T S Brass B-0600 Series Kettle and Pot Filler Instruction Manual

T S Brass B-0600 Series Kettle and Pot Filler

Limited One Year Warranty

(Commercial Applications)
T&S warrants to the original purchaser (other than for purposes of resale) that such product is free from defects in material and workmanship for a period of one (1) year from the date of purchase. During this one-year warranty period, if the product is found to be defective, T&S shall, at its options, repair and/or replace it. To obtain warranty service, products must be returned to…

T&S Brass and Bronze Works, Inc.
Attn: Warranty Repair Department
2 Saddleback Cove
Travelers Rest, SC 29690

Shipping, freight, insurance, and other transportation charges of the product to T&S and the return of repaired or replaced product to the purchaser are the responsibility of the purchaser. Repair and/or replacement shall be made within a reasonable time after receipt by T&S of the returned product. This warranty does not cover Items which have received secondary fi nishing or have been altered or modifi ed after purchase, or for defects caused by physical abuse to or misuse of the product, or shipment of the products.

Any express warranty not provided herein, and any remedy for Breach of Contract which might arise, is hereby excluded and disclaimed. Any implied warranties of merchantability or fi tness for a particular purpose are limited to one year in duration. Under no circumstances shall T&S be liable for loss of use or any special consequential costs, expenses or damages.

Some states do not allow limitations on how long and implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. Specifi c rights under this warranty and other rights vary from state to state.

Attention California Residents:
WARNING This product can expose you to chemicals including Lead, Chromium (hexavalent compounds) and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

P/N: 098-006105-45
Rev.2 Date: 08-23-18
Drawn: TEH
Checked: DMH 11-20-18
Approved: JHB 11-30-18

Exploded View

Part Number Guide

Vacuum Breaker & Faucet Assemblies

Spray Valve Assembly

Installation: B-0600

Other units will be similar, except where noted.

1. Shut off water supply and drain lines. Existing supply lines should be roughed into wall or sink decking. Use ½” NPT inlets.
2. Install no.1 to supply line, using tefl on tape. Flange no.1A should screw in toward body no.1B. Once no.1 is in place, adjust flange against wall or sink deck.
3. Attach no.17 to no.4 (with no.15 in place). Attach other end of no.17 to no.14 or no.18 (with no.15 and hold down ring in place, where used.)
4. Turn on water supply and check for leaks.

Note: Installation of B-0610 and B-0611 requires (2) two supply lines (Hot and Cold) roughed into wall or sink deck, 8” center to center. Use tefl on tape on threads.
Note: B-0601, B-0606 and B-0611 do not have squeeze valves at end of hose. No.18 is attached directly into end of no.17.

RELATED T&S BRASS PRODUCT LINE

T &S BRASS AND BRONZE WORKS, INC.
A fi rm commitment to application-engineered plumbing products

2 Saddleback Cove, P.O. Box 1088,
Travelers Rest, SC 29690 Phone: 864-834-4102
Fax: 864-834-3518
E-mail: tsbrass@tsbrass.com

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>