4lite GU10 Fire Rated Downlight Instruction Manual
- June 6, 2024
- 4lite
Table of Contents
Description – GU10 Fire Rated Downlight
Installation Instructions
**Luminaire Code(s) – 4L1/220***
General Installation Instructions
These instructions should be read carefully prior to any installation and retained after completion for further reference and maintenance. Please give these instructions to the building owner/occupier after installation.
Important Safety
- Betas Installation. maintenance or lamp replacement_ ensure that the mains supply to the luminaire is switched off and the circuit supply fuses are removed or the moue breaker s turned off.
- ft is recommended that only a qualified electrical contractor carries (xit the installation et this luminaire and that tna luminaire is installed in compliance with the current edition of the IEE Wiring Regulations
- The person carrying out trio installation is to check and verify that the total load on the circuit including that of this luminaire does not exceed the rating ct the circuit cable. fuse a circuit breaker.
- Where a luminaire incorporates discharge control gear inductive load). the circuit capacity and ratings require careful siting to avoid nuisance tnpp. ng of the protective device used in the installation.
- Where applicable, careful consideration should be taken dunng installation to ensure that all fixings andra suspensions are of a suitable site for the Owninaire being instated.
Retinas
- At luminaires are manufactured & tested in compliance with the requirement contained within BS EN 130598 and are CE marked
- All luminaires that are of Class 1 construction are marked accordingly. MUST be earthed
- Al] luminaires are tieskjned to operate at 230Volts AC -6%410% a 216Volts to 252Voltt. Do not operate outside these voltages.
- Al luminaires are only suitable for applications within their rated Ingress Protection Inns as stated. S. This luminaire is designed for internal use only.
Exclusions to Warranty
Please Note –
The limited warranty shall be null and void in the ‘allowing circumstances.
Farina by the installer, end-user or any third party to exercise caution to
protect any covered product or part from outside damage, adverse temperature
(normal operating ambient temperature 0 25t), humidity conditions,
fluctuations in the electrical system, or ptlysicrg abuse as wee as nature
related to the workmanship in the installation of the products or parts.
Installation
- Select a suitable mounting location to install the luminaire. Care should be given to ensure adequate ventilation for the luminaire as this luminaire operates at high temperatures_ Check that sufficient depth is available in the ceiling void and there is adequate free air ventilation around the luminaire
- Ensure luminaire is not located in close proximity to ceiling joists, electrical cables, and pipework or insulation materials. Luminaires should not be installed where the illuminated surface is within 0 5m from the front of the fitting
- Cut a 76mm diameter round hole in the ceiling material. This luminaire is suitable for installation in ceiling material thickness from 10rnm to 25mm
- GU10 Mains (230V)
- Terminate the 230V supply cable max 2 x 1.5mm loop in — loop out ensuring the correct polarity s observed This luminaire is designed to accept up to a 60W GU10 Lamp. THIS LUMINAIRE IS CLASS I CONSTRUCTION USED WITH GU10 LED MAINS LAMPS, AND MUST BE EARTHED.
- Offer the luminaire through the aperture. bend back the springs and push gently into the ceiling. Do not install the laminate onto new plaster or wet paint
- Remove the Twistlock lamp retaining ring by twisting in an anti-clockwise direction Insert the appropriate lamp type, position the lamp into the retaining clip Return the retaining ling into the luminaire housing, and hyist firmly in a clockwise direction to lock the ring into position
- Restore the power supply, switch on and test for correct operation
- Important Installation Advice:
- Im is recommended to allow a void of space around the downlight
- When used with 50W GU10 is not suitable to be installed into flammable material.
Maintenance:
- Lamp Cap GU10 Maximum wattage – 5CW
- 4Lite recommends the use of recognized branded lamps
Disposal of Electronic Equipment WEEE Directive 20021961EC
This product falls within the scope of the Waste Electrical & Electronic
Equipment Directive (WEEE), which means the product should not be disposed of
as normal household waste Ensure that this luminaire and lamp is disposed of
in accordance with the WEEE Directive Contact a ‘local Council Waste Dept
Local Amenity Site or the Environment Agency for further information RoHS –
Ail components and materials used in this product are RoHS 2002/95:EC comohant
Installation Instructions
Wireless Specifications
Wreless RF mode 4equancy band 2400 – 24835 MHZ
Minimum transmitted bower 20 dem
Operating chemels wi-fi 13/9 channels
Operating chemels Bluetooth 40 charnels
The product that is not be used with riot for daring use the WIZ application
On-off functionality is available without Wi-fi cornectryity.
WI-fi registered trademark of W,-Fi Alliance WPA trademark of Wi-Fi alliance
WPAZ ‘ is a trademark of the Wi-Fi alliance. The WI-Fi CERTIRED TM Logo is a
certification mark of the Wi-Fi alliance
Amazon, Alexa, and all related logos are trademarked of
Amazon.com.Inc or it; officiates Google is a trademark of
Google LLC Siri a registered trademark of Abele Inc.
The Bluetooth word erd logos are regctexed written owhed by Bluetooth SIG.INC
Hereby, [WC Connected lighting Ca, Limited] declares that the radio equipment
type [WC Performance lemps] is in compliance with directive 2o14/53/EU
The FULL text of the EU declaration of conformity is available at the
Internet address wizconnected.com
QUICKSTART GUIDE
TROUBLESHOOTING
My lights won t pair in the wi Connected App or an optimal pairing experience with wi Connected products make sure your wuss router is operating on 4Gr or alternatively follow the in-App support to pair the products manually or that with the support team
Check that Ms lamp or trip is within Whal raps.
Check that your phone is connected to the 2.4GHZ wi-fi on your home
routes.
You can switch back to 5 GHz after paring is done
Follow the prompts on the yam app screen
How do I make sure my lights are In parring mode?
When you repeatedly power ON your light It should be Stat to pulse in blue
color light or when to tumble white Of dimmable Light).
The pulsing means your light is reedy so pair.
If no light Is fount try Manual Setup
I am not sure how to connect to the 2.4Ghz networks_ What should I do?
Tap on Try manual setup’. Walt for the next Sceran to open and follow the
Instructions, Which will make you open the Wi-Fi settings of your phone and
connect to wi-fi WIZCsatig_XXXX
When The light is in MUnal Setup mode and emails a WI-Fi signal it will pulse
in purple (calor light Or white (tunable White dimmable light).
Still, having a problem? Contact the support team via app.
Waning; Dimmer switch is net supported by wiz lights and may damage the
product
If will warn to use it regardless make sure the dimmer is ai 100%.
Tip! Metalitiencleaed shades or futares may hamper connectivity.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>