Ducky DMFE20O-OAAPA7B Feather Ultralight Gaming Mouse User Manual
- June 6, 2024
- Ducky
Table of Contents
Model : DMFE20O-OAAPA7B
Interface : USB2.0
Sensor type : Optical
Sensor model : PixArt PMW3389
MAX tracking speed : 400 IPS / Acceleration: 50g
Surface : ABS
Total key amounts : 7
Micro switches : HUANO Mechanical rated for 50 million clicks
Scroller : Kailh encoder 9mm
LED : ARGB / RGB LED
Feet : High-density PTFE Teflon
DPI settings : 400/800/1600/3200/6400/12000/16000
USB polling rate : 125/500/1000 Hz
LOD : Low / Default / High
Cable : 1.8M Paracord (Ultra – flexible)
Product dimensions : 124 x 59 x 36 mm
Box dimensions : 180 x 108 x 60 mm
Net weight (without cable) : 65g
Made in China
Right-Hand mode
Left-Hand mode
Default: Right-Hand Mode
To enable the 6th and 7th button function
Operation: In the right-hand mode, please press the 6th + the middle button
for 3 seconds, the mouse will flash white light 2 times, that is to enable the
functionality of the 6th and 7th buttons for key switching operation.
Right / Left – Hand switch operation (note that the side keys will follow the switch operation at the same time
1. Default: Right – Hand mode
2. The 6th button in the right-hand mode is the startup key for switching
functions
3. Operation :
Press and hold the 6th button for 3 seconds the whole mouse keeps flashing red
light (blinking once every 2 seconds) then press the left-right button in
sequence the mouse flashes white light 1 to restore the current light Complete
the setting. (If you switch to left-hand mode the 6th button is also the
switch start key the entire the mouse continues to flash red (blinks once
every 2 seconds) press the left-right button in sequence then switch back to
right-hand mode )
Function Mode: The 7th button
- Default: Non – functional
- Operation: Press and hold the 7th button for 3 seconds the whole mouse keeps flashing red light (blinking once every 2 seconds) then the function mode will be enabled. The 7th button will be switched to the function key to replace → the Fn key. (To cancel the Fn key press the Fn key again for 3 seconds. After the entire mouse blinks green light twice the current light value will be restored. The Fn key will return to the default 7th button.
Function Mode
| Press the Fn key(The 7th button) | + | The 4th button | – | End |
|---|---|---|---|---|
| The 5th button | Home |
Right-Hand mode
Bottom switches and button
Exclusive/ Ascended cable SR structure
The ascended angle of the cable is 7.91° Which is consistent with the pulling power when we use the mouse. The working feeling will be as smooth as we use the mouse bungee.
**Back switches function
**
DPI value
- Default: Right-Hand Mode (No function on the 6th& 7th button)
- DPI value: Use the DPI button at the bottom to directly switch the preset value DPI indicator lights on scroller in sequence:
A. 400|
---|---
B. 800
C. 1600
D. 3200
E. 6400|
---|---
F. 12000
G. 16000
- Scroller LED will indicate the DPI value for 3 seconds, later it returns to the current light reflection.
USB Report rate(125/500/1000Hz)
-
Up to down in sequence : 125/500/1000 Hz
-
The default setting in the middle of the slide switch: 500 Hz
LOD: Lift Off Distance value (L/D/H) -
L=Low/ D=Default/ H=High
AS: Angle Snapping(Enable/Disable) -
Default: OFF
-
Enable AS/ Disable AS :
-
Press and hold the DPI button + the 5th button after release, the mouse flashes white light 2 times, which means the AS will be enabled or disabled.
Lighting mode operation
Hold the DPI button + the 4th button, the lighting mode starts switching in sequence.
| DPI button | + | the 4th button | = | Wave Mode |
|---|
Breathe Mode
Color cycle Mode
Raindrop Mode
Interactive Mode
Halo Mode
Fireworks Mode
Aurora Mode
Static Color Mode
LED Customization mode
LED OFF
Static color mode
By default, it is set to red.
To cycle through the 8 colors, hold the 4th button and press the 6th button.
The colors will cycle through this order:
Red->Orange->Yellow->Green->Blue->Purple->Pink->White
The color will automatically save.
LED customization operation
Hold the DPI button + the middle button for 3 seconds, the mouse will flash white light 3 times then the LED customization mode will be started.
Description :
- After entering the LED customization mode the 3 individual sections will light up the defaulting white color. The first section will flash once every second to show the section that we can customize. (Like the first section)
- At this moment the 4th button is adjusted to the function of “the previous color” and the 5th button is adjusted to the function of “ next color”.
- The 6th button is the confirmation key. When we press it the customized section will change to the next one. (e.g 1, 2, 3, 1, 2, 3,1 …)
- The 7th button is the save and flnish key. No matter in which section as long as the 7th button is pressed the current lighting sections will be saved and turned back to the general lighting reflect.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>