SKIL DL527501 20V 1-2 Inch Drill Driver Owner’s Manual

Owner’s Manual

Model : DL527501
20V 1/2″ Drill Driver

WARNING: To reduce the risk of injury, the user must read and understand the Owner’s Manual before using this product. Save these instructions for future reference.

For Customer Service
1-877-SKIL-999 OR
www.skil.com

WARNING

• Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals are:
  – Lead from lead-based paints.
  – Crystalline silica from bricks, cement, and other masonry products.
  – Arsenic and chromium from chemically treated lumber.

• Your risk from these exposures varies, depending upon how often you do this type of work. To reduce your exposure to these chemicals:
  – Work in a well-ventilated area.
  – Work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
  – Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote the absorption of harmful chemicals.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work Area Safety
Keep work area clean and well lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical Safety
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching
outlets will reduce the risk of electric shock. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
Personal Safety
Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hats or hearing protection used for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust- related hazards.
Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
Power Tool Use And Care
Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate at which it was designed. Do not use the power tool if the switch does not turn on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
Battery Tool Use And Care
Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 265 °F may cause an explosion. Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
Service
Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

SAFETY WARNINGS FOR DRILL DRIVER

Safety instructions for all operations:
Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Safety instructions when using long drill bits:
Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
Always start drilling at low speed and with the bit tip in contact with the workpiece.
At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.

SYMBOLS

Safety Symbols
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding.
The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Owner’s Manual, including all safety alert symbols such as “DANGER,” “WARNING,” and “CAUTION” before using this tool. Failure to following all instructions listed below may result in electric shock, fire, and/or serious personal injury.

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

| This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
     **DANGER| DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
     ****WARNING| WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
    ****CAUTION **| CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages
These inform the user of important information and/or instructions that could lead to equipment or other property damage if they are not followed. Each message is preceded by the word “NOTICE”, as in the example below:
NOTICE: Equipment and/or property damage may result if these instructions are not followed.

WARNING
The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend a Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.1.

SYMBOLS (CONTINUED)
IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely.

speed, orbits, etc. per minute
0| Off position| Zero speed, zero torque…
| Selector settings| Speed, torque, or position settings. Higher number means greater speed
| Infinitely variable selector with off| Speed is increasing from 0 setting
| Arrow| Action in the direction of arrow
| Alternating current| Type or a characteristic of current
| Direct current| Type or a characteristic of current
| Alternating or direct current| Type or a characteristic of current
| Class II tool| Designates Double Insulated Construction tools.
| Earthing terminal| Grounding terminal
| Li-ion RBRC seal| Designates Li-ion battery recycling program
Symbol| Name| Designation/Explanation
---|---|---
| Ni-Cad RBRC seal| Designates Ni-Cad battery recycling program
| Read manual symbol| Alerts user to read manual
| Wear eye protection symbol| Alerts user to wear eye protection

SYMBOLS (CERTIFICATION INFORMATION)
IMPORTANT: Some of the following symbols for certification information may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely.

Laboratories.
| This symbol designates that this component is recognized by Underwriters Laboratories.

| This symbol designates that this tool is listed by Underwriters Laboratories, to United States and Canadian Standards.
| This symbol designates that this tool is listed by the Canadian Standards Association.
| This symbol designates that this tool is listed by the Canadian Standards Association, to United States and Canadian Standards.
| This symbol designates that this tool is listed by the Intertek Testing Services, to United States and Canadian Standards.
| This symbol designates that this tool complies with NOM Mexican Standards.

GET TO KNOW YOUR DRILL DRIVER

20V Drill Driver

SPECIFICATIONS

OPERATING INSTRUCTIONS

WARNING
To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack, or charger in fluid or allow fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, bleach or bleach-containing products, etc., can cause a short circuit.
WARNING
If any parts are damaged or missing, do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.
WARNING
Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious injury.
WARNING
To prevent accidental starting that could cause serious personal injury, always remove the battery pack from the tool when assembling parts.
This cordless drill driver must be used only with the battery packs and charger listed below:

SC535801 SKIL QC536001

NOTICE: Please refer to the battery and charger manuals for detailed operating information.

To Attach/Detach Battery Pack
Lock the trigger switch “OFF” on the tool by placing the direction-of-rotation (forward/ center-lock/reverse) selector in the center position.
To attach the battery pack:
Align the raised rib on the battery pack with the grooves in the tool, and then slide the battery pack onto the tool (Fig.1).
NOTICE: When placing the battery pack on the tool, be sure that the raised rib on the battery pack aligns with the groove in the tool and that the latches snap into place properly. Improper attachment of the battery pack can cause damage to internal components.

