SPIN MASTER 6064318 The Batman Batcycle RC with Batman Rider Action Figure Instruction Manual
- June 6, 2024
- SPIN MASTER
Table of Contents
SPIN MASTER 6064318 The Batman Batcycle RC with Batman Rider Action
Figure
BATCYCLE™ RC
CONTENTS
CAUTION:
HAIR ENTANGLEMENT Tieback and cover hair and secure loose clothing prior to playing.
1 controller
HOW TO DRIVE
HOW TO INSTALL BATTERIES CONTROLLER:
- Open the battery door with a screwdriver. If used batteries are present, remove these batteries from the unit by pulling up on one end of each battery. DO NOT remove or install batteries using sharp or metal tools.
- Install new batteries as shown in the polarity diagram (+/-) inside the battery compartment.
- Replace battery door securely. Check your local laws and regulations for correct recycling and/or battery disposal
VEHICLE
- Move the power switch to the OFF position.
- Open the battery door with a screwdriver and remove the battery box. If used batteries are present, remove these batteries from the unit by pulling up on one end of each battery. DO NOT remove or install batteries using sharp or metal tools.
- Install new batteries as shown in the polarity diagram (+/-) inside the battery compartment.
- Install battery box and replace battery door securely. Check your local laws and regulations for correct recycling and/or battery disposal.
HOW TO CONNECT THE CONTROLLER
- Turn on the vehicle and place on a flat surface.
- Press any button on the controller.
- You are ready to drive. Use the remote control to drive.
CONTROLLER NOT CONNECTING
NOTE : If your vehicle does not connect to the controller the first time, turn the vehicle off, remove batteries from the remote and put back in and repeat the HOW TO CONNECT THE CONTROLLER instructions. If normal function of the product is disturbed or interrupted, strong electromagnetic interference may be causing the issue. To reset product, turn it completely off, then turn it back on. If normal operation does not resume, move the product to another location and try again. To ensure normal performance, change the batteries, as low batteries may not allow full function.
SAFETY PRECAUTIONS
Keep hands, hair and loose clothing away from the motor/ wheels when power switch is turned ON. – Remove batteries when not in use. – Parental guidance is recommended for the play. – Keep your toy in your sight so that you can supervise it all the time. – New alkaline batteries are recommended to obtain maximum performance. – Users should keep strict accordance with the instruction manual while operating the product. Note: Parental guidance is recommended when installing or replacing batteries. Under the environment with electrostatic discharge, the toy may malfunction and require user to reset the toy.
CARE AND MAINTENANCE
Always remove batteries from the toy when it is not being used for a long period of time. Wipe the toy gently with a clean damp cloth. Keep the toy away from direct heat. Do not submerge the toy in water. This can damage the electronic assemblies.
BATTERY SAFETY INFORMATION
Batteries are small objects. Replacement of batteries must be done by adults. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the toy. Dispose of used batteries properly. Remove batteries for prolonged storage. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (i.e. alkaline/standard/rechargeable). Using rechargeable batteries is not recommended due to possible reduced performance. Rechargeable batteries are only to be charged under adult supervision. Replaceable-rechargeable batteries are to be removed from the toy before being charged. DO NOT recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.
REQUIRES 4 x 1.5V AA (LR6) and 2 x 1.5V AAA (LR03) BATTERIES (not included)
Batteries or battery packs must be recycled or disposed of properly. When this product has reached the end of its useful life, it should not be disposed of with other household waste. The Waste Electrical and Electronic Equipment Regulations require it to be separately collected so that it can be treated using the best available recovery and recycling techniques. This will minimize the impact on the environment and human health from soil and water contamination by any hazardous substances, decrease the resources required to make new products and avoid using up landfill space. Please do your part by keeping this product out of the municipal waste stream! The “wheelie bin” symbol means that it should be collected as “waste electrical and electronic equipment”. You can return an old product to your retailer when you buy a similar new one. For other options, please contact your local council.
FCC STATEMENT
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation. This equipment has
been tested and found to comply with the limits for Class B digital devices
pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference to radio communications.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction, may cause harmful
interference to radio communication. However, there is no guarantee that
interference will not occur in a particular installation. If this toy does
cause interference to radio or television reception (you can check this by
turning the toy off and on while listening for the interference), one or more
of the following measures may be useful: • Reorient or relocate the receiving
antenna • Increase the separation between the toy and the radio or the TV •
Consult the dealer or an experienced TV-radio technician for help.
NOTE : Changes, adjustments or modifications to this unit, including but
not limited to, replacement of any transmitter component (crystal,
semiconductor, etc) could result in a violation of FCC rules under part 15
and/or 95 and must be expressly approved by Spin Master Ltd or they could void
the user’s authority to operate the equipment. Spin Master Inc., PMB #10053,
300 International Drive, Suite 100, Williamsville, NY 14221. To contact the
responsible party please visit fcc.spinmaster.com
Spin Master International B.V. hereby declares that the radio equipment type BATCYCLE™ RC is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://doc.spinmaster.com