milwaukee M18 Cordless Multi-Tool User Manual
- June 6, 2024
- Milwaukee
Table of Contents
milwaukee M18 Cordless Multi-Tool
GENERAL POWER TOOL SAFETY WARNINGS
GENERAL POWER TOOL SAFETY WARNINGStions provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-oper-ated (cordless) power tool.
WORK AREA SAFETY
- Keep work area clean and well lit. Cluttered or dark areas invite accidents. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
- Do not operate power tools in explosive atmo-spheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
- Keep children and bystanders away while operat-ing a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
- Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
- Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
- Do not expose power tools to rain or wet condi-tions. Water entering a power tool will increase the risk of electric shock.
- Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
- When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
- If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of an GFCI reduces the risk of electric shock.
PERSONAL SAFETY
- Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
- Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
- Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
- Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
- Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
- Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
- If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
- Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
- Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
- Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
- Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
- Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
- Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
- Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
- Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
- Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
- Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
- Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
- When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
- Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact ac-cidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
- Do not use a battery pack or tool that is dam-aged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
- Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or tem-perature above 265°F (130°C) may cause explosion.
- Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
SERVICE
- Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
- Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR MULTI-TOOL
- Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting ac-cessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
- Use clamps or another practical way to secureand support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.
- To reduce the risk of explosion, electric shock and property damage, always check the work area for hidden gas pipes, electrical wires or water pipes when making blind or plunge cuts.
- Keep hands away from all cutting edges and moving parts. Do not reach underneath the workpiece.
- Do not use dull or damaged blade, which can cause excessive friction, blade binding and kick-back.
- Know your workpiece. Remove nail and screw heads before scraping. Hitting hard objects with blade may cause the tool to kick back.
WARNING To reduce the risk of injury, when working in dusty situations, wear appropriate respiratory protection or use an OSHA compliant dust extraction solution.
Always use common sense and be cautious when using tools. It is not possible
to anticipate every situation that could result in a dangerous outcome. Do not
use this tool if you do not understand these operating instructions or you
feel the work is beyond your capability; contact Milwaukee Tool or a trained
professional for additional information or training. Maintain labels and
nameplates. These carry important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free replacement.
WARNING sawing, grinding, Some dust created by power sanding,drilling,
and other construction activities contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some examples of these chemicals
are:
- lead from lead-based paint
- crystalline silica from bricks and cement and other masonry products, and
- arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
SYMBOLOGY
- Volts
- Direct Current
- No Load Orbits per Minute (OPM)
- UL Listing for Canada and U.S.
FUNCTIONAL DESCRIPTION
- Inner flange
- Adapter
- Accessory bolt
- Quick release lever
- On/Off switch
- Handle
- Speed dial
SPECIFICATIONS
- Cat. No.2626-20
- Volts18 DC
- No Load OPM 11,000 – 18,000
- Battery Type M18™
- Charger Type M18™
- Operating Temperature 0°F to 125°F
ASSEMBLY
WARNING Recharge only with the chargercific charging instructions, read the operator’s manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons and pull the battery pack
away from the tool.
WARNING Always lock the trigger or removeis not in use.
Changing Accessories
- Remove the battery pack.
- Lift the quick release lever and push it firmly forward over the detent.
- Place the tool upside down on a flat surface.
- Unscrew the accessory bolt.
- Remove any accessories and any adapters (sold separately).
- Clean bolt, flange, adapter and accessories of all dirt and debris.
- Place the adapter (if necessary), accessory and bolt onto the tool. Determine the need for an adapter by using the chart. Hand tighten securely.
- Press the quick release lever back into place.
OPERATION
WARNING To reduce the risk of injury, keep moving parts. Always wear proper eye protection marked to comply with ANSI Z87.1. When working in dusty situations, wear appro-priate respiratory protection or use an OSHA compliant dust extraction solution. Always remove battery pack before changing or removing accessories. Only use accessories specifically recommended for this tool. Others may be hazardous.
Typical Applications
A large variety of accessories are available for ap-plications such as
sawing/cutting, scraping, and sanding.
Sawing/Cutting
Install a sawing/cutting blade at an angle easy to use. Properly clamp the
workpiece. Set the speed dial to a high speed. Start the tool and allow it to
reach full speed. Use moderate pressure to avoid burning or scorching the
workpiece.
Scraping
Install a scraping blade at an angle easy to use. Start the tool and allow it
to reach full speed. Use light pressure and a low angle to avoid gouging and
damaging the workpiece.
Sanding
Install a sanding backing pad at an angle easy to use. Attach a sanding disc,
or cut sandpaper to fit the backing pad. Generally, use 24 or 36 grit for
heavy stock removal; 50, 60, or 80 grit for medium stock removal and 120 or
240 grit for finishing. Always begin with a coarse grit, using successively
finer grits to obtain the desired finish. Properly clamp the workpiece. Start
the tool and allow it to reach full speed. Use light pressure and long,
sweeping, side to side strokes, advancing forward to produce the desired
finish.
WARNING To reduce the risk of explosion, electric shock and property dam- age, always check the work area for hidden gas pipes, electrical wires or water pipes when mak-ing blind or plunge cuts.
Selecting Speed
To set the maximum speed, rotate the speed dial. Set the speed dial to “1” for
the lowest speed (11,000 OPM). Set the speed dial to “12” for the highest
speed (18,000 OPM).
Starting/Stopping
- To start the tool, grasp the handle and slide the switch forward to the ON (I) position.
- Allow the tool to come to full speed before begin-ning work.
- Control pressure and surface contact between accessory and workpiece.
- To stop the tool, slide the switch back to the OFF (0) position. Make sure the tool comes to a com-plete stop before laying the tool down.