To detach the battery pack:
Depress the battery release button, located on the front of the battery pack, to release the battery pack. Pull the battery pack out and remove it from the tool (Fig. 2).
WARNING
Battery tools are always in operating condition. Therefore, the direction- of-rotation (forward/center-lock/reverse) selector should always be locked in the center position when the tool is not in use or when carrying it at your side.

Direction-of-Rotation (Forward/Center-Lock/Reverse) Selector
WARNING
After tool use, lock the direction-of-rotation selector in the “OFF” position (center-lock) to help prevent accidental starts and possible injury.
Your tool is equipped with a direction-of-rotation selector, located above the trigger switch.
This selector is designed for changing the direction of rotation of the bit and for locking the trigger in the “OFF” (center-lock) position (Fig. 3).
a. Position the direction-of-rotation selector to the far right of the tool for forwarding rotation.
b. Position the direction-of-rotation selector to the far left of the tool for reverse rotation.
c. Setting the switch in the “OFF” (center-lock) position helps reduce the possibility of accidental starting when not in use.
NOTICE: To prevent gear damage, always allow the drill driver to come to a complete stop before changing the direction of rotation.
NOTICE: The drill driver will not run unless the direction-of-rotation selector is engaged fully to the left or the right.
Variable-Speed Trigger Switch

Your tool is equipped with a variable-speed trigger switch. The tool can be turned “ON” or “OFF” by depressing or releasing the variable-speed trigger switch.
The variable-speed trigger switch delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure (Fig. 4).

Two-Speed Gearbox Switch

Your tool is equipped with a two-speed gearbox designed for drilling or driving at LO (1) or HI (2) speeds. A slide switch is located on the top of the tool to select either LO (1) or HI (2) speed (Fig. 5).
LO (1) speed provides higher torque and slower drilling speeds for heavy-duty work or for driving screws, drilling large diameters, or tapping threads. Use LO (1) speed for starting holes without a center punch, drilling metals or plastic, drilling ceramics, or in applications requiring a higher torque.
HI (2) speed provides lower torque and faster speeds for lighter drilling work. HI (2) speed is better for drilling wood and wood composites.

NOTICE: To prevent gear damage, always allow the drill driver to come to a complete stop before changing between High speed and Low speed.

Torque-Adjustment Ring

Your tool features 17+1 clutch settings. Output torque will increase as the clutch ring is rotated from 1 to 17. The drill “ ” position will lock the clutch to permit drilling and driving for heavy-duty work (Fig. 6).
When using the drill driver for different driving applications, increase or decrease the torque in order to help prevent damaging screw heads, threads, workpieces, etc.
The proper setting depends on the job and the type of bit, fastener, and material you will be using. In general, use greater torque for larger screws. If the torque is too high, the screws may be damaged or broken. For delicate operations, such as removing a partially stripped screw, use a low torque setting. For operations such as drilling into hardwood, use a higher torque setting.
CAUTION Do not adjust the torque when the tool is running.

LED Worklight
Your tool is equipped with an LED work light, located on the base of the tool, that illuminates when the variable-speed trigger switch is squeezed. This provides additional light on the surface of the workpiece for operation in lower light areas (Fig. 7).
The LED work light will automatically turn on with a slight squeeze on the trigger switch before the tool starts running, and will turn off 8 to 12 seconds after the trigger is released.
When the tool and/or battery pack becomes overloaded or too hot, the internal sensors will turn the tool off. If the tool and/or battery pack are overloaded, the LED worklight will rapidly flash. Rest the tool for a while or place the tool and battery pack separately under airflow for cooling.
The LED worklight will flash more slowly to indicate that the battery is at low battery capacity. Recharge the battery pack.
Install and Remove Bits

WARNING
Do not use the power of the drill driver while grasping chuck to loosen or tighten the bit. Friction burn or hand injury is possible if attempting to grasp the spinning chuck.
WARNING
Do not use bits with damaged shanks.
Your tool is equipped with a keyless chuck to tighten or release drill bits in the chuck jaws. The arrows on the chuck indicate the direction in which to rotate the chuck body in order to GRIP (tighten) or OPEN (release) the chuck jaws on the drill bit.
a. Lock the trigger switch “OFF” on the tool by placing the direction-of- rotation (forward/centerlock/reverse) selector in the center position.
b. Remove the battery pack and rotate the torque-adjustment ring to the drill setting “ ”.
To install the bit:
a. Rotate the chuck body counterclockwise, viewed from chuck end, to open the chuck to approximately the drill bit diameter.
b. Insert a clean bit up to the drill-bit flutes for small bits, or as far as it will go for large bits. Close the chuck by rotating the chuck body clockwise and securely tighten it by hand (Fig. 8).

