SHADOW STORM 30080 2.4G Remote Control Ship Instruction Manual

SHADOW STORM 30080 2.4G Remote Control Ship

INSTRUCTIONS

1. This product uses 370 strong magnetic drive system, and adopts advanced 2.4G frequency connection technology. The remote control distance is farther.
2. The high-performance lithium battery is configured for 7.4V1200MAH, and the speed is 20-25KM/H. The driving time is approximately 15 minutes.
3. Automatic turning technology: The ship adopts the design of tumbler. The ship has a self-overturning function, which can never overturn the ship.
4. The motor cooling system extends the service life of the model.
5. The left and right navigation rudder enhances the stability.
6. Low voltage alarm function: When the voltage is insufficient, the remote control will give an alarm. (After the alarm sounds, please return the ship immediately to prevent the model from powering out.)

Warning

1. This product is suitable for people aged over 8. It must be operated under the supervision of an adult.
2. After completing the voyage, the battery must be cooled before charging the battery.
3. When the ship is sailing, it must be ensured that there is no one in the area. There should be no aquatic or debris in the water to prevent the propeller from being hooked or damaging the ship.
4. This product has some small parts. Do not swallow to avoid the risk of suffocation.
5. Please keep a certain distance from the high-speed rotating propeller to avoid the danger of ground injury.
6. The motor is a high temperature component. Do not touch it to avoid the danger of burns.
7. Check whether the USB cable and other parts are damaged regularly. If it is damaged, stop using it until repaired.
8. When the ship model is sailing, please pay attention to safety first. If you lose control of the ship model, you must choose a safe and reliable method to retrieve it. The operator must not retrieve the ship model from the water without safety protection.

**Main structure diagram of remote control ship

**

Remote control battery installation

Charging batteries

1. The battery must be installed according to the correct polarity.
2. Do not mix new and old batteries.
3. Do not mix other types of batteries.
4. Non-rechargeable batteries cannot be charged.
5. Rechargeable batteries must be charged under adult supervision.
6. The power terminals must not have any short-circuit phenomenon.
7. Do not connect more than a certain number of power sources.
8. Please be sure to use the USB charging cable delivered by our company to charge the original battery, otherwise we will not be responsible for all the consequences.
9. The exhausted battery should be removed from the toy.

Installation steps of cabin battery

1. Turn the cabin switch, and open the lid of the cabin as shown in the figure.
2. Install the lithium battery in the battery holder in the cabin.
3. Make sure the lithium battery to be fastened in the battery holder.
4. Connect the battery and power cord plug.
5. Insert and install the cabin cover to the hull at a 45° angle as shown in the figure.
6. Rotate the cabin switch as shown in the figure until the cabin cover is locked.

Align the bow sleeve column with the hole in the bottom of the ship and install it in place.

Linking before manipulation

After the battery is installed, put the hull into the water (note: the ship needs to be in the water to be connected to electricity),At this time, the LED light on the ship flashes, then turn on the remote control power switch, the remote control power indicator flashes Flashes and emits a sound of “DI”, the lights of the ship’s main body and the remote control change from flashing to steady on.Success, you can start to control.

Remote control instructions

1. Forward: Push the throttle lever backwards and the boat moves forward
2. Backward: Push the throttle stick forward and the boat moves backward
3. Turn left: Push the steering wheel to the left when the boat is moving, the boat will turn left
4. Turn right: Push the steering wheel to the right when the boat is moving, the boat will turn right
5. Left fine-turning button: When the sailing ship automatically deflects to the right, if the operator presses the left fine-tuning button on the remote control, the ship will slowly return to the left until a direct flight is achieved.
6. Right fine-turning button: When the sailing ship automatically deflects to the left, if the operator presses the right fine-tuning button on the remote control, the ship will slowly return to the right until a direct flight is achieved.
7. Autopilot mode: Press the autopilot button on the remote control, it will automatically drive. Short press: “O” route demo Long press: “8” route demo. Press any button on the remote control again to exit the autopilot mode. Please operate this product in an open area.
8. High / Low speed setting
9. LED lighting control: The remote control LED light control button, press the hull LED light off, press again, the light is always on.

Maintenance

1. When the hull is finished sailing, please take out the lithium battery from the hull.
2. The hull surface should avoid prolonged exposure to the sun to eliminate the situation of paint peeling. After use, wipe the hull clean with a dry cloth.
3. If this product is not going to be used for a long time, please remove the control battery to avoid battery leakage, thus avoiding damaging the remote controller.

Accessories description

APPEND MANUAL

Produce name: RC TOY
Model: 2008
Manufacturer: GUANGDONG HENGDI TECHNOLOGY CORP.,LTD.
Address: THE WEST OF NINGCHUAN ROAH AND THE SOUTH OF HUANCUI ROAD, CHENGHAI ZONE, SHANTOU CITY, GUANGDONG PROVINCE, CHINA
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>