MAINTENANCE
WARNING To reduce the risk of injury, always unplug the charger and remove the battery pack from the charger or tool before performing any maintenance. Never disassemble the tool, battery pack or charger. Contact a MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good repair by adopting a regular
maintenance program. Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of parts, or any other
condition that may affect the tool operation. Return the tool, battery pack,
and charger to a MILWAUKEE service facility for repair. After six months to
one year, depending on use, return the tool, battery pack and charger to a
MILWAUKEE service facility for inspection. If the tool does not start or
operate at full power with a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-erly, return the tool,
charger and battery pack, to a MILWAUKEE service facility for repairs.
WARNING To reduce the risk of personal in jury and damage, never immerse your tool, battery pack or charger in liquid or allow a liquid to flow inside them.
Cleaning
Clean dust and debris from any vents. Keep tool clean, dry and free of oil or
grease. Use only mild soap and a damp cloth to clean, since certain clean-ing
agents and solvents are harmful to plastics and other insulated parts. Some of
these include gasoline, turpentine, lacquer thinner, paint thinner,
chlorinated cleaning solvents, ammonia and household deter-gents containing
ammonia. Never use flammable or combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and charger to the nearest
authorized service center.
ACCESSORIES
WARNING Use only recommended accesso For a complete listing of accessories, go online to www.milwaukeetool.com or contact a distributor.
SERVICE – UNITED STATES
1-800-SAWDUST (1.800.729.3878) Monday-Friday, 7:00 AM – 6:30 PM CST or visit
www.milwaukeetool.com Contact Corporate After Sales Service Technical Support
with technical, service/repair, or warranty questions. Email:
metproductsupport@milwaukeetool.com Become
a Heavy Duty Club Member at
www.milwaukeetool.com to receive important
LIMITED WARRANTY
USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is warranted to the
original purchaser only to be free from defects in material and workmanship.
Subject to certain exceptions, MILWAUKEE will repair or replace any part on an
electric power tool which, after examination, is determined by MILWAUKEE to be
defective in material or workman-ship for a period of five (5) years* after
the date of purchase unless otherwise noted. Return of the power tool to a
MILWAUKEE factory Service Center location or MILWAUKEE Authorized Service
Station, freight prepaid and insured, is required. A copy of the proof of
purchase should be included with the return product. This warranty does not
apply to damage that MILWAUKEE determines to be from repairs made or attempted
by anyone other than MILWAUKEE authorized personnel, misuse, alterations,
abuse, normal wear and tear, lack of maintenance, or accidents. Normal Wear:
Many power tools need periodic parts replacement and service to achieve best
performance. This warranty does not cover repair when normal use has exhausted
the life of a part including, but not limited to, chucks, brushes, cords, saw
shoes, blade clamps, o-rings, seals, bumpers, driver blades, pistons,
strikers, lifters, and bumper cover washers. This warranty does not cover Air
Nailers & Staplers; Airless Paint Sprayer; Cordless Battery Packs; Gasoline
Driven Portable Power Generators; Hand Tools; Hoist – Electric, Lever & Hand
Chain; M12™ Heated Gear; Reconditioned Product; and Test & Measurement
Products. There are separate and distinct warranties available for these
products. **The warranty period for Job Site Radios, M12™ Power Port, M18™
Power Source, Jobsite Fan and Trade Titan™ Industrial Work Carts is one (1)
year from the date of purchase. The warranty period for the M18 FUEL™ 1”
D-Handle High Torque Impact Wrenches, Drain Cleaning Cables, AIRSNAKE™ Drain
Cleaning Air Gun Accessories, REDLITHIUM™ USB Laser Levels and TRAPSNAKE™ 25′
Auger w/ CABLE DRIVE™ is two (2) years from the date of purchase. The warranty
period for the M18™ Compact Heat Gun, 8 Gallon Dust Ex-tractor, M18™ Framing
Nailers, M18 FUEL™ 1/2″ Ext. Anvil Controlled Torque Impact Wrench w/ ONE-
KEY™, M18 FUEL™ 1″ High Torque Impact Wrench w/ ONE-KEY™, M18 FUEL™ 2 Gal.
Compact Quiet Compressor, M12™ Laser Levels, 165′ Laser Detector, M12™ 23GA
Pin Nailer, M18 FUEL™ 1/4″ Blind Rivet Tool w/ ONE-KEY™, M12 FUEL™ Low Speed
Tire Buffer, M18 FUEL™ Dual Action Random Orbital Polishers, and the M18™
Utility Fencing Stapler is three (3) years from the date of purchase. The
warranty period for the LED in the LED Work Light and the LED Upgrade Bulb for
the Work Light is the lifetime of the product subject to the limitations
above. If during normal use the LED or LED Bulb fails, the part will be
replaced free of charge. Warranty Registration is not necessary to obtain the
applicable war-ranty on a MILWAUKEE power tool product. The manufacturing date
of the product will be used to determine the warranty period if no proof of
purchase is provided at the time warranty service is requested. ACCEPTANCE OF
THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION
OF THE CON-TRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT
AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT
SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR
PUNITIVE DAMAGES, OR FORANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS
ALLEGED TO BE AS A CONSE-QUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY
PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME
STATES DO NOT ALLOW THE EX-CLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES,
WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY
IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH
DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WAR-RANTIES ARE LIMITED TO
THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WAR-RANTY LASTS, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only. Please
consult the ‘Service Center Search’ in the Parts & Service sec-tion of
MILWAUKEE’s website www.milwaukeetool.com or
call 1.800. SAWDUST (1.800.729.3878) to locate your nearest service facility
for warranty and non-warranty service on a Milwaukee electric power tool.
References
- Milwaukee® Tool Official Site | Nothing but HEAVY DUTY®
- Milwaukee® Tool Official Site | Nothing but HEAVY DUTY®
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>