Lenkeng LKV655KVM Full HD HDMI KVM Wireless Extender User Manual

Lenkeng LKV655KVM Full HD HDMI KVM Wireless Extender User Manual

Disclaimer

The product name and brand name may be registered trademark of related manufactures. ™ and ® may be omitted on the user manual. The pictures in this user manual are just for reference. We reserve the rights to make changes without further notice to a product or system described herein to improve reliability, function or design.

Important Safety Instructions

1. Do not expose this device to rain or place it near water. Any liquid that goes into the device may cause a failure, fire, or electric shock.
2. Never insert anything metallic into the open parts of this device. This may cause a danger of electric shock.
3. Do not place this device near or over a radiator or heat register, or where it is exposed to direct sunlight.
4. The device should be repaired only by a qualified technician.
5. If a third-party power supply is used, please ensure that the power supply specifications meet the product requirements.

Introduction

This is a Full HD HDMI KVM wireless extender, including a transmitter and a receiver. Adopting color STREAM technology can realize high definition and low-latency transmission. Based on the 5G wireless frequency band, with stable anti-interference and safety performance. It supports 1-to-1 wireless transmission, and the transmission distance can reach 50 meters, effectively solving problems caused by complicated wiring. It’s an ideal wireless video transmission solution for video conferences, home entertainment, multimedia education, etc.

Note：

1. Transmission distances may vary depending on the environment.
2. Signals may be reduced or completely lost by solid structures such as walls, bricks, and glass.
3. The surrounding wireless signal may cause certain interference to the transmission, and the channel can be switched to reduce the interference.

Features

1. Adopting ipcolor STREAM technology can realize high definition and low-latency transmission.
2. Support up to 1920×1200@60Hz/1920×1080@60Hz resolution, backward compatible.
3. Support wireless transmission up to 50 meters (line of sight).
4. The transmitter supports HDMI loop out.
5. In case of multiple sets of products in the same area, support SSID pairing and channel switching to avoid interference.
6. Support IR passback.
7. Support 5G wireless frequency bands, strong anti-interference.
8. Support KVM control signal passback.
9. Support firmware upgrade via Micro USB port.

Package Contents

• Transmitter x1

• Receiver x1

• 5V 1A power adapter x2

• IR receiver extension cable x1

• IR blaster extension cable x1

• Antenna x4

• Mounting ear x4

• Screw x10

• Grounding screw x2

• User manual x1

• USB cable x1

Installation Requirements

1. HDMI source device (DVD, game console, PC, etc.)
2. HDMI display device (TV, projector, LED screen, etc.)

Panel Description

Transmitter (TX)

connection successful) Quick flash: SSID Pairing mode
③| Signal indicator| a) Light off: no HDMI signal
b) Steady on: HDMI signal is transmitting) Quick flash: restore factory settings
④| KVM indicator| Light flashing : The KVM data is transmitting)
Steady on: The computer and the USB port reconnected
⑤| USB-A port| Connect to the computer with USB cable
⑥| Channel switch button| a) press to switch channels}
b) Press and hold 5s for SSID pairingc) Press and hold 10s for restore factory settings
⑦| Antenna connectors| Connect with antennas
⑧| Micro USB port| Used for firmware upgrade
⑨| HDMI input| Connect with HDMI source device with HDMI cable
⑩| HDMI output| Connect with local HDMI display device with HDMI cable
| IR out| Connect with IR blaster extension cable
| Power input| Connect with DC 5V/1A power adapter

Receiver (RX)

: connection successfulc) Quick flash : SSID Pairing mode
③| Signal indicator| a) Light off : no HDMI signalb)
b Steady on : HDMI signal is transmittingc)
c Quick flash : restore factory settings
④| KVM indicator| 1) Light flashing : The KVM data is transmitting
2) Steady on : The mouse and the keyboard are connected
⑤| USB-A port| Connect the mouse and the keyboard
⑥| Channel switch button| a) After connecting with TX, press to switch channelsb) Press and hold 5s for SSID pairingc) Press and hold 10s for restore factory settings
⑦| Antenna connectors| Connect with antennas
⑧| Micro USB port| Used for firmware upgrade
⑨| HDMI output| Connect with HDMI display device with HDMI cable
⑩| IR in| Connect with IR receiver extension cable
| Power input| Connect with DC 5V/1A power adapter

Installation Procedures

Connection Diagrams
One to one connection

Connection Instructions

1. Connect the source device to the HDMI IN port of the transmitter with an HDMI cable, and connect the HDMI OUT port of the receiver to the display device with another HDMI cable.

2. If using the IR pass back function, connect the IR blaster extension cable into the IR OUT port of the transmitter, and connect the IR receiver extension cable into the IR IN port of the receiver.
   a: The emitter of the IR blaster extension cable should be as close as possible to the IR receiving window of the source device.
   b: Point the remote control at the receiving head of the IR receiver extension cable to operate.

3. If using the KVM function, connect the keyboard/mouse to the USB port of the receiver and connect the computer to the USB port of the transmitter via the USB cable

4. Plug the power supply into the devices to get started.

5. In the case of multiple sets being used at the same time in the same area.
   In order to prevent mutual interference, switch each set of transmitters and receivers to a different channel after they have been manually paired with the SSID.

SSID Pairing

1. Enter the SSID pairing mode by holding the transmitter and receiver’s channel switch buttons for five seconds. Both WiFi connection indicators will flash quickly in yellow.
2. When the SSID pairing is successful, the WiFi indicators on the transmitter and receiver will change from quick flashing to slow flashing or steady on.

FAQ

A: 1) Move transmitter and receiver closer. 2) Re-power the transmitter or receiver. 3) Re-pair the transmitter and receiver.

A: 1) Make sure the TX has HDMI input and that the resolution is within the specified range. 2) Try to connect the signal source directly to the display device, or change the signal source and HDMI cable and test again.

Q: Why is the display stuttering or unstable?

A: 1) Place the transmitter or receiver within the signal coverage and minimize obstructions between the transmitter and receiver. 2) Switch to a different channel to avoid interference from other wireless signals. 3) Re- power the receiver or transmitter

Specification

1024×768, 1280×720,1280×960, 1366×768, 1440×900, 1680×1050,1920×1080
Input and output TMDS signal| 0.7~1.2Vp-p（TMDS）
Input and output DDC signal| 5Vp-p（TTL）
**Transmission| Wi-Fi Frequency bands| 5.18~5.24 GHz
Transmission distance| ≤ 50m
Latency| 70~100ms
Connection types| One-to-one
SSID pairing| Supported
Protection Level| ESD protection| 1a Contact discharge level 3 1b Air discharge level 3 Standard: IEC61000-4-2
IR Performance| Infrared frequency| 20~60kHz
Receiving range| ≤ 5m
****Operating Environment| Working temperature| -20~60℃
Storage temperature| -30~70℃
Humidity (no condensation)| 0~90% RH
TX: 115(W) x 125(L) x 20.6(H) mmRX: 115(W) x 125(L) x 20.6(H) mm
Color| Black
Iron
Net weight**| TX: 346g; RX: 338g

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>