SCARLETT SC-HC63C65 Hairclipper Instruction Manual

SCARLETT SC-HC63C65 Hairclipper

DESCRIPTIONS

1. Ergonomic housing
2. On/Off switch
3. Charge indicator
4. Appliance plug
5. Adapter
6. Socket
7.  Comb adjustment lever
8. Oiler
9. Brush for blades cleaning
10. Barber comb
11. Detachable telescopic comb (1-9mm)
12. Detachable telescopic comb (10-18 mm)
13. Detachable blades

STYLING

IMPORTANT SAFEGUARDS

• Please read this instruction manual carefully before use and keep in a safe place for future reference.
• Before switching on the appliance for the first time please check if the technical specifications indicated on the unit correspond to the mains parameters.
• For home use only. Do not use for industrial purposes. Do not use the appliance for any other purposes than described in this instruction manual.
•  Do not use outdoors and damp area.
•  Always unplug the appliance from the power supply before cleaning and when not in use.
•  To prevent risk of electric shock and fire, do not immerse the appliance in water or any other liquids.
•  Do not take this product to a bathroom or use near water.
•  The appliance is not intended for use for physically, sensory or mental disabled person (including children) or for person with lack of life experience or knowledge, if only they are under supervision or have been instructed about the use of the unit by responsible person.
•  Children must be under control in order not to be allowed to play with the appliance.Do not leave the appliance switched on when not in use.
•  Do not use other attachments than those supplied.
•  Do not operate after malfunction or cord damage.
•  In case of power cord is damaged, its replacement should be done by the manufacture or service department or the other high-skill person to avoid any danger.
• Never try to repair this appliance by yourself. In case of failure, contact the nearest seller.
•  Keep the cord away from sharp edges and hot surfaces.
•  Do not place or store the appliance where it can fall or be pulled into a tub or sink.
•  Do not pull, twist, or wrap the power cord around the appliance.
•  Never insert any objects into openings in the appliance housing.
•  Do not put operating appliance on any surface, it may cause injury or damage.
•  Do not use the appliance with damaged comb, or with teeth missing from the blades as injury may occur.
•  If the product has been exposed to temperatures below 0ºC for some time it should be kept at room temperature for at least 2 hours before turning it on.

NOTE: KEEP THE BLADES OILED.

•  The appliance should be used only with the power supply supplied with the appliance.
•  The instrument must be powered only by a safe, ultra-low voltage marked on the instrument.
•  Do not use the hair clipper when the skin is infected.
•  Do not use the hair clipper on animals.
•  The manufacturer reserves the right to introduce minor changes into the product design without prior notice, unless such changes influence significantly the product safety, performance, and functions.
•  Manufacturing date is indicated on the unit and/or on packing as well as in accompanying documents in the following format XX.XXXX where first two figures XX is the month of production, and following four figures XXXX is the year of production.

PREPARATION

• The device is designed for cutting hair
•  Before first use cutting blades of the machine should be thoroughly lubricated.
•  Before switching the unit on for the first time, please fully discharge and recharge the battery.
•  The charging time is 8 hours.
•  The fully charged battery ensures 45 minutes of operation.
•  Recharge the battery at least once in 6 months, even if the clipper is not in use.
•  To charge the battery, switch off the clipper and connect its power cord to mains. The indicator lamp lights.
•  When the battery has charged, disconnect the clipper from mains. The clipper is ready for operation.

OPERATION

•  You may operate the clipper, when its battery is charged, or if it is connected to the mains.
•  Take one of the supplied combs, insert the comb guides into the matching slots and gently push until it clicks.
•  Turn the length of the hair cutting at the rear of the machine, set the desired length.Turn the knob until the desired length is the figure does not coincide with the mark on the housing.
• To turn on the machine, slide the switch up.
•  When finished, turn off the machine by moving the switch down.
•  You may also use the clipper without any comb attached.

THINNING FUNCTION

• The blade allows you to use thinning function and improve quality of cutting.
• Thinning allows to make smooth passage between hair strands of different length. In this mode the blade reduces hair volume without making the hair shorter.

BLADE ATTACHMENT

• To detach the blade from the appliance, press it and pull it forward.
• To attach the blade, insert it into place and push until the click is heard.

REMINDERS

•  It is better to cut dry hair.
•  Comb hair carefully before cutting.
•  Always take off a little at a time.
•  For even cutting do not force the clipper. Also remember to comb the hair more frequently to remove trimmed hair and check for uneven strands.
•  Cutting options are given in fig. 1.

BATTERY REMOVAL

•  The battery must be removed from the appliance before its disposal.
•  When removing the battery, the appliance must be disconnected from power supply.

CARE AND CLEANING

•  To ensure continuous and reliable operation of the clipper, oil the blades using special oil after each haircut.
•  After oiling turn on the clipper to allow even distribution of oil between the blades and check their smooth operation. Remove excessive oil.
•  Do not use hair oil, grease, oil mixed with kerosene or any solvent.
•  Turn off the clipper and disconnect it from power supply.
•  Clean the blades and the clipper from hair with the help of a brush supplied.
•  Wipe the clipper with a dry soft cloth.

STORAGE

•  Keep the appliance in a dry place.
•  The blades must be oiled for storage period.

The symbol on the unit, packing materials and/or documentations means used electrical and electronic units and battery’s should not be toss in the garbage with ordinary household garbage. These units should be pass to special receiving point. For additional information about actual system of the garbage collection address to the local authority. Valid utilization will help to save valuable resources and avoid negative work on the public health and environment which happens with incorrect using garbage.

References

• Dictionary

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>