CRAFTMADE UC7224T4 Transmitter Panel Instruction Manual

Model: UC7224T4
INSTRUCTIONS FOR OPERATION

SETTING THE OPERATING CONTROLS

1. This unit operates on 23A a 12 volts battery (not included). To prevent possible damage if the battery should leak, be sure to remove the battery when the unit is not used.

2. This device which one of the black lines with an AC 120V power supply. the color of the ground wire is kelly.

3. Store the controller away from excess heat or humidity.

4. This remote control unit is required with 24bit code combinations. To prevent possible interference from or to other remote units such as garage door openers, car alarm, or security system. If you find that your fan and light kit go on and off without using your control, simply change the combination code in your transmitter and receiver.

5. Operation buttons on the panel of the transmitter.
   key– For fan HIGH-speed control.
   key– For fan MEDIUM speed control.
   key– For fan LOW speed control.
   key– For fan OFF speed control.
   OR OR key– For light brightness and light ON/OFF control.
   key– For fan speed Reverse.
   POWER SWITCH – for POWER ON/OFF

6. Start the fan :
   Press the fan button to run the fan at the desired.

7. Turn off the fan :
   Press the OFF button.

8. Light control :
   Turn the light on or off by only touching the LIGHT CONTROL button.
   Keep pressing the button in excess of 0.7 seconds it becomes dimmer, the light varies cyclically in 0.8 seconds.
   One of the important features of this control is AUTO-RESUME. After power is on, it allows the light to return to where it was off.

GENERAL INFORMATION :

This REMOTE controller is designed to separately control your ceiling fan speed and light brightness. The Light The ON/OFF button will control the light brightness  ON/OFF. The LED indicator on the transmitter will light when the button is pressed.

INSTRUCTIONS FOR INSTALLATION AND OPERATION OF FAN SPEED CONTROLLER

1. Setting the code on your new transmitter.
   Within 60 seconds of turning the AC power on, press and hold the OFF/STOP button for 5 seconds. The receiver will then lock in the chosen frequency. If your fan has a light it will blink twice, for fans without lights check operation using the transmitter

NOTICE: The changes or modifications not expressly approved by the par tire responsible or compliance could voiduser’sauthority top-rated hee equipment.

IM IMPORTANT NOTE: To comply with the FCC RFexposurecompliancerequirements, no change to the antenna or the devices is permitted. Any change to the antenna or the device could result in the device exceeding the exposure requirement stands voiduser’’’’sauth or city toop rate the device.

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the aim itsforaClassB a digital device, pursuant to part 15 of the cc Rules. This line is designed to provide reasonable
protection against harmful interference in a residential installation. This equipment it generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,m cause harm full in interference to radio comm unit on. However, there is no guarantee that reference will no to occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorientorrelocatethereceiving antenna.
-Increase the separation between the equip and receiver.
-They connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consultthedealeroran experienced radio/TV technician for help.

CAUTION:

Anychangesorm modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. received, including in reference that may cause Canada, Industry Canada(IC)Notices This device complies with Canada license-exempt RSS standard(s).  Operation is subject to the following two conditions:(1)this device may not cause in reference, and(2)this device must accept any interference, including interference that may cause undesired opera to of the device.
Canada,avisd’IndustryCanada(IC) Cap pareil question form eaves Industrie Canada exempted delicence RSS standard(s). Sonfoncti on neme ntestso umisau xdeuxco nditions suivantes:(1)cetappareilne

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>