GOAL ZERO 14004 Yeti MPPT Solar Charging Optimization Module User Guide
- June 6, 2024
- GOAL ZERO
Table of Contents
SOLAR CHARGING OPTIMIZATION MODULE
USER GUIDE
IMPORTANT SAFETY INSTRUCTIONS
Please save these instructions
Read all the instructions and cautions before beginning installation.
Do NOT disassemble or attempt to repair the module.
Do NOT allow water to enter the module or the Goal Zero Yeti Lithium. Make
sure all connections are tight and secure before using.
Do NOT exceed 22V (350W) input for the module; this can cause serious damage
to the Yeti Lithium and potential bodily injury.
Check third-party solar panels specs before attempting to use them with the
module.
Do NOT chain solar panels in series (connecting positive to negative, positive
to negative, etc.), as this can result in dangerously high levels of voltage
that can cause serious damage to the Yeti Lithium and potential bodily injury.
Use ONLY with appropriate Goal Zero Yeti Lithium Portable Power Stations.
WARNING:
Never connect a power source to the module before installing it into the Yeti
Lithium. Always connect the module to the Yeti Lithium before connecting any
power source.
WARNING:
Do not exceed 22V input for the module under standard use. Doing so can cause
serious damage to the Yeti Lithium and potential bodily injury. Take note of
voltages when using third-party solar panels with the module. Do not chain
solar panels in series (positive to negative, positive to negative, etc.), as
this can result in dangerously high voltages.
GET TO KNO YOUR GEAR
HOW IT WORKS
Tools you’ll need: Screwdriver
-
Turn off all the output ports and unplug the Yeti Lithium from any power source.
-
Open the lid of the Yeti Lithium and remove the expansion module carriage from the Yeti by removing the six screws and sliding out the carriage.
a. Use both hands to work the expansion module carriage out of its position.
WARNING:
Never connect a power source to the module before installing it into the Yeti Lithium. Always connect the module to the Yeti Lithium before connecting any power source. -
Take note of the positive and negative terminals on the Yeti’s port, as well as on the blue connector.
Insert the blue module connector into the module port on the Yeti Lithium, matching positive to positive, negative to negative. -
Insert the data transfer connector on the module into the data transfer port on the Yeti Lithium.
-
Gently set in the Solar Charging Optimization Module into place, tucking the cables into the opening.
-
Using the provided four screws, secure the module into place.
-
Using the APP or 8mm ports, plug the power source into the module.
-
Know the 1V1PPT is working when the indicator light turns blue.
WARNING:
Do not exceed 22V input for the module under standard use. Doing so can cause
serious damage to the Yeti Lithium and potential bodily injury. Take note of
voltages when using third-party solar panels with the module. Do not chain
solar panels in series (positive to negative, positive to negative, etc.), as
this can result in dangerously high voltages.
INDICATOR LIGHT
FLASHING BLUE – Battery Charging BLUE – Battery Full NO LIGHT- Off FLASHING
RED – Input over-voltage, unit over-temperature, or improper connection
WHAT IS MPPT?
MPPT stands for Maximum Power Point Tracker. The Solar Charging Optimization
Module is an external MPPT and when installed properly, actively monitors the
energy source you’re using to charge the Goal Zero Yeti Lithium and optimizes
the source to maximize power, resulting in up to 40% faster charge times,
especially from solar panels. You may also notice better charge times from AC
when utilizing the Yeti Lithium’s AC charging cable plugged into the module.
FREQUENTLY ASKED QUESTIONS
Q: How many solar panels can I plug into the module?
A: There are three inputs on the module that can be used at the same time;
however, do not exceed more than 22V under standard use, as this can result in
damage to the Yeti Lithium and potential bodily injury. We recommend chaining
solar panels in parallel (positive to positive, negative to negative, etc).
We’ve taken the guesswork out of chaining when using Goal Zero Boulder Solar
Panels, the 8mm blue-ringed connector and combiner cables properly chain our
panels together for approved use with the Yeti Portable Power Stations. Please
call our solar experts at 888-794-6250.
Q: Can I plug solar panels into the module and the Goal Zero Yeti Lithium
input ports at the same time?
A: Yes; however, we recommend using the module’s inputs for solar panels since
it can optimize the charging efficiency up to 40%. You may even notice up to
20% more efficiency when charging the Yeti Lithium from the wall when using
the module.
Q: Can I use non-Goal Zero Solar Panels or a custom wiring solution or any
solar configuration that may be over 22V open-circuit voltage
A: Please call our solar experts at
888-794-6250.
TECHNICAL SPECIFICATIONS
Yeti Lithium MPPT Expansion Module
25 Amp MPPT Charge Controller
Charges the following: Approx. Charge time:
GOAL ZERO Yeti 1000 @ Max Input 3.5 hrs
GOAL ZERO Yeti 1400 @ Max Input 5 hrs
GOAL ZERO Yeti 3000 @ Max 10 hrs Input
Ports: Do not exceed 22V input under standard use
8mm Charging port 14 – 22V, Do not exceed 150W per port
Power Pole charging port 14 – 22V
Expansion Module Connector 25A MPPT charge controller (Output)
General:
Weight 1.3 lbs (583 g)
Dimensions 10.25 x 3.3 x 1.5 in (26 x 8.4 x 3.8 cm)
Warranty 12 months
Certs
GOAL ZERO HEADQUARTERS
675 West 14600 South Bluffdale, UT 84065 Designed in the U.S.A.
Made in China 1-888-794-6250
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
GOALZERO.COM SM110217
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>