anko MR-8870 Head Shaver User Manual

Head Shaver
User Manual

Model No.: MR-8870

Rev 1
Note: The specifications and/or components of this appliance are subject to change without prior notice.

Safety Instructions

When using electrical appliances, basic safety precautions should always be followed, including the following:

Carefully read this instruction manual before using the appliance, charger base, and USB cable.

• Keep the appliance, accessories, and USB cable out of reach of young children.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the Appliance and/or USB cable.
• Ensure children and babies do not play with plastic bags or any packaging materials.
• Do not disassemble the Appliance, charging base, and/or USB cable. There are no user-serviceable parts inside.
• VERY IMPORTANT: Ensure that the charging base, charger (not supplied), and/or USB cable do not get wet (water splashes, etc.). Do not use your charging base, charger or USB cable with wet hands. Do not immerse the charger base and/or the USB cable in water or other liquids or use near sinks, baths or showers.
• Only Charge the Appliance with the charging base and USB cable that was supplied with the Appliance.
• Only Charge the Appliance from an Extra Low Voltage Battery Charger (not supplied) with an output rating the same as indicated on the Appliance’s rating label.
• Position the USB cable properly so that they will not be walked on or pinched by items placed on or against them.
• Use the Appliance, charging base, accessories, and USB cable only for its intended use. The Appliance, accessories, charging base, and USB cable are intended for household use only and not for commercial or industrial use.
• Inspect the USB cable, Appliance, charging base, and accessories for damage before every use.
• Do not use the appliance if it has been dropped or any part of the Appliance, charging base, accessories, and/or the USB cable has been damaged.
• If the USB cable is damaged, call our customer service for a replacement.
• The use of accessories not intended for use with this Appliance may cause injuries to the user or damage to the Appliance, components, and/or the USB cable.
• Do not sit the Appliance on other appliances, on uneven surfaces or where it could be subject to heat sources (e.g., radiators or stoves), direct sunlight, excessive dust or mechanical vibrations. The Appliance charging base and/or USB cable must not be used outdoors if raining, near water, placed near a hot gas or electrical burner, or placed in a heated oven.
• Do not place or leave near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.
• Do not operate or charge the Appliance underneath or near flammable or combustible materials (e.g., curtains).
• Always switch off and unplug the USB charger cable when finished charging the appliance, or during lightning storms or when unused for long periods.
• Do not cover the appliance or charger when charging or when in use.
• Turn off and unplug before cleaning or storing.
• Any type of servicing, apart from ordinary cleaning, must be carried out by a qualified electrical person only. There are no user-serviceable parts in this Appliance, charging base or USB cable.
• Cleaning and user maintenance shall not be made by children without supervision.
• If this Appliance and USB cable is used by a third party, please supply the instruction manual with it.
• Do not misuse the USB cable. Never carry the Appliance by the USB cable or pull to disconnect it from the socket. Instead, grasp the plug and pull to disconnect.
• Do not insert or allow foreign objects to enter any openings as this may cause damage to the Appliance and/or injury to the user.
• Do not leave the Appliance running or charging unattended.
• No liability can be accepted for any damage caused by non-compliance with these instructions or any other improper use or mishandling of the Appliance, charging base, and/or USB cable.
• This product has not been designed for any uses other than those specified in this manual.
• ONLY for domestic use. Industrial or commercial use invalidates the warranty.

WARNING
Only use the USB Cable and Charging Base that was supplied with this Appliance. Consumers are cautioned against trying to replace the battery. Using and/or purchasing counterfeit and/or inferior-quality batteries have the potential to cause fire, personal injury, and/or damage to property. These batteries are typically found on online-auction websites or from other retailers and are known to pose a potential safety risk. Never try to charge non-rechargeable batteries as they may explode or catch on fire or cause personal injury and/or damage to property.

– Batteries may explode if disposed of in fire.
– The battery is not replaceable. Do Not open the appliance.
– Do not use or store in temperatures above 40°C

**** At the end of the appliance’s life, it must be disposed of correctly. Contact your local waste management authority for more information on Battery Recycling and disposal regulations in your area. Do not dispose of electrical appliances or batteries as unsorted municipal waste, use separate collection facilities. Contact your local council for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. Please contact your local council or regional authority for more information on the collection, reuse, and recycling programs.