To remove the bit:
a. Rotate the chuck body counterclockwise, as viewed from the chuck end, to open the chuck.
b. Remove the bit.

WARNING
Use protective gloves when removing the bit from the tool, or first allow the bit to cool down. The bit may be hot after prolonged use.

Removable Belt Clip

Your tool is equipped with a removable belt clip that can be positioned on the left side of the tool for convenient transport (Fig. 9).
Install the belt clip onto the tool:
a. Remove the battery pack from the tool.
b. Align the rib of the belt clip with the threaded hole on the base of the tool.
c. Insert the screw and securely tighten the screw with a screwdriver.
Remove the belt clip from the tool:
d. Remove the battery pack from the tool.
e. Use a screwdriver to loosen the screw that attaches the belt clip to the tool.
f. Remove the screw and the belt clip.

Drill Bits

Always inspect drill bits for excessive wear. Use only bits that are sharp and in good condition.
Twist Bits: Available with straight and reduced shanks for wood and light-duty metal drilling.
High-speed bits cut faster and last longer on hard materials.
Carbide-Tipped Bits: Used for drilling stone, concrete, plaster, cement, and other unusually hard nonmetal materials. Use continuous, heavy feed pressure when using carbide-tipped bits.
Drilling (Fig.10)

WARNING
Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If the operation is dusty, also wear a dust mask.

a. Check that the direction-of-rotation selector is at the correct setting (forward or reverse).
b. Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates.
c. Hold the drill firmly and place the bit at the point to be drilled.
d. Squeeze the trigger switch to start the drill driver.
e. Move the drill driver bit into the workpiece, applying only enough pressure to keep the bit “biting”. Do not force the drill driver or apply side pressure to elongate a hole. Let the tool do the work.
f. When drilling hard, smooth surfaces, use a center punch to mark the desired location of the hole. This will prevent the drill bit from slipping off-center as the hole is started.
g. When drilling metals, use light oil on the drill bit to keep it from overheating. The oil will prolong the life of the bit and increase the drilling action.
h. If the bit jams in the workpiece or if the drill driver stalls, stop the tool immediately. Remove the bit from the workpiece and determine the reason for jamming.
NOTICE: There are two rules for drilling hard materials. First, the harder the material, the greater the pressure you need to apply to the tool. Second, the harder the material, the slower the speed should be. If the hole to be drilled is fairly large, drill a smaller hole first, then enlarge to the required size with a larger bit; it’s often faster in the long run than drilling a larger hole initially.

Wood Drilling

For maximum performance, use high-speed steel or brad-point bits for wood drilling.

a. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
b. Increase speed as the drill bit bites into the material.
c. When drilling “through” holes, place a block of wood behind the workpiece to prevent ragged or splintered edges on the backside of the hole (Fig. 11).

NOTICE: Bits may overheat unless pulled out frequently to clear chips from the flutes.

Metal Drilling

For maximum performance, use high-speed steel bits for metal or steel drilling.
a. When drilling metals, use light oil on the drill bit to keep it from overheating. The oil will prolong the life of the bit and increase the drilling action.
b. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
c. Maintain a speed and a pressure that allow cutting without overheating the bit. Applying too much pressure will:

• Overheat the drill driver.
• Wear the bearings.
• Bend or burn bits.
• Produce off-center or irregularly shaped holes.

Masonry Drilling

For maximum performance, use carbide-tipped masonry bits when drilling holes in brick, tile, concrete, etc.

a. Maintain a speed and a pressure that allow cutting without overheating the bit or drill driver.
Applying too much pressure will:

• Overheat the drill driver.
• Wear the bearings.
• Bend or burn bits.
• Produce off-center or irregular-shaped holes.
  b. Apply light pressure and medium speed for best results in brick.
  c. Apply additional pressure for hard materials such as concrete.
  d. When drilling holes in tile, practice on a scrap piece to determine the best speed and pressure.
  e. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.

NOTICE: Fig. 12 shows some tips for different drilling operations.

Driving Nuts and Bolts

WARNING Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.

Variable-speed control must be used with caution for driving nuts and bolts with socket-set attachments. The technique is to start slowly, increasing speed as the nut or bolt runs down. Set the nut or bolt snugly by slowing the drill driver to a stop. If this procedure is not followed, the tool will have a tendency to torque or twist in your hands when the nut or bolt seats.

MAINTENANCE

WARNING
To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance.

