---

Package contents

Package contents for 176578 and 176588:
1 WiFi built-in spotlight
1 quick-start guide
Package contents for 176579 and 176589
3 WiFi built-in spotlight
1 quick-start guide

Safety instructions

This product is intended for private, non-
commercial use only.
This product is intended exclusively for installation
in suspended ceilings or suitable built-in recesses or concrete built-in housings.
Use the product only for the intended purpose.
Do not drop the product and do not expose it to any major shocks.
Do not operate the product outside the power limits specified in the technical data.
Do not modify the product in any way. Doing so voids the warranty. · Children must not play with the device. Cleaning and user maintenance must not be carried out by children without supervision.
As with all electrical products, this device should be kept out of the reach of children.
Dispose of packaging material immediately in accordance with the locally applicable regulations.
The product should only be installed in selfcontained rooms. It is not suitable for installation in bathrooms.
The product must only be operated on a supply network as described on the type plate.
Before mounting, check that the ceiling you have chosen is suitable for the weight to be mounted. Also make sure that there are no electric, water, gas or other lines running through the ceiling at the mounting site.
Electrical cables must never become trapped or twisted between the product and the surface.
If the product is attached to a metal surface, it must be connected to an earth lead or the installation’s potential equalising cable.
These built-in lights are not compatible with dimmer switches, motion sensors or dimmers.
Protect the product from dirt, moisture and overheating and use it in dry rooms only.
Only use the article under moderate climatic conditions.
Do not use the product in areas in which electronic products are not permitted.
Do not use the product in a damp environment and avoid splashing water.
Do not bend or crush the cable.
Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
Do not continue to operate the device if it is visibly damaged

| Risk of electric shock
Do not open the product and do not operate it if it is damaged, if smoke, a strange smell or loud noises are coming from it. Immediately contact your dealer or our service department (see item “Service and Support”).
---|---
| Note
The light source of this light is not replaceable; when the light source has reached the end of its life, you need to replace the entire light.
---|---
| Warning
Never look straight into the light source and do not aim its beam of light straight into the eyes of other people or animals. This could damage your/their eyes.
---|---

Example installation in wood / drywall ceiling:

Before commencing any installation, maintenance or repair work, please disconnect the power circuit by disconnecting the fuse.
Secure the power circuit against being switched back on.
Check that the minimum installation depth of 80 mm (47 mm light + 33 mm clearance) is available. The clearance between the upper edge of the light and the ceiling must not be less than 33 mm to allow ventilation.
The minimum distance between the lights and flammable materials must be no less than 50 cm. Do not cover the light with any heatinsulating material
Mark out the position where the light is to be installed.
Create an installation opening with a diameter of 75 mm using a suitable hole saw. Take care not to disturb any hidden installation or supply lines.
The terminal points (e.g. terminal strip) between the domestic installation and the built-in spotlight connection cable must be clamped in suitable junction boxes. (Not included in the extent of delivery).
Continuing cables to the next built-in light must correspond in terms of structure and insulation to the operating mode. The yellow / green (earth / PE conductor) cable is not connected. Other lights are cabled in parallel.
230 V 50 Hz
Close the junction box and push it into the installation opening. Also ensure that the cables are free of compressive and tensile forces. Protect all cables and insulation from any potential damage.
Position the built-in light at an angle and first insert a clamp into the installation opening. The springs on the clamp are very powerful and can cause injury if due attention is not paid!
Now guide the second clamp into the installation opening. The built-in light is now slowly introduced all the way into the installation opening. The force of the clamps is sufficient to hold the built-in light in position.
No further fixings are needed. For precise alignment, the built-in light can be easily repositioned and rotated. The internal part of the light can also be swivelled.
Only reinsert the fuse once all built-in lights have been installed.

Removal

Pull the built-in light out of the installation opening on one side. Take care to ensure that the clamp does not accidentally slip out of the opening. Otherwise there is a danger that fingers may become trapped.
First carefully remove one clamp, then the other, from the installation opening.
The further removal process is carried out in the reverse order to the installation process.

Getting started

Download the Hama Smart Solution app from the Apple App Store or on Google Play.
Open the Hama Smart Solution APP
The first time you use the app, you need to register and create a new account. If you already have an account, log in with your access details
The LED built-in spotlight starts to flash quickly (if it does not, switch the LED built-in spotlight ON and OFF again quickly 3 times)
Now click the + at the top right-hand corner and select Lighting, then your device.
Confirm that the LED built-in spotlight is flashing quickly.
Now enter the name of your WiFi network and the password and confirm.
The LED built-in spotlight is now connected. Once the connection is successful, the LED built-in spotlight will stop flashing
You can now set up, control and configure the WiFi Smart LED built-in spotlight with the APP

Care and Maintenance

| Note
Disconnect the product from the mains before cleaning and during prolonged periods of non-use.
---|---

Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.
Ensure that no water is able to enter the product.

Warranty Disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

Recycling Information Note on environmental protection:

After the implementation of the European Directive 2012/19/EU and 2006/66/EU in the national legal system, the following applies: Electric and electronic devices as well as batteries must not be disposed of with household waste. Consumers are obliged by law to return electrical and electronic devices as well as batteries at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilising old devices/Batteries, you are making an important contribution to protecting our environment.

RF exposure information

This device complies with the EU requirements for limiting the exposure of the general public to electromagnetic fields by means of health protection. The device complies with RF specifications provided it is used 20 cm away from the body.

Declaration of Conformity

Hereby, Hama GmbH & Co KG declares that the radio equipment type [00176578, 00176579, 00176588, 00176589] is in compliance with Directive 2014/53/ EU. The full text of the EU declaration of conformity is available at the following internet address: www.hama.com -> 00176578, 00176579, 00176588, 00176589 -> Downloads.

Technical data

Input voltage	220 V–240 V, 50 Hz
Frequency band	2.4 GHz
Maximum radio-frequency power transmitted	< 100 mW
Lamp Current	45 mA
Nominal power consumption	5 W
Net luminous flux	350 lm
Colour temperature	2700-6500K CCT, CRI80
Protection class	II
Protection	IP 20; installation only in dry areas
Diameter	External: 90mm; Installation dimensions: 75mm
Installation depth	47mm
Life	25,000h
Switching cycles	15,000 x
Beam angle	120°
Can be dimmed	Only via the app