Read and Save These Instructions

Components

Instructions for Use

NOTE: This appliance and its accessories are rated IPX5 waterproof except for the charging base and USB cable.
This means, other than the charging base and USB cable, the appliance, and accessories can be used whilst in the shower and can be cleaned under the tap.
3.1 Charging the Appliance
Read the Safety Instruction first.
IMPORTANT: This Appliance contains a built-in lithium-ion battery which must only be charged using the supplied USB cable. Always switch off and unplug the USB cable when charging is completed or when not in use. If any abnormality occurs during charging, (such as a burning smell or excessive heat or even a strange sound) immediately turn off the charger and disconnect the USB cable, then contact our service department for assistance.
IMPORTANT: The Appliance must be fully charged before first use. Note: The USB cable can be plugged into the Charging Base or plugged directly into the bottom of the appliance.

• Take the USB Cable and fully unravel it before using it to charge the Appliance.

• If using the charging base, plug the small end of the USB cable into the side of the charging base
  

• Place the appliance upside down on the charging base.

• Plug the large end of the USB cable into your 5Vd.c. 1A USB charger (not supplied) and switch on.
  The LED display will light up indicating it is charging and will show the level of charge. This also shows the level of discharge during use.
  

• If using without the charging base, plug the small end of the USB cable directly into the bottom of the appliance.

• Plug the large end of the USB cable into your 5Vd.c. 1A USB charger (not supplied) and switch on.

• The LED display will light up and indicate the charge and level of charge.

Operation

4.1 Shaver for Body

• With the appliance fully charged and the Shaving attachment fitted, holding firmly in your hand, press the On / Off button, which is located just above the LED display, to turn on. (press again to turn off).

• To use the Shaver:
  Once the shaving attachment (1) is fitted, press the On / Off button, then gently press the blades against your body part to be shaved, and gently move the shaver in any direction.
  A gentle circular motion is the preferred most comfortable movement however any motion can be applied when navigating the contours of the body.

4.2 Shaver for Head

Lightly press the blades against your scalp and move the shaver slowly around your head in a circular motion or whichever motion you feel is most comfortable for cutting your hair.
Do not attempt to shave hair that is longer than a few days’ growths as head- shaving is designed to maintain the shaved appearance and this look can be achieved by daily use if desired.

Important: Always attach the shaver blade cover when not in use to protect the fragile blade assembly.

4.3 Hair Trimmer The appliance comes with a Hair Trimmer attachment along with various height comb attachments for varying trim heights. This attachment can be used for trimming sideburns, mustaches, beards, eyebrows, neck hair, etc.

• To attach, first remove the shaver head attachment by grasping the appliance body with one hand, grasp underneath the shaver head with the other hand, and then pull the two apart.
  

• Take the Hair Trimmer attachment and whilst aligning the two ribs on either side of the trimmer shaft with the two slots in the appliance body, push the trimmer in all the way until it clicks, making sure it is seated properly. You can attach any of the Height Combs that you require.

• To do this, hook the comb over the front of the trimmer then push it down on the back of the comb until it clicks in place.
  

• To remove, lift up the small tab and swing up and forward.

• To use the Trimmer:
  Once the desired hair trimmer Comb size (10) is fitted, press the On / Off button to turn it On, then in a scooping motion move the comb through the hair against the growth of hair working your way slowly so as not to snag or pull when cutting longer hair. When cutting hair on the top of your head work from front to back in a similar motion. When finished press the On / Off button to turn the unit off.

4.4 Nose Trimmer
The appliance comes with a Nose Hair Trimmer attachment. This attachment can be used for trimming the protruding hairs from your nostrils.

• To attach, first remove the shaver head (or any other attachment being used) attachment by grasping the appliance body with one hand, grasping underneath the shaver head with the other hand, and then pulling the two apart.
  

• Take the Nose Hair Trimmer attachment and whilst aligning the two ribs on either side of the trimmer shaft with the two slots in the appliance body, push the Nose Hair trimmer in all the way until it clicks, making sure it is seated properly.
  

• To use the Nose Trimmer:Once the Nose Trimmer attachment (4) is fitted press the On / Off button, then gently place the nose trimmer into one nostril and work in a circular motion around the internal area of the nostril cavity.
  CAUTION: Be very careful not to push the trimmer too far up into the nasal cavity as this may become uncomfortable.
  Once finished, turn the unit off by pressing the On / Off button, check and clean the nose trimmer attachment if necessary and repeat the same procedure on the other nostril.

4.5 Facial Cleansing Brush and Silicone Brush
The appliance comes with a Facial Cleaning Brush and Silicone Brush attachment. These attachments can be used scrubbing away sweat, dirt, and oil. They can help with deep cleaning of facial pores more gently and hygienically. The silicone brush can also provide facial massage at the same time as the cleaning.
Note: Remove the plastic cover from the Bristle Brush before use, but remember to fit the cover back when finished to keep the bristles in shape.