Service
Preventive maintenance performed by unauthorized personnel may
WARNING
result in misplacing of internal wires and components which could **cause serious hazard. We recommend that all tool services be performed by a SKIL Factory Service Center or Authorized SKIL Service Station.
**

General Maintenance

WARNING
When servicing, use only identical replacement parts. Use of any other parts could create a hazard or cause product damage.

Periodically inspect the entire product for damaged, missing, or loose parts such as screws, nuts, bolts, caps, etc. Securely tighten all fasteners and caps and do not operate this product until all missing or damaged parts are replaced. Please contact customer service or an authorized service center for assistance.

Chuck Removal
The chuck can be removed and replaced with a new one.
a. Lock the variable-speed trigger switch by placing the direction-of-rotation selector in the center position. And set the torque-adjustment ring at Drill mode . Remove the battery.
b. Open the chuck jaws.
c. Insert a 5/16 in. or larger hex key (not included) into the chuck of the drill driver and tighten the chuck jaws securely.
d. Tap the hex key sharply with a mallet (not included) in a clockwise direction. This will loosen the screw in the chuck for easy removal.
e. Open the chuck jaws and remove the hex key. Using a Philips screwdriver (not included), remove the chuck screw by turning it in a clockwise direction.

NOTICE: The chuck screw has left-handed threads.
f. Insert the hex key into the chuck and tighten the chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen the chuck on the spindle. It can now be unscrewed by hand.

To Retighten a Loose Chuck
The chuck may become loose on the spindle and develop a wobble. Also, the chuck screw may become loose, causing the chuck jaws to bind and prevent them from closing.
To tighten a loose chuck or chuck screw:
a. Lock the variable-speed trigger switch by placing the direction-of-rotation selector in the center position. And set the torque-adjustment ring at Drill mode . Remove the battery.
b. Open the chuck jaws.
c. Insert a hex key (not included) into the chuck and tighten the chuck jaws securely. Tap the hex key sharply with a mallet (not included) in a clockwise direction. This will tighten the chuck on the spindle.
d. Open the chuck jaws and remove the hex key.
e. Use a Philips screwdriver (not included) to turn the chuck screw counterclockwise to tighten it.
Cleaning

WARNING
The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air. Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.
WARNING
Certain cleaning agents and solvents damage plastic parts. Some of these are gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia, and household detergents that contain ammonia.

Storage
Store the tool indoors in a place that is inaccessible to children. Keep away from corrosive agents.

TROUBLESHOOTING

2. Battery pack is not installed properly.
3. Burned out switch.| 1. Charge the battery.
2. Confirm battery is locked and secured to the tool.
3. Have the switch replaced by an Authorized SKIL Service Center or Service Station.
LED Worklight rapidly flashes.| 1. Tool is over-loaded.
2. Tool is over-temperature.| 1. Release the trigger switch.
2. Cool the tool under airflow.

LIMITED WARRANTY OF SKIL CONSUMER TOOLS

5 YEAR LIMITED WARRANTY

Chervon North America, Inc. (“Seller”) warrants to the original purchaser only, that all SKIL consumer TOOLS will be free from defects in material or workmanship for a period of five years from date of purchase, if original purchaser registers the product within 30 days from purchase. BATTERIES AND CHARGERS are warranted for 2 years. Product registration can be completed online at www.Registermyskil.com. Original purchasers should also retain their receipt as proof of purchase. THE FIVE- YEAR WARRANTY PERIOD FOR TOOLS IS CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF PURCHASE. If original purchasers do not register their product timely, the foregoing limited warranty will apply for a duration of three years for tools. All batteries and chargers will remain under the two- year limited warranty.
Notwithstanding the foregoing, if a SKIL consumer tool is used for industrial, professional, or commercial purposes, the foregoing warranty will apply for a duration of ninety days, regardless of registration.
SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement of parts, without charge, which are defective in material or workmanship and which have not been misused, carelessly handled, or repaired by persons other than Seller or Authorized Service Station. To make a claim under this Limited Warranty, you must return the complete product, transportation prepaid, to any SKIL Factory Service Center or Authorized Service Station. For Authorized SKIL Power Tool Service Stations, please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING BELTS, GRINDING WHEELS, AND OTHER RELATED ITEMS.
ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE TO SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME STATES IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA, AND FROM COUNTRY TO COUNTRY.
THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED STATES OF AMERICA, CANADA, AND THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL DEALER OR IMPORTER.
© Chervon North America, 1203 E. Warrenville Rd, Naperville, IL 60563.

01/21

References

• Log In to Your Owner Account | SKIL
• Innovative Tools with Tech You Can Use |SKIL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>