EM2GO EM022AC1B EV- Charging Station User Manual

EM2GO EM022AC1B EV- Charging Station

Thank you for choosing the EM2GO electric vehicle charging station.
With this unit you have chosen a high-precision charger equipped with many safety-relevant protective devices, which guarantees an all-round carefree charging of your vehicle.

Important Note

• Please read these important safety instructions for charging your vehicle.
• Please keep this user manual. The charger has many safety functions. Read all safety information and warnings in this manual to become aware of possible dangers.

Warning
Basic precautions should always be followed when using electrical products. This manual contains important instructions, including the following, which are required and must be followed during installation, operation and maintenance.

• Do not install or use the charger near explosive, caustic or flammable materials, chemicals or vapours.
• Switch off the input power of the charger before installing or servicing the charger.
•  The device is only designed for vehicles that are compatible with the IEC 62196 charging standard.
• Do not use the charger if it is cracked, frayed, broken or damaged
•  Do not try to open, disassemble, repair, manipulate or modify the device
• If you have any questions or repairs, please contact our customer service.
• Do not use the charger when you are in the vehicle or when exposed to heavy rain, snow or severe weather.
•  Be careful when transporting the charger.
•  Do not touch the charging connector with sharp metal objects
• Do not pull the charging cable with force or with sharp objects

Warning
The device must be installed, adjusted and serviced by qualified electricians or people who are familiar with the construction and operation of this type of EV-Charger Failure to follow this precaution could result in death or serious injury.

•  Incorrect installation and testing of the charger can lead to damage
• No liability is assumed for the resulting damage.
•  Make sure that the charging cable is well positioned during the charging process cannot be walked on, damaged or burdened.
•  Check the wire diameter according to the local electrical requirements
•  Switch off the corresponding power supply before starting the installation.

Technical data

• Operating voltage: 400V AC ±10% , 50-60 Hz, 3-Phases
• Operating current: 32 amps
• Max. Output power: typically 22 kW
• Housing: IP66, splash water protected
• Operating temperature : -25 to + 55 °C
• Display: Colour LCD, LED-stripes  Protection against: over and under voltage, overload protection, short circuit protection, over temperature protection, lightning protection, fault current (RCD A + 6mA DC).
• Connection: Type 2 plug (CT) | Type 2 socket (ST)
• Cable length : 6.1 meters (CT)
• Structure : CE standards EN61851-1: 2011, EN61851-22:2002
• Dimensions : 65 x 195 x 295 mm
• Weight : 7 Kg

Important Note:
According to §19 NAV of March 21, 2019, the operation of charging devices for electric vehicles must be reported to the responsible electricity provider before use (from 11 KW) and before installation (from 22 KW). This can also be done by the commissioned electrician. Please contact your electricity provider by phone or online for more information

Assembly
To install the charging station, follow the installation instructions on pages 5 and 6 of this manual.

Overview

1.  CEE plug with 1.5 meter connection cable suitable for 380V AC three-phase current pre-configured
2.  Colour display
3. On / off switch
4. . LED strip
5.  EV charger plug (CT) | Type 2 Socket (ST)

GB

Display
The high-resolution colour display of the EM2GO charging unit shows you the following information:

1. Real-time charging power
2.  3-phase data (voltage and current)
3.  Charging time
4. Power consumption
5. . Charging unit temperature
6. . Status display

LED strip display
The LED strip signals the status of the charger:

1.  No LED indication: Not in operation.
2.  LED permanently green: Charger is connected.
3. . LED green running: Charging in process
4. . LED permanently green: Charging process complete
5.  LED flashes red: There is a defect.

NOTE: If the LED strip flashes red, the protection electronics of the EV charger was addressed. In this case, please disconnect the mobile charger from the electric vehicle and from the power grid. Submit the connections, cables and charger to a visual inspection. If there are no visual defects, reconnect everything. If the red LED continues to flash, dis-connect the charger from the electric vehicle and the mains supply and contact your specialist consultant. Do not use the EV charger.

Charge vehicles

1.  First insert the CEE plug of the charger into a suitable socket.
2. Remove the protective cap of the type 2 plug and connect it to the vehicle‘s charging socket. Please note that the vehicle must be prepared and adjusted for charging.
3. The charging process begins.
4. If you have purchased the charging station as a socket type (ST), first connect your type 2 charging cable to the type 2 socket of the charging station, and then to the charging connection of your electric vehicle.
5.  When charging is complete, remove the Type 2 plug from the vehicle‘s charging socket. Put the protective cap back

NOTE: On some models, charging does not start automatically. In this case, press the switch on the charging unit.

Assembly instructions

Please take into account that the connection cable of the charging unit is only 150 cm (±5%), your three-phase connection socket should be in this area. Once the wall charger has been installed, switch off the fuse of the three- phase connection socket and connect the charging unit to the CEE socket. You can now switch on the fuse.The charging unit is equipped with an residual- current device (Type A RCD + 6ma DC filter). Please make sure that your three- pha se socket is equipped with suitable residual-current devices.

Mounting accessories

1. Place the paper template on the wall where you want to place the charging station. Make sure that the CEE power connection is within a radius of 1.5 meters. Drill holes according to the paper template.
2. Insert and countersink the dowels in the drill holes. Remove the paper template.
3. Screw the mounting plate to the wall with the 30 mm screws. The hooks must point upwards.
4. Place the charging station with the backside from above on the holding plate. Make sure that the eyelets are correctly positioned in the hooks of the holding plate.
5. (ST) Screw the type 2 plug of the charging station into the drill holes provided.
6. Mount the holder for the charging connection and the hook for holding the cable also on the wall.

No liability for possible damage will be accepted in the event of incorrect operation. If you need technical support, please contact our support team via our website www.em2go.de

Important Note:
According to §19 NAV of March 21, 2019, the operation of charging devices for electric vehicles must be reported to the responsible electricity provider before use (from 11 KW) and before installation (from 22 KW). This can also be done by the commissioned electrician. Please contact your electricity provider by phone or online for more information.

Warranty and maintenance

•  The warranty period for this charger is two years.
•  The warranty expires if:
•  No proof of purchase can be provided.
•  The warranty period specified by the manufacturer is exceeded.
• The instructions for use, maintenance and storage are not followed.
•  Damage or malfunction is caused by the ingress of foreign objects.
•  In case of repair, disassembly or modification by unauthorized persons.
•  Damage caused by force majeure (such as lightning, overvoltage, earthquake, fire, flood, etc.).
• Damage and malfunctions caused by other avoidable external factors.
•  Damage and malfunction caused by improper use of the equipment, such as the ingress of water or other liquids.
•  Damage and malfunction caused by the mains power supply and a voltage not specified for use with the charger.

We hereby declare, that this device carries the CE mark in accordance with the regulations and standards. It conforms with the fundamental requirements of the of (REDF) 2014/53/EU. EMC Directive 2014/30/EU, and the Low Voltage Directive 2014/35/EU. The full text of the EU declaration of conformity is available at the following internet address: www.d-parts.de/Konfo

Note on environmental protection:
After the implementation of the European Directive 2012/19/EU in the national legal system, the following applies:
Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details of this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilising old devices, you are making an important contribution to protecting our environment. 

References

• EM2GO.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>