Miele PG 8581 Dental Thermal Washer Installation Guide

: June 6, 2024
: Miele

Table of Contents

Miele PG 8581 Dental Thermal Washer
Technical data sheet
Installation plan
DIMENSIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Miele PG 8581 Dental Thermal Washer

Technical data sheet

PG 8581 Washer-disinfector
PG 8582 Med
PG 8583 Laboratory Glassware Washer

Legend: Circled, bold-type abbreviations:
Connection required

| Electrical connection| Voltage (default)

Rated load

| 2 AC 208V 60 Hz

6.2 kW

| 2 AC 208V 60 Hz

6.2 kW

---|---|---|---|---
PG 8581

PG 8582

| Fuse rating

Minimum cross-section

| 2 x 30 A

3 × AWG 10

| 2 x 30 A

3 × 5.2 mm²

Rated load

| 3 AC 208V 60 Hz

6.2 kW

| 3 AC 208V 60 Hz

6.2 kW

PG 8581

PG 8582

Rated load

| 2 AC 240V 60 Hz

6.2 kW

| 2 AC 240V 60 Hz

6.2 kW

(240V Option

PG8581)

| Fuse rating

Minimum cross-section

| 2 x 30 A

3 × AWG 10

| 2 x 30 A

3 × 5.2 mm²

Rated load

| 3 AC 240V 60 Hz

6.2 kW

| 3 AC 240V 60 Hz

6.2 kW

(240V Option

PG8581)

Rated load

| 3 AC 208V 60 Hz

6.2 kW

| 3 AC 208V 60 Hz

6.2 kW

Rated load

| 2 AC 208V 60 Hz

6.2 kW

| 2 AC 208V 60 Hz

6.2 kW

Installation plan

The machine is supplied with electrical cord and plug. The receptacle must be accessible after machine installation. For hard-wired machines, connection should be made via a suitable mains switch with all-pole isolation. The contact opening between all open contacts must be at least 3 mm wide and the mains switch must be lockable in the open position. If necessary, an equipotential bond with good contact connection must be provided in accordance with all appropriate national and local regulations.
Splash protection class IP 21

The machine is supplied with electrical cord and plug. The receptacle must be accessible after machine installation. For hard-wired machines, connection should be made via a suitable mains switch with all-pole isolation. The contact opening between all open contacts must be at least 3 mm wide and the mains switch must be lockable in the open position. If necessary, an equipotential bond with good contact connection must be provided in accordance with all appropriate national and local regulations.

Splash protection class IP 21

| Equipotential bonding and earthing| There is a screw connection point at the back of the machine, to which equipotential bonding can be connected if required.

Connect equipotential bonding and protective earth conductor!

| Network/ printer connection (optional)| Optional machine interface for transmission or process data output Communication module (not supplied)

Ethernet module or RS232 module (install electrical sockets near machine if required)

73 gpg

| 65 °C

70 °dH

29 psi

| 65 °C

200 kPa

---|---|---|---|---
| Min. flow pressure| 4.4 psi| 30 kPa
| Max. pressure| 145 psi| 1,000 kPa
| Connection thread – on site (flat sealing)| 3/4“ Male Garden Hose Thread| 3/4“ Male Garden Hose Thread
| Throughput| 2 gal/min| 7.5 l/min
| Length of connection hose (supplied)| approx. 5‘ 7“| approx. 1.7 m

PG 8583 only:

Model with feed pump for unpressurised demineralised water (ADP)

| Minimum flow pressure (DI unpressurized) Maximum pressure (DI unpressurized)

Machine connection nipple (outer dia. x l)

| 1.3 psi

8.7 psi

1/4“ x 3/16“

| 8.5 kPa 60 kPa

6 mm x 30 mm

(note machine model)

| Connection for up to two dispensing units for liquid agents on the back panel.
| Machine feet| Height-adjustable| 0-2 3/8“| 0 – 60 mm
| Foot diameter| 1 3/8“| 35 mm
| Entry point into housing| 8 M| 8 M
| Heat Dissipation to

Room

| Heat transfer by emission

Load on removal

| 1,194 btu/h

1,365 btu/h

| 0.35 kWh/h

0.40 kWh/h

Machine data	Height	32 7/8“
Height without lid	32 1/4“	820 mm
Width	23 5/8“	598 mm
	23
	5/8“
Depth		598 mm
	598 mm27
	1/2“
Door height	24 1/2“	622 mm
Net weight	163 lbs	74 kg
Dynamic floor load	1,200 N	1,200 N
Width including transport pallet	26 3/8“	670 mm
Depth including transport pallet	29 3/8“	740 mm
Height including transport pallet	36 1/4“	920 mm
Set-up Conditions	Ambient temperature Max. humidity	40-105 °F

80%

| 5-40 °C

80%

| Max. altitude above sea level| 4,921‘| 1,500 m

It is essential to observe the installation instructions when installing the machine.

In order to reduce the risk of steam damage, the area around the machine should be limited to furniture and fittings that are designed for use in commercial environments.

Installation should only be performed by Miele Service or authorized installers in accordance with valid regulations, relevant standards and health and safety codes!