legrand WNRL10 Radiant Smart Switch Instructions
- June 6, 2024
- Legrand
Table of Contents
WNRL10 Radiant Smart Switch
Instructions
radiant® WNRL10 Smart Switch with Netatmo Incandescent, Halogen: 1800W;
Resistive: 120VAC, 60Hz, 15A; Standard + Electronic Ballast: 15A; Motor: 1/2
HP
Interrupteur intelligent radiant® WNRL10 avec Netatmo; Incandescente, halogène
: 1800 W;
REGULATORY INFORMATION
FCC NOTICE: This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 10 mm between the transmitter’s radiating structure(s)
and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly
approved by the manufacturer will void the warranty and the user’s authority
to operate the equipment.
Contains FCC ID: 2AU5D982057
IC NOTICE: This device complies with Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions: (1) this
device may not cause interference; and (2) this device must accept any
interference, including interference that may cause undesired operation of the
device.
RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits
given in RSS-102 Issue 5 requirements at the minimum separation distance of 10
mm to the human body. Note: Any changes or modifications to this device that
are not expressly approved by the manufacturer, will void the warranty and the
user’s authority to operate the equipment.
IC: 25764-982057
HVIN: 982057
BEFORE YOU START
Review this guide in its entirety. Consult an electrician with any questions
or if you are unsure of your abilities.
Warning: Incorrect installation could result in death, serious injury,
and/or damage to your home or devices.
Caution: To reduce the risk of injury and/or overheating and damage to
other equipment:
- For dry, indoor use only.
- Do not use to power medical equipment – not suitable as a disconnecting means.
- Do not use with loads exceeding the device load rating.
- Connect the smart switch to a 120 VAC, 60 Hz power source ONLY.
- Always use copper wire to install the smart switch & follow all applicable local & national electrical codes.
WHAT YOU NEED
Required:
- Phillips-head screwdriver
- Flat blade screwdriver
You May Also Need:
Voltage tester, pliers, wire cutter, wire stripper, electrical tape,
flashlight, wiring leads (included), and wire nuts (included).
INSTALLATION & SETUP
-
Turn off power to device at the circuit breaker
Flip existing light switches multiple times to confirm power is off.
NOTE: Ensure power is off to all devices in the electrical box. -
Remove existing device
Check for the following wires:
a. HOT or LINE: Receives power from the circuit box. Referred to as “hot” for the purpose of this guide. Do not touch or let “hot” wire contact other wires.
b. LOAD: Directs power to your
light(s).
c. NEUTRAL: Creates a path to return current to the power source when the device is off. Required for your switch installation.
d. GROUND: Provides a safe path for electricity in the event of a short circuit. -
Wire Smart Switch
Use the wire nuts provided to secure the wires together.
a. Connect the WHITE neutral wire on the switch to the neutral wires in the box, using the red wire nut.
b. Connect the LOAD wire on the switch to the load wire(s) in the box.
c. Connect the HOT wire on the switch to the hot wire(s) in the box.
d. Connect the GREEN ground wire on the switch to the ground wire(s) in the box. -
Secure Smart Switch
a. Fold the wires into the electrical box, taking care not to pinch a wire.
b. Use included screws to secure the smart switch to the electrical box. Do not fully tighten the screws.
-
Test The Smart Switch
NOTE: See getting to know your switch section for feature details. Turn the power back on at the circuit breaker, press the switch to turn the light on/off. This device is designed to work with a radiant ® Smart Gateway with Netatmo.
Follow the instructions from your app to finish setting up your switch.
TROUBLESHOOTING TIP : If the device is not powering check
wiring to determine if you have reversed the “HOT” and “LOAD” wiring. -
Attach Wall Plate
a. Use the sub-plate screws (provided) to secure the sub-plate to the smart switch.
b. Tighten device screws to secure the smart switch to the electrical box.
c.Angle the UP end of the wall plate over the top edge of the sub-plate.
Push the screwless wall plate down and in until it “snaps” into place over the sub-plate.
NOTE: To remove the wall plate, place the tip of a flat blade screwdriver into the slot under the wall plate and twist gently. -
Set Up Your System
a. Download and launch the Legrand Home + Control app. The app is available on the App Store or on Google Play.
b. Connect your smart device to your home network by following the step-by- step instructions in the app.
c. Use the app to control your smart device.
For the most recent instruction sheets or more information on this product, please see this link or scan the QR code: https://www.legrand.us/p/wnrl10wh
https://www.legrand.us/p/wnrl10wh
GETTING TO KNOW YOUR SWITCH
| Item | Name | Description |
|---|---|---|
| 1 | Paddle Switch | Press the top of the paddle to turn the light on and the |
bottom of the paddle to turn the light off.
2| LED Loca- for Light| Indicates the current state of the device. Refer to
“LED Locator Light Explanations” for detail.
3| EZ Button| Used to enter setup mode.
LED Locator Light Explanations
| State of Light | Explanation |
|---|---|
| Solid White | Lit when the load is off. |
| Solid Red | Factory reset, not in-network. |
| Blinking Green | The device is attempting to connect to the network. |
| Solid Green | The device in the network is temporarily open. |
Reset To Factory Default
Deleting a device from the app will reset it to factory defaults.
To manually reset the device to factory defaults press and hold the EZ button
for 10 seconds until you see the LED blink red then release. The LED will
change to solid red when the reset is complete.
SPECIFICATIONS
| Load | Rating |
|---|---|
| Resistive | 120 VAC, 60 Hz, 15 A |
| Incandescent/Halogen | 1800 W |
| Ballast | 15 A standard/electronic |
| Motor | 1/2 HP |
Legrand reserves the right to change specifications without notice.
LIMITED ONE YEAR WARRANTY
Legrand will remedy any defect in workmanship or material in Legrand products
that may develop under proper and normal use within ONE year from date of
purchase by a consumer:
(1) by repair or replacement, or, at Legrand’s option, (2) by the return of an
amount equal to the consumer’s purchase price. Such remedy is IN LIEU OF ANY
AND ALL EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Such remedy by Legrand does not include or cover the cost
of labor for the removal or reinstallation of the product. ALL OTHER FURTHER
ELEMENTS OF DAMAGE (INCIDENTAL OR CONSEQUENTIAL DAMAGES) FOR BREACH OF ANY AND
ALL EXPRESSED OR IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED HEREBY. (Some states do not
allow disclaimers or exclusion or limitation of incidental or consequential
damages, so the above disclaimer and limitation or exclusion may not apply to
you.) ANY IMPLIED WARRANTIES INCLUDING WHERE REQUIRED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE
ONE YEAR PERIOD SET FORTH ABOVE. (Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you.)
To ensure safety, all repairs to Legrand products must be made by Legrand, or
under its specific direction. Procedure to obtain performance of any warranty
obligation is as follows: (1) Contact Legrand, Syracuse, New York 13221, for
instructions concerning return or repair; (2) return the product to Legrand,
postage paid, with your name and address and a written description of the
installation or use of the Legrand product, and the observed defects or
failure to operate, or other claimed basis for dissatisfaction. This warranty
gives you specific legal rights and you may also have other rights which vary
from state to state.
For covering patents, see www.legrand.us/patents
No: 341305 2/21
© Copyright 2021 Legrand All Rights Reserved.
Questions? We’re here to help.
Phone: 1-877-833-3303 8:00 a.m. to 8:00
p.m. EST (M-F)
Email: smartlighting@legrand.us
Chat: https://www.legrand.us/radiant/smart-lighting.aspx
(Click on the chat icon to open a dialogue box)
800.223.4185
1.877.BY.LEGRAND
www.legrand.us
www.legrand.ca
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>