• To attach, first remove the shaver head (or any other attachment being used) attachment by grasping the appliance body with one hand, grasping underneath the shaver head with the other hand, and then pulling the two apart.
  

• Take the Bristle Brush attachment and whilst aligning the two ribs on either side of the trimmer shaft with the two slots in the appliance body, push the Bristle Brush in all the way until it clicks, making sure it is seated properly.

• To use the Facial Cleansing Brush: Wet the area to be cleansed and apply a facial cleanser. Once the facial cleaning brush (3) is fitted, press the On / Off button, then gently apply the brush to your face and move it in a circular motion. When finished press the On / Off button to turn the unit off.
  To use the Silicon Brush, remove the bristle brush from the Brush Holder (both brushes use the same holder) Hold the Brush holder and pull the bristle brush up and off.
  

• To use the Silicon Brush:
  Wet the area to be cleansed and apply a facial cleanser.
  Once the Silicon Brush (9) is fitted, press the On / Off button, then gently apply the brush to your face and move it in a circular motion.
  When finished press the On / Off button to turn the unit off.

Care and Cleaning

5.1 Cleaning
To ensure optimal shaving efficiency, the shaver must be cleaned regularly.
IMPORTANT: Do Not use flammable liquids, chemicals, abrasive creams, steel wool or scouring pads for cleaning.
DO NOT press on the top of the shaving blade surfaces as you will damage them. The easiest and most sanitary way to clean the product is to wash the shaver head part and the whisker container with fresh warm (not hot) water each time after use
. To do this:

• Turn off the Shaver

• Pry open each blade section one by one and then rotate them fully open to expose the inner whisker container.

• Repeat for the other three-blade sections.
  

• Remove the Centre Blade Section. To do this, grasp the center blade surround and rotate anti-clockwise to unclip, then lift up and away.
  

•  You can brush out the whiskers with the small supplied cleaning brush and then rinse the shaver head parts, the Blade Sections, and the whisker container for a minute or so until the whiskers have been washed away.
  DO NOT wipe the Blade Sections with a towel or paper tissues as this will cause damage to the shaver head. Only use running tap water to rinse away the whiskers and allow the Blade Sections to dry naturally before re-assembly.

• When clean, gently shake the excess water from the appliance.

• Allow the appliance and Blade sections to sit and air dry naturally, and only when dry, refit the Centre Blade Section in the reverse method of disassembly. Ensure it is rotated clockwise and locked in place.

• Close the four-blade sections ensuring the latch is shut.

• The other accessories can also be cleaned using running tap water and then allowed to air dry naturally. NOTE: Cleaning and user maintenance shall not be made by children without supervision

5.2 Lubrication
The Hair Trimmer will need periodic lubrication to allow the blades to run smoothly.
Use a drop of sewing machine oil every few months of use directly onto the trimming blades.

Storage

• Switch off and unplug the appliance.
• Coil the USB cable loosely. Do not kink or pull the cable tight.
• Ensure all parts are completely dry.
• Fit the plastic Shaver Blade Cover to prevent damage.
• Store your appliance and accessories in a cool, dry location

Technical Specifications

Input: 5Vd.c. 1A
Battery Type: Li-ion 3.7V 600mAh
Charge Time: approx. 1.5hr
Working Time : approx. 1hr

Warranty Against Defect

12 Month Warranty
Thank you for your purchase from Kmart. Kmart Australia Ltd warrants your new product to be free from defects in materials and workmanship for the period stated above, from the date of purchase, provided that the product is used in accordance with accompanying recommendations or instructions where provided. This warranty is in addition to your rights under the Australian Consumer Law. Kmart will provide you with your choice of a refund, repair or exchange (where possible) for this product if it becomes defective within the warranty period. Kmart will bear the reasonable expense of claiming the warranty. This warranty will no longer apply where the defect is a result of alteration, accident, misuse, abuse or neglect. Please retain your receipt as proof of purchase and contact our Customer Service Centre at 1800 124 125 (Australia) or 0800 945 995 (New Zealand) or alternatively, via Customer Help at Kmart.com.au for any difficulties with your product. Warranty claims and claims for expenses incurred in returning this product can be addressed to our Customer Service Centre at 690 Springvale Rd, Mulgrave Vic 3170. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. For New Zealand customers, this warranty is in addition to statutory rights observed under New Zealand legislation.

IMPORTANT!
For all technical queries or difficulties in operating the product and for spare parts, contact H.E. Group customer service at 1300 105 888 (Australia) and 09 8870 447 (New Zealand).

References

• Kmart.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>