SCARLETT SC-HC63C18 Hair Clipper Set Instruction Manual

: June 6, 2024
: SCARLETT

Table of Contents

DESCRIPTION
INSTRUCTION MANUAL IMPORTANT SAFEGUARDS
DETACHABLE COMBS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

INSTRUCTION MANUAL
SC-HC63C18

www.scarlett.ru

DESCRIPTION

Blade guard
Blades
Blade adjustment lever
Housing
On/Off switch
Hanging loop
4 detachable combs
Oiler
Brush for blades cleaning

220-240 V ~ 50 Hz
Класс защиты ll| 15 W| 0.32 / 0.43 kg|
---|---|---|---

INSTRUCTION MANUAL IMPORTANT SAFEGUARDS

Please read this instruction manual carefully before use and keep in a safe place for future reference.
Before switching on the appliance for the first time please check if the technical specifications indicated on the unit correspond to the mains parameters.
For home use only. Do not use it for industrial purposes. Do not use the appliance for any other purposes than described in this instruction manual.
Do not use outdoors.
Always unplug the appliance from the power supply before cleaning and when not in use.
To prevent the risk of electric shock and fire, do not immerse the appliance in water or any other liquids.
Do not take this product to a bathroom or use near water.
The appliance is not intended for use for physically, sensory, or mentally disabled person (including children) or for persons with lack of life experience or knowledge if only they are under supervision or have been instructed about the use of the unit by a responsible person.
Children must be under control in order not to be allowed to play with the appliance. Do not leave the appliance switched on when not in use.
Do not use other attachments than those supplied.
Do not operate after malfunction or cord damage.
In case of the power cord is damaged, its replacement should be done by the manufacturer or service department or the other high-skill person to avoid any danger.
Never try to repair this appliance by yourself. In case of failure, contact the nearest seller.
Keep the cord away from sharp edges and hot surfaces.
Do not place or store the appliance where it can fall or be pulled into a tub or sink.
Do not pull, twist, or wrap the power cord around the appliance.
Never insert any objects into openings in the appliance housing.
Do not put an operating appliance on any surface, it may cause injury or damage.
Do not use the appliance with a damaged comb, or with teeth missing from the blades as injury may occur.
If the product has been exposed to temperatures below 0ºC for some time it should be kept at room temperature for at least 2 hours before turning it on.
NOTE: KEEP THE BLADES OILED.
Do not use the hair clipper when the skin is infected.
Do not use the hair clipper on animals.
The manufacturer reserves the right to introduce minor changes into the product design without prior notice unless such changes influence IM020 significantly the product safety, performance, and functions.
The manufacturing date is indicated on the unit and/or on packing as well as in accompanying documents in the following format XX.XXXX where the first two figures XX is the month of production, and following four figures XXXX is the year of production.
BLADE ALIGNMENT
Blades must be realigned if they were removed for cleaning or after replacement.
To realign the blades, simply match the teeth of the upper and lower blade up, point for point.
The end of the top blade teeth should be approximately 1.2 mm back from the lower blade. Compare your clipper blades with the sketch (pic.1).
If blade alignment is incorrect, add a few drops of oil to the blades, switch on the clipper for a few moments, switch off and unplug. Loosen screws slightly and adjust. Tighten screws after the blade is aligned.
OILING
To maintain your clipper in peak condition, the blades should be oiled after every haircut.
Do not use hair oil, grease, oil mixed with kerosene, or any solvent.
BLADE LEVER
The lever located to the left of the blades, allows easily adjust cut hair length while clipping.
The lever adds versatility to your clipper by allowing you gradually change the closeness of your cut without an attachment comb.
When the lever is in the uppermost position, the blades will give you the closest cut and leave the hair very short. Pushing the lever downwards gradually increases the cutting length.
In its lowest position, the lever will leave the hair approximately the same length as a №1 (3mm) comb.
The lever will also extend the use of your blades since a different cutting edge is used in each setting.
In addition, if extremely heavy hair cutting has jammed the blades, it will help you to remove hair that has become wedged between the two blades without removing the blades.
While the clipper is running rapidly move the lever from “close cut” to “long cut” a couple of times. Do this each time after you have finished using your clipper to keep the blades free of cut hair.
If this does not help and the clipper stops cutting, blades are dulled. Replace them with new blades.
INSTRUCTIONS FOR HAIR CUTTING
Before first use cutting blades of the machine should be thoroughly lubricated.
Wipe off any excess oil. This should be done after each use. While using the unit, untwist the cord from time to time to avoid tangling.
Before cutting always comb the hair thoroughly first.

DETACHABLE COMBS

Attachment comb №	Hair length mm/inches
№1	3 (1/8)
№2	6 (1/4)
№3	9 (3/8)
№4	12 (1/2)

Each comb attachment is marked accordingly on its outside middle surface.
To attach a comb, hold it with its teeth upward and slide onto and along the clipper blade until the front of the comb firmly seats against the clipper blade.
When you use the clipper for the first time, cut only small portions of hair.
For even cutting do not force the clipper. Also, remember to comb the hair more frequently to remove trimmed hair and check for uneven strands.
It is recommended that you start the haircut by choosing the maximum hair length, and then gradually reduce the length setting.
In order to obtain the most effective result move the device in the direction opposite to the direction of hair growth. Since hair in different head segments grows in different directions, you need to move the device in different directions as well (up, down or crosswise). See Figures 2.1-2.8.
In order to obtain a good haircut for wavy, rare or long hair, use a comb to direct the cutting block of the device. See Figure 2.6.
CARE AND CLEANING
Switch off the appliance and unplug it.
Clean and oil the appliance after each use.
Remove cut hair from the clipper with the brush enclosed.
Wipe the clipper with a dry soft cloth.
Oil the blades as mentioned above.
STORAGE
Keep the appliance in a dry place.
You may hang the cutter by providing a loop.
The blades must be oiled for the storage period.
The symbol on the unit, packing materials, and/or documentation means used electrical and electronic units and the batteries should not be tossed in the garbage with ordinary household garbage. These units should be passed to a special receiving point.
For additional information about the actual system of the garbage collection address to the local authority.
Valid utilization will help to save valuable resources and avoid negative work on the public health and environment which happens with incorrect using garbage.