DAS-4 SL26 Smartwatch User Manual
- June 6, 2024
- DAS 4
Table of Contents
SL26 User Manual
Introduction
Combining low-power Bluetooth chips and high-tech sensor technology, the
smartwatch can monitor data related to sports and health such as walking,
running, cycling, basketball, football, table tennis, heart rate, blood
pressure, and sleep. Meanwhile, it can synchronize information such as time,
weather, and messages. It is also equipped with functions such as mobile phone
loss prevention, sedentary reminder, and alarm clock reminder.
How to Wear
- Refer to the figure to correctly wear the watch.
- Buckle the watchband according to the comfort level (make the heart rate light should be close to your skin surface and avoid looseness).
Function Operations
ON/OFF
ON: long-press the key on the side for about 2s, and it will power on after a
vibration
OFF: long-press the key on the side for about 2s, and it will power off after
a vibration.
Connect the watch to your mobile phone: download and install “Fundo” on the
phone (two available ways):
- IOS and Android: scan the following QR code. After you open the interface, click Options in the upper right and use your mobile browser to open and download.
2. Android: search “FunDo” in the Y PlayStore to download; IOS: search “FunDo” in the APP Store to download.
After it is downloaded, please allow all permissions to occur during the
installation (the watch and mobile phone are required to connect to Bluetooth
3.0 and Bluetooth 4.0, ensuring that all functions can be realized).
How to connect to Bluetooth 4.0: After successfully downloading the app
and installing it, you can find a turn-on notification prompt after opening
“Fundo” and mobile Bluetooth, then click “OK”. Click “More” on the bottom
right to add devices, then search “TSO2-LE” and click to connect (note: some
Android phones need you to open its GPS function, otherwise, it may fail to
search the watch Bluetooth name);
How to connect to Bluetooth 3.0: Open the main menu of the watch
Bluetooth search Bluetooth select to activate Bluetooth click the mobile
Bluetooth name you intend to connect to gain Bluetooth connection prompt
click “OK”(allow all mobile permissions) click Bluetooth 3.0 to connect.
How to check whether it is successful to connect: When you drop down the watch
menu: the green Bluetooth icon indicates that Bluetooth 4.0 is successfully
connected; blue indicates that Blue- tooth 3.0 is successfully connected; blue
(the upper part) and green (the lower part) indicate that both Bluetooth 3.0
and 4.0 are successfully connected.
How to set message notification: Enter your mobile settings APP
management find “Fundo” permission management allow all permissions
enter notification management find “Fundo” and allow all permissions. Open
“Fundo” more APP notification open the background operation permission
enter and select “unlimited” prompt to open self-starting after return
open self-starting return – select and open APP such as QQ and WeChat that
you want to synchronize information notifications to the watch.
Note: if you log in to your WeChat account on the phone and computer at
the same time, the account on the phone won’t receive any notification. Some
mobile phones require adding “FunDo” in the power-saving white list, avoiding
being turned off when it is out of battery.
Fail to receive notifications: The watch only synchronizes notifications
from your mobile phones such as call, message, QQ, and WeChat. The watch won’t
receive any information if your mobile phone fails to receive notifications.
At this time, open your mobile settings notification function find the
corresponding APP allow the notification.
Interface switch
Dial plate switch: Long press the dial plate interface for 3s to switch dial
plates. Slide the screen left and right to switch the dial plate and click OK
to switch.
Dropdown menu: Slide the dial plate interface from the top to the bottom
and the interface shows functions such as do not disturb mode, weather,
brightness display, connection, and settings icon.
Measurement data interface: Slide the dial plate from right to left to
enter the interface that checks measurement data, then you are able to check
today’s data such as walking, sleep, heart rate, and ECG.
Notification: Slide the dial plate interface from left to right to enter
the interface that checks notifications. After the successful pairing with
your mobile phone, please open the switch of APP notification on the APP, then
notifications received by your mobile phone will be synchronized to the watch.
Main menu: Slide the dial plate interface from the bottom to the top to
enter the main menu. Enter each function and slide right to return.
Notice: sometimes, unstable connections between mobile phones and watch
Bluetooth may occur due to the inconsistent Bluetooth protocols of mobile
brands. At this time, turn off your mobile Bluetooth and try to connect again
(or restore the watch to factory settings). If system halted occurs, please
long press the ON/ OFF key for 10s to restart the watch.
Introduction to Main Functions
Notification: Enable to check instant messages of APP such as QQ and
WeChat (such function requires to connect to your mobile “FunDo”).
Pedometer: Enable to check today’s walking steps, calories burned, and
walking distance. It will automatically save all data of the day at 24:00 and
it returns to 0. Users are enabled to check all data of the day and historical
data in the APP and change daily walking goals in the step counting interface.
Sports Record: In the sports record interface, users are enabled able to
check all sports data saved in the sports mode.
ECG Monitoring: Adopting optical heart rate and ECG, it takes about 30s
to monitor data. After a successful measurement, “Topp” will appear in the
interface. Check ECG that is saved in the mobile app”Fundo”.
Sports Mode Monitoring: Multiple sports modes: running, hiking, biking,
basketball, PingPong, and football. Click “GO” after you enter any sports
mode, and it starts to work after 3s. Click the interface to continue or stop
exercises. Sports data such as the total time and calorie burned will be
displayed in the interface after you click to stop exercises. Enable Able to
delete or save such sports data.
QR Code: Scan the QR code to download and install via your mobile phone
Sleep Monitoring: Record your sleep length and quality from 9 pm to 9 am,
helping you adjust your timetable better and improve sleep quality. Slide up
and three options are displayed: status (turn on or turn off), history
(check deep sleep and light sleep length), and help (instructions in detail).
Bluetooth: Search devices you intend to connect to or disconnect the
device that is in the connected state.
Heart Rate Monitoring: Get the watch close to the wrist (the best wearing
position: the arm part above the carpal bone), and measure the real-time heart
rate value (average person: 60-90 times/second). Click the star icon at the
bottom and “it is measuring” is displayed. It takes about 20s to measure.
Telephone Directory: Synchronize 400 contacts from the mobile phone;
Call Record: Synchronize call records from the mobile phone;
Message: Synchronize messages from the mobile phone (don’t support IOS
mobile phones);
Stopwatch: Open such function to time once or multiple times;
Alarm Clock: Self-defined 5 alarm clocks: long press to delete the alarm
clock.
Dial: Connect to the mobile phone to dial (take the call on the watch).
Anti-lost: Click to find and the mobile phone will sound the alarm, or
enter the mobile APP find function and the watch will sound the alarm.
IP68 Only dustproof
and only accidental
contact with freshwater
handwashing.
www.das-4.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>