SALUS KL06 24V Wiring centre (6 zones) 24V User Manual

X 2020 [ENG]
Wiring centre (6 zones) 24V Model: KL06 24V
Ver. 1 Issued: X 2020
Power supply: 24V

Wiring centre description

1. Cartridge fuse 5 x 20 mm 2 A

2. Power Supply

3. Diodes

4. NSB (Night Set Back reduction) function

5. Thermostats connection

6. Actuators connection

7. A. PL06 – pump (or boiler) control module
   7B. PL07 – pump and boiler control module

8. Serial connector for PL06 and PL07 modules

Introduction

Wired KL06 24V wiring centre allows easy and quick connection of thermostats and actuators. It has a serial connector for additional modules (sold separately):

• PL06 Pump or boiler control module
• PL07 Pump and boiler control module The KL06 24V wiring centre is adapted to work with NC type actuators (normally closed) and maximum 6 thermostats.

Product Compliance

This product complies with the essential requirements and other relevant provisions of the following EU Directives: EMC 2014/30/EU, Low Voltage Directive LVD 2014/35/EU, RoHS directive 2011/65/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.saluslegal.com

Safety information

Use in accordance with national and EU regulations. Use the device as intended, keeping it in dry condition. Product for indoor use only. Installation must be carried out by a qualified person in accordance with national and EU regulations.
Before any operations related to the power supply (connecting wires, installing the device, etc.), make sure that KL06 is not connected to any power source. Installation must be carried out by a qualified person. Incorrect connection of the wires may cause damage to the wiring centre. The KL06 can not be used in conditions of water vapour condensation or exposure to water.

Technical Information

1. Fuse
   Note: Replace the fuse only when the wiring centre is disconnected from power supply 24V~. The main fuse is located under the housing cover next to power supply terminals and secures the wiring centre and the devices connected to it. Use cartridge fuses (5×20 mm) with nominal max current 2 A. To replace fuse remove the fuse holder with a flat screwdriver and pull out the fuse.

2. Power Supply
   The power supply for the wiring centre is 24V 50Hz 230 V AC

3. LED diodes
   – green LED diode indicates power supply connection 230 V.
   – orange LED diode indicates NSB function being activated.

4. NSB (Night Set Back reduction) function
   NSB function is activated in non-programmable Salus thermostats of the Expert NSB, HTR, BTR series via external signal. NSB 24 V signal (night-time temperature reduction) is sent via an external timer or programmable thermostat connected to the KL06 wiring centre. Non-programmable thermostats are receiving NSB signal and reducing setpoint temperature (by switching to eco-mode). All thermostats have to be connected using a 4-wire cable (min. 4 x 0,75 mm², max. 4 x 1,5 mm² ).

5. Thermostats connection
   · Connecting HTR series thermostat with NSB function

Connecting RT10 24V thermostat with NSB function.

Connecting ON/OFF battery-powered thermostat with voltage-free COM / NO output contacts (np. 091FL, RT310, RT510).

Note: In NSB, HTR, ERT, BTR product series follow interchangeable signifying: = SL = NSB

Actuators connection

Wires of thermoelectric actuators should be plugged into self-locking connectors in appropriate zones. 4 actuators can be connected directly to one zone.

Note: There is a voltage of 24V AC on the actuator contacts during their operation.
Example based on T30NC 24 V actuators.
7 A. PL06 ­ pump (or boiler) control module
PL06 module is used to control the pump (or boiler) using volt-free NC/COM/NO contacts. When any of the thermostats connected to the KL06 24 V reports heat demand, COM/NO contacts are closing. COM/NO contacts are opening, when thermostats connected to the wiring centre will stop sending signals for heating.
Jumpers 0-15 **These are used to set in minutes the delay time (overrun time). The default setting is,,0″.
0-15 values specify the time in minutes. E.g. when the jumper is set to a value,,0″, COM/NO output will turn off as soon as the thermostats stop calling for heat. If the jumper will be set to the value,,10″, the module will turn off 10 min after the thermostats stop calling for heat.
Jumpers P,1,2,3,4,5,6
They are used to select the zone which turns on the module. The default setting is,,P”.
P – all zones start the module
1, 2, 3, 4, 5, 6 ­** select the specific zone which turns on the module.

PUMP CONTROL BOILER CONTROL

7 B. PL07 – pump and boiler control module
PL07 module is used to control the pump and the boiler using volt-free COM/NO contacts. When any of thermostats connected to the KL06 230V reports heat demand, COM/NO contacts are closing.COM/NO contacts are opening, when thermostats connected to the wiring centre will stop sending a signal for heating.
ON-OFF Delay jumper
Is used to activate the delay output for the pump and boiler. Default is „ON”.

ON” position activates the pump and boiler outputs with a delay of 3 minutes after the heating signal is supplied from any of the thermostats connected to the wiring centre.
,, OFF”position causes immediate activation of the pump and boiler outputs.
ON-OFF Overrun jumper
Is used to activate the relay output for the pump when heating is satisfied. Default is,, ON”.

·,, ON” position turns OFF the pump output with a delay of 3 minutes when all thermostats stop calling for heat.
ON OFF · , OFF” position immediately turns OFF the pump output when all thermostats stop calling for heat.

PUMP AND BOILER CONTROL

8. Serial connector for PL06 and PL07 modules
It provides communication between the KL06 wiring centre and the PL06/PL07 modules. KL06 wiring centre + PL06/PL07 module increases functionality and additionally makes it possible to control the pump and/or boiler. PL06/PL07 module is powered from the wiring centre.

INSTALLATION

Remove the top cover of the wiring centre.
Unscrew the main housing (see picture).
Mount the backside of the housing to the wall. When mounting on a DIN rail, open the hooks on the back of the housing.

Remove the appropriate pices of insulation from the wires.
Thread the wires under the mounting bolt in the back part of the wiring centre.
Thread the wires through the slots in the top part of the wiring centre and connect it to the terminals.
Set includes supplementary accessories (to support the installation process).

Adjust the wires and screw the main housing of the wiring centre to the rear housing.
Connect the thermoelectric actuators wires.
Make sure that all the wires are properly connected, mount the top cover and power up the wiring centre the green”Power” indicator LED will illuminate.
INSTALLATION OF THE ADDITIONAL MODULE PL06 OR PL07 ON THE EXAMPLE OF PL06 MODULE

Remove the top cover of the wiring centre.
Connect the PL06 or PL07 module to the serial connector.
Make sure that all the wires are properly connected, mount top cover and power up the wiring centre the green,, Power” indicator LED will illuminate.
Note : Before connecting PL06/PL07 module, disconnect the main power from the KL06 wiring centre.

DISTRIBUTOR OF SALUS CONTROLS:
QL CONTROLS Sp. z o.o., Sp. k. Rona 4, 43-262 Kobielice, Poland
Importer:
SALUS Controls Plc
Units 8-10 Northfield Business Park
Forge Way, Parkgate
Rotherham, S60 1SD
United Kingdom

www.Salus-controls.pl
SALUS Controls is a member of the Computime Group.
Maintaining a policy of continuous product development SALUS Controls plc reserve the right to change specification, design and materials of products listed in this brochure without prior notice.

References

• SALUS Controls - inteligentne sterowanie temperaturą

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>