LENKENG LKV372AE HDMI Extender User Manual

LENKENG LKV372AE HDMI Extender User Manual

Important Safety Notice

1. Please distinguish the transmitter and receiver before installation.
2. Do not disassemble the machine to repair the product during the working process to avoid electric shock.
3. Please cut off the power before installation. Live installation may damage the equipment.
4. Do not expose the devices to rain, moisture and liquid.
5. Use a 5V/500mA DC adapter only. Make sure the specification matched if using 3rd party DC adapters.

Introduction

This HDMI Extender includes a transmitter unit and a receiver unit, allows the HDMI signal to be transmitted up to 70 meters at 1080p resolution using a Cat6/6A/7 network cable. It adopts a point-to-point connection configuration, supports IR pass-back. It is perfect for outdoor advertising, monitor system, home entertainment, conference, etc.

Features

1. Zero latency.
2. Support up to 1080p@60Hz resolution.
3. Supports Cat6/6A/7 network cables, the transmission distance is up to 70 meters.
4. Support IR pass-back function (20～60KHz).
5. Support 1080p HDR10 (YUV4:4:4).
6. Support EDID passthrough.
7. Audio formats supported: PCM, LPCM, DTS HD, DTS Audio
8. Automatically adjusts parameters to match different network cables and achieve the best display performance.
9.  Lightning Protection, Surge Protection, ESD Protection.

Package Contents

Installation Requirements

1. HDMI source device (compute graphics card, DVD, PS4, HD monitoring equipment etc.)
2. HDMI display device like SDTV, HDTV, projector with HDMI port.
3. UTP/STP CAT6/6A/7 cable, follow standard IEEE-568B, it is recommended to select a network cable with less loss and crosstalk .

Interfaces

1. Transmitter (TX)

③

|

IR Out

| Connect the IR blaster extension cable, please keep the infrared transmitter as close as possible to the signal source device when using.
④| Reset button| Press the button to restart the device.
⑤| Rj45 signal output| Output modulated HDMI signal.

⑥

| Signal Indicator| No HDMI signal is transmitted, the indicator flashes.

HDMI signal is transmitted, the indicator stays on.

2. Receiver (RX)

③

|

IR In

| Connect the IR receiver extension cable to ensure that the remote control used is within the range of the IR receiving device.
④| Reset button| Press the button to restart the device.
⑤| Rj45 signal output| Input modulated HDMI signal.

⑥

|

Signal Indicator

| No HDMI signal is transmitted, the indicator flashes.

HDMI signal is transmitted, the indicator stays on.

Disclaimer

The product name and brand name may be registered trademark of related manufactures. ™ and ® may be omitted on the user manual.
The pictures in this user manual are just for reference. The terms HDMI,
HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
We reserve the rights to make changes without further notice to a product or system described herein to improve reliability, function or design.

Installation Procedures

1.  The network cable should follow the standard of IEEE-568B. It is recommended to select a network cable with less loss and crosstalk.
   1-Orange/white 2-Orange 3-Green/white
   4-Blue 5-Blue/white 6-Green
   7-Brown/white 8-Brown

2. Connection

3 Connection instruction

1. Connect the HDMI port of the source device to the HDMI IN port of the transmitter via an HDMI cable.
2. Connect the CAT6 OUT port of the transmitter and the CAT6 IN port of the receiver via a network cable.
3. Connect the HDMI port of the display device to the HDMI OUT port of the receiver via an HDMI cable.
4. Connect the IR blaster extension cable to the IR OUT port of the transmitter, connect the IR receiver extension cable to the IR IN port of the receiver.
5. Plug the power into the devices to get started.

• FAQ

Q：Why there is no image/image or sound is not played smoothly?
A：Press the “RESET” button of the receiver to restart the device. Reconnect the devices with a shorter network cable
Q：Why does the signal indicator “LINK” always flashes?
A：1）Check whether the network cable is uses IEEE-568B wiring standards.
2）Check whether the source device and the transmitter are connected well.
3）Reset the transmitter or receiver and connect it again.
Q：Why does the receiver ‘s signal indicator ”LINK” stays on but there is no image output?
A：1）Press the “RESET” button of the receiver to restart the device.
2）Check whether the display device and the receiver are connected well.
3）Reconnect the network cable or re-power the receiver.

Specification

| HDMI compliance|
HDCP compliance|

HDMI resolution

| 800×600、1024×768、1280×720、

1280×960、1366×768、1440×900、

1680×1050、1920×1080、480i@60Hz、

480p@60Hz、576i@50Hz、

576p@50Hz、720p@50/60Hz、

1080i@50/60Hz、

1080p@24/25/30/50/60Hz

Audio formats| DTS、DTS-HD、PCM、LPCM
HDR| Support
EDID through| Support
IR Pass-back| Frequency Range：20~60KHz
Input and output TMDS signal| 0.7~1.2Vp-p(TMDS)
Input and output DDC signal| 5Vp-p(TTL)

Transmission Distance

| Cat6/6A/7| ≤70 Meters
|

Electrostatic protection of the whole machine

| Implementation of the standard: IEC61000-4-2

1a Contact discharge level 4 (8KV) 1b Air discharge level 4 (15KV)

| Working temperature| -20~60℃
Storage temperature| -30~70℃
Humidity (no condensation)| 0～90%RH
| Dimension| 71.6(W) x 66.6(D) x 24.8(H) mm
Weight|
Color| Black

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>