NUX NMP-2 Dual Foot Switch Owner’s Manual

: June 6, 2024
: NUX

Table of Contents

Features
Product Description
Connections
Precautions
Documents / Resources

NMP-2
Dual Foot Switch
Owner’s Manual

Copyright
Copyright 2017 Cherub Technology Co. All rights reserved. NUX and NMP-2 are trademarks of Cherub Technology Co. Other product names modeled in this product are trademarks of their respective companies that do not endorse and are not associated or affiliated with Cherub Technology Co.

Accuracy
Whilst every effort has been made to ensure the accuracy and content of this manual, Cherub Technology Co.
makes no representations or warranties regarding the contents.

WARNING
To reduce the risk of ﬁre or electric shock, do not expose this appliance to rain or moisture.

CAUTION
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The lightning symbol within a triangle means, “Electrical caution!” It indicates the presence of information about operating voltage and potential risks of electrical shock.

**** The exclamation point within a triangle means, “Caution!” Please read the information next to all caution signs.

Thank you for purchasing the NMP-2 Footswitch controller. It is a multi-foot controller specially designed for arranger instruments (Keyboards, Modules, Effect pedals…etc). Using this controller you can easily activate all the main functions of the equipment.

Features

This unit combines the functions of latch type and WTB-005 (momentary type) footswitches. Both of the unit’s footswitches may be set to function as either a latch or momentary type(Open, Close) switch.
You can connect to gear equipped with TRS 1/4” (6.35mm) phone jacks using a connection cable with stereo 1/4” (6.35mm) phone plugs at both ends.
The NMP-2 can be used with Loop Core Deluxe for phrase up/down.
It also could be used while close mode even passive status.

Product Description

Foot Switch A
Use this as a switch for the device connected to Jack A or Jack B&A. Refer to “Connections.”
Foot Switch B
Use this as a switch for the device connected to Jack B or Jack B&A. Refer to “Connections.”
Foot Switch A Indicator
When the footswitch A is set to the latch type function, this indicator alternately lights or goes out each time the footswitch is pressed. When footswitch A is set to the momentary type function(open or close), this indicator lights only while the footswitch is held down.
Foot Switch B Indicator
When footswitch B is set to the latch type function, this indicator alternately lights or goes out each time the footswitch is pressed. When footswitch B is set to the momentary type function(open or close), this indicator lights only while the footswitch is held down.
DC Jack
The NMP-2 uses 9V (Positive outside, Negative inside) 2.5mm plug to active Latch mode, open mode(also close mode with indicator).
Jack A
Connect the device being controlled with foot switch A here. Use a connection cable with 1/4” (6.35mm) phone plugs at both ends.
Jack B&A
Connect devices equipped with TRS or TS 1/4” (6.35mm) phone jacks here. Use a connection cable with stereo or mono 1/4” (6.35mm) phone plugs at both ends.
*TS(mono) is for footswitch B only. If you want to operate footswitch A and footswitch B at the same time, you must use TRS(stereo) phone plugs here.
Mode Switch
This sets the functions for footswitch A and B to LATCH or Momentary( Open, Close).
*After referring to the owner’s manual for the device you are connecting, switch this to the appropriate setting.
Open mode means while you hold the footswitch, the Tip and Sleeve is opened.(using mono cable)
Close mode means while you hold the footswitch, the Tip and Sleeve is closed.(using mono cable)

Connections

*When connecting to Jack B&A, do not plug any device into Jack A. This may result in damage and/or malfunction.

Precautions

Environment:

Do NOT use the pedal in high temperature, high humidity, or subzero environments.
Do NOT use the pedal in direct sunlight.

Please do NOT disassemble the pedal by yourself.
Please keep this manual for future reference.

CE mark for European Harmonized Standards
CE Mark which is attached to our company’s products of Battery mains the product is in full conformity with the harmonized standard(s) EN 61000-6-3:2007+A1:2011 & EN 61000-6-1:2007 Under the Council Directive 2004/108/EC on Electromagnetic Compatibility.
2017 Cherub Technology-All rights reserved. No part of this publication may be reproduced in any form without prior written permission of Cherub Technology.

www.nuxefx.com
Made in China