inovonics EN2224 Mobile Duress Pendant Family Instruction Manual

inovonics EN2224 Mobile Duress Pendant Family

Mobile Duress Pendant Family
Installation Instructions

Overview

The Inovonics mobile duress pendant is designed to provide indoor room and floor level location with a button press. Inovonics mobile duress pendants are only available to factory trained dealers and only compatible with the EN7295 mobile duress gateway and EN5060 locators. The mobile duress pendant is available in the following configurations:

Inovonics mobile duress pendants are shipped in bulk packaging so that orders can be fulfilled by removing pendants and batteries from packaging based on order quantity. Single pendant orders may be repackaged separately. To re- close the box after batteries are inserted into pendants, remove battery compartment divider at perforation along hinge.

Inovonics Contact Information

If you have any problems with this procedure, contact Inovonics technical support:

•  E-mail: support@inovonics.com.
•  Phone: 800-782-2709; 303-939-9336.

Pendant Transmitter Components

• Reset button
• Battery

Installation and Startup

Installation Notes

•  These products are designed to be installed and maintained by professional security technicians.
•  Products are intended for indoor use.
•  Manually test all products weekly.

Install the Battery

1.  Pry the housing apart at either end and pull the two halves apart.
2.  Install the battery..

Caution : Ensure that a new Panasonic CR2 or equivalent battery is always installed in the mobile duress pendant. Never install a used battery.

Register mobile duress pendants
All mobile duress pendants must be registered with the system in order to be used, monitored and supervised. When supervised, the mobile duress pendants will send a check-in message to the Inovonics gateway.

Note : These instructions cover the installation and operation of the mobile duress pendant. Please refer to the Inovonics Mobile Duress User Manual for instructions about registering pendants to a specific site’s mobile duress system. Please contact support or your account manager if you do not have a copy of the user manual.

Operation

Using The EN2233 Pendant Chain
Always use the chain included with the EN2233. Substituting stronger cords or chains may result in injury to the wearer.

Converting a Belt Clip Pendant to a Belt Loop
If you’d like to convert a belt clip pendant transmitter belt clip to a belt loop, secure the bottom of the belt clip to the housing with a coarse thread screw.

Figure 2 Use a coarse thread screw to secure the belt clip

Operate the Mobile Duress Pendant
Alarm signals are transmitted multiple times and are indicated by the blinking transmission LED. When the buttons are released, the transmitter sends an alarm restoral signal. To test a transmitter, activate each condition by pressing the button(s) and ensure the appropriate response.
EN2224
Activation of the conditions will depend on the application, as will the response. The application controller must be designed to recognize simultaneous messages. The EN2224 requires the use of an Inovonics serial receiver, and cannot currently be used with an Inovonics add-on receiver.

EN2233D/EN2235D
Press and hold both buttons simultaneously to activate an alarm.

EN2233S/EN2235S
Press the button for at least one second to activate an alarm.

EN2236D
To send the first condition, press and hold the left pendant button for one second; to send the second condition, press and hold the right pendant button for one second; to send the third condition, press and hold both buttons simultaneously.

EN2238D
To send the first condition, press and hold either the left or the right pendant button for one second; to send the second condition, press and hold both buttons simultaneously.

Specifications

• Typical battery life: 3 years.
• Battery type (BAT608): Panasonic CR2 or equivalent.
• Operating environment: 0 to 60°C (32 to 140°F), noncondensing.
• Compatible gateway: EN7295 mobile duress gateway.
• Regulatory compliance: FCC, Industry Canada, RoHS

Note: Specifications and data are subject to change without notice.

FCC RF Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.

FCC Part 15 and Industry Canada Compliance
This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Television and Radio Interference
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Limits
This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

References

• Unparalleled network infrastructure | Inovonics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>